2018 Lexus LC500 instrument panel

82
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
2-1.Instrument clus te r
For the purpose of explanation, the following illustrations display all warning lights
and indicators illuminated.
LC500
LC500h
Warning lights and indicators
The warning lights and indicators on th e instrument cluster, center panel and
outside rear view mirrors inform the driver of the status of the vehicle’s various
systems.
Instrument cluster

84
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
panel.
The indicators inform the driver of the
operating state of the vehicle’s various
systems.
WARNING
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on
when you start the engine , this could mean that these systems are not available to help protect you in an
accident, which could result in death or serious injury. Have the vehicle inspected by any authorized Lexus retailer or Lexus
authorized repairer, or any reliable repairer immediately if this occurs.
Indicators
Turn signal indicator
( P.186)
Tail light indicator ( P.191)
Headlight high beam indica-
tor ( P.192)
(If equipped)
Automatic High Beam indica-
tor*1 ( P.193)
Rear fog light indicator
( P.196)
(If equipped)
Gear Shift Indicator*2
( P.178, 185)
Cruise control indicator*2
( P.229, 239)
(If equipped)
Dynamic radar cruise control
indicator*2 ( P.229)
Cruise control “SET” indica-
tor*2 ( P.229, 239)
(white)
LKA indicator*2 (P.218)
(green)
LKA indicator*2 (P.218)
(orange)
LKA indicator*2, 3 (P.218)
Lexus parking assist-sensor
indicator ( P.243)
Slip indicator*1, 3 ( P.263)
VSC OFF indicator*1
( P.263)
PCS warning light*1, 4
( P.212)
(If equipped)
BSM (Blind Spot Monitor)
outside rear view mirror indi-
cators*5, 6 ( P.248)
(If equipped)
BSM (Blind Spot Monitor)
indicator ( P.248)
(If equipped)
RCTA (Rear Crossing Traffic
Alert) indicator ( P.248)
Brake hold standby indica-
tor*1 ( P.189)
Brake hold operated indica-
tor*1 ( P.189)
Security indicator*7 ( P.70,
76)
Smart entry & start system
indicator*2 ( P.163)

86
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
by any authorized Lexus retailer or
Lexus authorized repairer, or any reli-
able repairer.
*6: This light illuminates on the outside rear
view mirrors.
*7: This light illuminates on the center
panel.
*8: When the outside temperature is
approximately 3°C (37°F) or lower, the
indicator will flash for approximately 10
seconds, then stay on.
■Eco Driving Indicator (LC500)
Eco Driving Indicator Light
During Eco-friendly acceleration (Eco driv-
ing), the Eco Driving Indicator Light will
turn on. When the acceleration exceeds the
Zone of Eco driving, or when the vehicle is
stopped, the light turns off.
Eco Driving Indicator can be enabled on
the multi-information display. ( P.92)
Eco Driving Indicator Zone Display
Suggests the Zone of Eco driving with cur-
rent Eco driving ratio based on accelera-
tion.
Eco driving ratio based on acceleration
The part that exceeds the Zone of Eco driv-
ing illuminates in white.
Zone of Eco driving
Eco Driving Indicator will not operate under the following conditions:
●The shift position is in any position other than D.
●A paddle shift swit ch is operated.
●Eco Driving Indicator Light: Neither normal mode nor Eco drive mode is selected.
Eco Driving Indicator Zone Display: Eco drive mode is not selected.
●The vehicle speed is approximately 130 km/h (80 mph) or higher.
■Hybrid System Indicator (LC500h)
Charge area
Shows regeneration* status. Regenerated
energy will be used to charge the hybrid
battery (traction battery).
Hybrid Eco area
Shows that gasoline engine power is not
being used very often.
The gasoline engine will automatically stop
and restart under various conditions.
Eco area
A
B
C
D
A
B
C

89
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
Outside temperature
Displays the outside temperature within the range of -40°C (-40°F) to 50°C (122°F)
Low outside temperature indicator comes on when the ambient temperature is 3°C (37°F)
or lower
Tachometer
Displays the engine speed in revolutions per minute
Speedometer
Shift position/shift range/gear position ( P.173, 179)
Shift position indicator ( P.175, 181)
Clock
Time displayed is linked to the analog clock on the instrument panel. (P.297)
Engine coolant temperature gauge
Displays the engine coolant temperature
If the engine coolant temperature gauge indi cator enters the red zone, a buzzer sounds
and the high coolant temperature warning light comes on
Odometer and trip meter display
Odometer:
Displays the total distance the vehicle has been driven
Trip meter:
Displays the distance the vehicle has been driven since the meter was last reset
Trip meters “A” and “B” can be used to record and display different distances independently
Fuel gauge
Displays the quantity of fuel remaining in the tank
Multi-information display
Presents the driver with a variety of vehicle data (P.92)
Displays warning messages in case of a malfunction (P.378)
Motor power display/Hybrid System Indicator (LC500h)
Displays the motor power display (P.87) or Hybrid System Indicator (P.86)
■Speed warning
When the vehicle reaches the set
speed, the speed warning display will
flash.
This setting can be enabled on the
multi-information display. ( P.92)
Always observe the legal speed limit when
driving on public roads.
■Rev indicator
When the engine reaches a set speed
or the red zone, a ring-shaped indica-
tor will be displayed on the tachometer.
B
C
D
E
F
G
H
I
J
K
L

90
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
The indicators will be displayed in
amber ( ) when the engine speed
reaches a set speed, and in red ( )
when the engine speed reaches the
red zone. This setting can be enabled
on the multi-information display.
( P.97)
■Rev peak
When the engine speed reaches or
exceeds the following, an afterimage of
the tachometer will be displayed at the
highest engine speed for approxi-
mately 1 second.
LC500: 3600 r/min
LC500h: 4000 r/min
■The meters and display illuminate when
The engine switch

is in
IGNITION ON mode .
■Variable red zone (LC500)
To help protect the engine, the engine
speed is controlled by starting the red zone of the tachometer at different engine speeds ranging from 3700 r/min to 7300
r/min depending on the engine coolant temperature.
Before driving under extremely high load conditions, make sure to sufficiently warm up the engine.
■Instrument panel brightness adjustment
The brightness of the instrument panel lights is automatically adjusted based on the light sensor detecting how bright the sur-
roundings are.
■Outside temperature display
●In the following situations, the correct
outside temperature may not be dis- played, or the display may take longer
than normal to change. • When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has changed suddenly (at the entrance/exit of a garage, tunnel, etc.)
●When “- -” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Pop-up display
●In some situations, such as when a switch operation is performed, a pop-up display
will be temporarily displayed on the multi-information display.
●Some pop-up displays can be set on/off. ( P.97)
A
B

91
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
■Liquid crystal display
Small spots or light spots may appear on the
display. This phenomen on is characteristic of liquid crystal displays, and there is no problem continuing to use the display.
■Customization
The meter display can be customized on the multi-information display. ( P.423)
The odometer and trip meter displays
can be switched. When the trip meter
is displayed, pressing and holding the
button will reset the trip meter.
The brightness of the instrument panel
lights can be adjusted.
1 Darker
2 Brighter
■Instrument panel brightness adjustment
The instrument panel brightness levels when the tail lights are on and off can be adjusted individually. However, when the
surroundings are bright (daytime, etc.), turning on the tail lights will not change the instrument panel brightness.
The display can be switched between
the center and side positions.
NOTICE
■To prevent damage to the engine and its components
●Do not let the indicator of the tachom-eter enter the red zone, as it rep-
resents the engine speed range which exceeds the maximum safe engine speed.
●In the following situations, the engine
may be overheating. In this case, immediately stop the vehicle in a safe place, and check the engine after it has
cooled completely. ( P.400, 403)
• The engine coolant temperature gauge is in the red zone (H).
• LC500: The engine oil temperature gauge is in the red zone (H).
Changing between the odome-
ter and trip meter
Changing the instrument panel
light brightness
Changing the display

97
2
-$@-$I@0.@0.&@ &&

2-1. Instrument cluster
Vehicle status information and indicators
■Eco Driving Indicator Light
(LC500)
Select to activate/deactivate the Eco
Driving Indicator Light.
■EV indicator (LC500h)
Select to activate/deactivate the EV
indicator.
■Drive information 1/Drive infor-
mation 2
Select up to 2 items that will be dis-
played on the “Drive Info 1” screen and
“Drive Info 2” screen respectively.
( P.94)
■Pop-up display
Select to set the following pop-up dis-
plays, which may appear in some situa-
tions, on/off.
• Route guidance display of the navi-
gation system-linked system (if
equipped)
• Making call display of the hands-
free phone system
• Audio system operation display
• Instrument panel brightness adjust-
ment display
■Ring position memory
Select to change the meter ring posi-
tion when the engine is
started.
The position before the engine system> is stopped or the center posi-
tion can be selected.
■Accent color
Select to change the accent color on
the screen, such as the cursor color.
■Rev indicator
Select to set the rev indicator on/off.
When set to on, proceed to select the
engine speed at which the rev indicator
will be displayed.
■Rev peak
Select to set the rev peak on/off.
■Clock
Select to switch between 24-hour dis-
play and 12-hour display.
■Initialization
Select to reset the meter display set-
tings.
■Suspension of the settings display
In the following situations, operation of the
settings display will be temporarily sus- pended.
●When a warning message appears on the multi-information display
●When the vehicle begins to move
■Customization
The settings can be changed on of the
multi-information display.
●Settings of the driving assist systems ( P.423)
●Vehicle settings (P.100, 335, 337, 423)

125
3
-$@-$I@0.@0.&@ &&

3-2. Opening, closing and locking the doors and trunk
Before driving
• The electronic key is near the ground or in a high place, or too close to the center of the rear bumper when the trunk is
opened. • The electronic key is on the instrument panel, rear package tray or floor, or in the
door pockets or glove box when the engine is started or engine switch modes are
changed.
●Do not leave the electronic key on top of
the instrument panel or near the door pockets when exiting the vehicle. Depending on the radio wave reception
conditions, it may be detected by the antenna outside the cabin and the doors will become lockable from the outside,
possibly trapping the electronic key inside the vehicle.
●As long as the electronic key is within the effective range, the doors may be locked or unlocked by anyone. However, only
the doors detecting the electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start the engine if the electronic
key is near the window.
●The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car
wash, when the electronic key is within the effective range. (The doors will auto- matically be locked after approximately
30 seconds if the doors are not opened and closed.)
●If the wireless remote control is used to lock the doors when the electronic key is near the vehicle, there is a possibility that
the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)
●If the door handle becomes wet while the electronic key is within the effective
range, the door may lock and unlock repeatedly. In this case, follow the follow-ing correction procedures to wash the
vehicle: • Place the electronic key in a location 2 m (6 ft.) or more away from the vehicle.
(Take care to ensure that the key is not stolen.)• Set the electronic key to battery-saving
mode to disable the smart entry & start system. ( P.124)
●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on
the multi-information display and a buzzer will sound outside the vehicle. To turn off the alarm, lock both side doors.
●If an outside door handle is not retracted during a car wash, a door may be opened
or an outside door handle may be dam- aged. Make sure that the outside door handles are retracted before using the
car wash.
●A sudden handle operation or a handle
operation immediately after entering the effective range may prevent the doors from being unlocked. Touch the door
unlock sensor and check that the doors are unlocked before pulling the door handle again.
●Unlocking the vehicle may take more time if another electronic key is within the
effective range.
■When the vehicle is not driven for extended periods
●To prevent theft of the vehicle, do not leave the electronic key within 2 m (6 ft.)
of the vehicle.
●The smart entry & start system can be
deactivated in advance.
■To operate the system properly
●Make sure to carry the electronic key
when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the out-
side of the vehicle. Depending on the position and holding condition of the electronic key, the key
may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door
lock prevention function may not oper- ate.)
●Do not leave the electronic key inside the