2018 Lexus LC500 brakes

240
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
1Press the cruise control main switch
to activate the cruise control.
Cruise control indicator will come on. Press the switch again to deactivate the
cruise control.
2 Accelerate or decelerate the vehi-
cle to the desired speed, and press
the -/SET switch to set the speed.
Cruise control “SET” indicator will come
on. The vehicle speed at the moment the switch is released becomes the set speed.
To change the set speed, press the
+/RES or -/SET switch until the
desired set speed is obtained.
1 Increases the speed
2 Decreases the speed
Fine adjustment: Press the switch in the
desired direction.
Large adjustment: Press and hold switch.
The set speed will be increased or
decreased as follows:
Fine adjustment: By approximately 1 km/h
(0.6 mph) each time the switch is pressed.
Large adjustment: The set speed can be
increased or decreased continually until
the switch is released.
1 Pressing the cancel switch cancels
the constant speed control.
The speed setting is also canceled when
the brakes are applied.
2 Pressing the +/RES switch resumes
the constant speed control.
Setting the vehicle speed
Adjusting the set speed
Canceling and resuming the
constant speed control

245
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
• When the Lexus parking assist-sensor is turned off once and turned on again• When the engine switch
is turned off once and turned to IGNI- TION ON mode again
■If “Clean Parking Assist Sensor” is dis-played on the multi-information display
A sensor may be dirty or covered with snow or ice. In such cases, if it is removed from
the sensor, the system should return to nor- mal.
Also, due to the sensor being frozen at low temperatures, a malfunction display may appear or an obstacle may not be detected.
If the sensor thaws out, the system should return to normal.
■If “Parking Assist Malfunction” or “Park-ing Assist Malfunction Visit Your
Dealer” is displayed on the multi-infor- mation display
There is a malfunction and the device may not be working properly.
Have the vehicle inspected by any autho- rized Lexus retailer or Lexus authorized repairer, or any reliable repairer.
■Sensor detection information
●The sensor’s detection areas are limited
to the areas around the vehicle’s front and rear bumpers.
●Certain vehicle conditions and the sur-rounding environment may affect the ability of the sensor to correctly detect
obstacles. Particular instances where this may occur are listed below.• There is dirt, snow or ice on the sensor.
(Wiping the sensors will resolve this problem.)• The sensor is frozen. (Thawing the area
will resolve this problem.)
In especially cold weather, if a sensor is fro-
zen the screen may show an abnormal dis-
play, or obstacles may not be detected.
• The sensor is covered in any way.
• The vehicle is leaning considerably to one side.• On an extremely bumpy road, on an
incline, on grav el, or on grass. • The vicinity of the vehicle is noisy due to
vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.
• There is another vehicle equipped with parking assist sensor in the vicinity.• The sensor is splashed with water or
heavy rain. • The vehicle is equipped with a fender pole or wireless antenna.
• Towing eyelets are installed. • The bumper or sensor receives a strong impact.
• The vehicle is approaching a tall or curved curb.• In harsh sunlight or intense cold weather.
• The area directly under the bumpers is not detected.• If obstacles draw too close to the sensor.
• A non-genuine Lexus suspension (low- ered suspension etc.) is installed.• People may not be detected if they are
wearing certain types of clothing.
In addition to the examples above, there are
instances in which, because of their shape,
signs and other objects may be judged by
the sensor to be closer than they are.
●The shape of the obstacle may prevent the sensor from detecting it. Pay particu-
lar attention to the following obstacles: • Wires, fences, ropes, etc.• Cotton, snow and other materials that
absorb sound waves • Sharply-angled objects•Low obstacles
• Tall obstacles with upper sections pro- jecting outwards in the direction of your vehicle
●The following situations may occur during use.
• Depending on the shape of the obstacle and other factors, the detection distance may shorten, or detection may be impos-
sible. • Obstacles may not be detected if they are too close to the sensor.
• There will be a short delay between obstacle detection and display. Even at slow speeds, there is a possibility that the
obstacle will come within the sensor’s detection areas before the display is shown and the warning beep sounds.

262
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
■ECB (Electronically Controlled
Brake System)
The electronically controlled system
generates braking force correspond-
ing to the brake operation
■ABS (Anti-lock Brake System)
Helps to prevent wheel lock when the
brakes are applied suddenly, or if the
brakes are applied while driving on a
slippery road surface
■Brake assist
Generates an increased level of brak-
ing force after the brake pedal is
depressed when the system detects a
panic stop situation
■VSC (Vehicle Stability Control)
Helps the driver to control skidding
when swerving suddenly or turning on
slippery road surfaces
■Secondary Collision Brake (if
equipped)
When the airbag sensor detects a colli-
sion, the brakes and brake lights are
automatically controlled to reduce the
vehicle speed and that helps reduce
the possibility of further damage due to
a secondary collision.
■TRC (Traction Control)
Helps to maintain drive power and pre-
vent the drive wheels from spinning
when starting the vehicle or accelerat-
ing on slippery roads
■Hill-start assist control
Helps to reduce the backward move-
ment of the vehicle when starting on an
uphill
■VGRS (Variable Gear Ratio Steer-
ing) (if equipped)
Adjusts the front wheel turning angle in
accordance with the vehicle speed and
steering wheel movement
■DRS (Dynamic Rear Steering) (if
equipped)
Contributes to the turning characteris-
tics and responsiveness of the vehicle
by slightly adjusting the rear wheel
angle of the vehicle in accordance with
steering wheel movement.
■EPS (Electric Power Steering)
Employs an electric motor to reduce
the amount of effort needed to turn the
steering wheel
■AVS (Adaptive Variable Suspen-
sion System)
By independently controlling the
damping force of the shock absorbers
for each of the 4 wheels according to
Driving assist systems
To keep driving safety and perfor-
mance, the following systems oper-
ate automatically in response to
various driving situations. Be aware,
however, that these systems are
supplementary and should not be
relied upon too heavily when oper-
ating the vehicle.
Summary of the driving assist
systems

263
4
-$@-$I@0.@0.&@ &&

4-5. Using the driving support systems
Driving
the road and driving conditions, this
system helps riding comfort with supe-
rior vehicle stability, and helps good
vehicle posture
Also, the damping force changes
depending on the selected driving
mode. ( P.242)
■LDH (Lexus Dynamic Handling
system) (if equipped)
Provides integrated control of the
VGRS, DRS and EPS. Contributes to
turning characteristics at low speeds,
responsiveness at medium speeds and
safety at high speeds by controlling the
steering angle of the front and rear
wheels in accordance with the steering
wheel operation and vehicle speed.
■VDIM (Vehicle Dynamics Inte-
grated Management)
Provides integrated control of the
ABS, brake assist, TRC, VSC, hill-start
assist control, EPS, VGRS (if
equipped) and DRS (if equipped) sys-
tems
Helps to maintain vehicle stability when
swerving on slippery road surfaces by
controlling the brakes, engine system> output, steering assist (if
equipped), and steering ratio (if
equipped)
■Emergency brake signal
When the brakes are applied suddenly,
the stop lights automatically flash to
alert the vehicle behind
■When the TRC/VSC/ABS systems are operating
The slip indicator light will flash while the TRC/VSC/ABS systems are operating.
■Disabling the TRC system
If the vehicle gets stuck in mud, dirt or snow,
the TRC system may reduce power from the engine to the wheels.
Pressing the switch to turn the sys-
tem off may make it easier for you to rock
the vehicle in order to free it.
To turn the TRC system off, quickly press
and release the switch.
The “Traction Control Turned Off” will be
shown on the multi-information display.
Press the switch again to turn the sys-
tem back on.
■Disabling both TRC and VSC systems
To turn the TRC and VSC systems off, press
and hold the switch for more than 3
seconds while the vehicle is stopped.
The VSC OFF indicator light will come on and the “Traction Cont rol Turned Off” will
be shown on the multi-information display.*

267
4
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Driving
4-6.Driving tips
When using Eco drive mode, the
torque corresponding to the accelera-
tor pedal depression amount can be
generated more smoothly than it is in
normal conditions. In addition, the
operation of the air conditioning sys-
tem (heating/cooling) will be mini-
mized, improving the fuel economy.
( P.242)
The Eco-friendly driving is possible by
keeping the indicate of Hybrid System
Indicator within Eco area. ( P.86)
Shift the shift position to D when
stopped at a traffic light, or driving in
heavy traffic etc. Shift the shift position
to P when parking. When using the N
position, there is no positive effect on
fuel consumption. In the N position, the
gasoline engine operates but electric-
ity cannot be generated. Also, when
using the air conditioning system, etc.,
the hybrid battery (traction battery)
power is consumed.
 Drive your vehicle smoothly. Avoid
abrupt acceleration and decelera-
tion. Gradual acceleration and
deceleration will make more effec-
tive use of the electric motor (trac-
tion motor) without having to use
gasoline engine power.
 Avoid repeated acceleration.
Repeated acceleration consumes
hybrid battery (traction battery)
power, resulting in poor fuel con-
sumption. Battery power can be
restored by driving with the acceler-
ator pedal slightly released.
Make sure to operate the brakes gently
and in a timely manner. A greater
amount of electrical energy can be
regenerated when slowing down.
Repeated acceleration and decelera-
tion, as well as long waits at traffic
lights, will lead to bad fuel economy.
Check traffic reports before leaving
and avoid delays as much as possible.
When driving in a traffic jam, gently
release the brake pedal to allow the
vehicle to move forward slightly while
avoiding overuse of the accelerator
pedal. Doing so can help control
excessive gasoline consumption.
Hybrid vehicle driving tips
(LC500h)
For economical and ecological
driving, pay attention to the follow-
ing points:
Using Eco drive mode
Use of Hybrid System Indicator
Changing the shift position
Accelerator pedal/brake pedal
operation
When braking
Delays

268
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Control and maintain the vehicle at a
constant speed. Before stopping at a
toll booth or similar, allow plenty of
time to release the accelerator and
gently apply the brakes. A greater
amount of electrical energy can be
regenerated when slowing down.
Use the air conditioning only when
necessary. Doing so can help reduce
excessive gasoline consumption.
In summer: When the ambient tem-
perature is high, use the recirculated
air mode. Doing so will help to reduce
the burden on the air conditioning sys-
tem and reduce fuel consumption as
well.
In winter: Because the gasoline engine
will not automatically cut out until it and
the interior of the vehicle are warm, it
will consume fuel. Also, fuel consump-
tion can be improved by avoiding over-
use of the heater.
Make sure to check the tire inflation
pressure frequently. Improper tire infla-
tion pressure can cause poor fuel
economy.
Also, as snow tires can cause large
amounts of friction, their use on dry
roads can lead to poor fuel economy.
Use tires that are appropriate for the
season.
Carrying heavy luggage will lead to
poor fuel economy. Avoid carrying
unnecessary luggage. Installing a large
roof rack will also cause poor fuel
economy.
Since the gasoline engine starts up and
cuts out automatically when cold,
warming up the engine is unnecessary.
Moreover, frequently driving short dis-
tances will cause the engine to repeat-
edly warm up, which can lead to excess
fuel consumption.
Highway driving
Air conditioning
Checking tire inflation pressure
Luggage
Warming up before driving

270
-$@-$I@0.@0.&@ &&

4-6. Driving tips
Perform the following according to the
driving conditions:
 Do not try to forcibly open a window
or move a wiper that is frozen. Pour
warm water over the frozen area to
melt the ice. Wipe away the water
immediately to prevent it from
freezing.
 When the outside door handle is
frozen, unlock the doors using the
wireless remote control. If the out-
side door handles remain retracted
and do not move even if the doors
are unlocked using the wireless
remote control, pour warm water
over the frozen area to melt the ice
and wipe away the water immedi-
ately to prevent it from freezing. The
outside door handle may not retract
due to ice, however, the outside
door handle will return to the nor-
mal position after the ice melts.
 To ensure proper operation of the
climate control system fan, remove
any snow that has accumulated on
the air inlet vents in front of the
windshield.
 Check for and remove any excess
ice or snow that may have accumu-
lated on the exterior lights, vehicle’s
roof, chassis, around the tires or on
the brakes.
 Remove any snow or mud from the
bottom of your shoes before getting
in the vehicle.
■To protect windshield wipers
 P.198
Accelerate the vehicle slowly, keep a
safe distance between you and the
vehicle ahead, and drive at a reduced
speed suitable to road conditions.
Park the vehicle and shift the shift posi-
tion to P without setting the parking
brake. The parking brake may freeze
up, preventing it from being released. If
the vehicle is parked without setting
the parking brake, make sure to block
the wheels.
Failure to do so may be dangerous
because it may cause the vehicle to
move unexpectedly, possibly leading to
an accident.
NOTICE
■Repairing or replacing snow tires
Request repairs or re placement of snow
tires from any authorized Lexus retailer or Lexus authorized repairer, or any reli-able repairer.
This is because the removal and attach- ment of snow tires affects the operation
of the tire pressure warning valves and transmitters.
Before driving the vehicle
When driving the vehicle
When parking the vehicle

294
-$@-$I@0.@0.&@ &&

5-5. Using the storage features
1Using with half-open: Slide the
armrest as far back while pressing
the button.
Press the button to close.
2 Using with fully open: Lift the arm-
rest while pulling the knob.
■Console box light
The console box light turns on when the tail lights are on.
■Using the auxiliary box
Do not place cups, beverage cans, etc. in the auxiliary box.
To open, press down and release the
cup holder lid.
Console box/auxiliary box
WARNING
■When closing the console box
Take care to prevent your fingers etc. from being caught.
NOTICE
■To prevent damage to the console box
●Do not pull the knob while sliding the armrest.
●Do not apply excessive force to the armrest.
Cup holder
WARNING
■Items unsuitable for the cup holder
Do not place anything other than a cup
or beverage can in the cup holder. Even when the lid is closed, items must not be stored in the cup holder.
Other items may be thrown out of the holder in the event of an accident or sud-den braking, causing injury. If possible,
cover hot drinks to prevent burns.
NOTICE
■To prevent damage to the cup holder and air conditioning control switches
●Do not apply excessive force to the cup holder.
●Take care when placing a tall bottle in the cup holder. When the bottle is
taken out or the brakes are suddenly applied, the bottle may hit the air con-ditioning control switches, causing
damage to the switches or parts of the air conditioning system.