2018 Lexus LC500 steering wheel

198
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
1Select “Transmit volume” on the sub
menu.
2 Select the desired level for the
transmit volume.
3 Press the button on the
Remote Touch to display previous
screen.
●The sound quality of the voice heard from the other party’s speaker may be nega-
tively impacted.
●“Transmit volume” is dimmed when mute
is on.
When a call is interrupted by a third
party while talking, the incoming
screen is displayed.
The incoming screen can also be dis-
played on the side display.
1 Select “Answer” or press the
switch on the steering wheel to
start talking with the other party.
 To refuse to receive the call: Select
“Decline”.
 Each time “Swap calls” is selected,
the party who is on hold will be
switched.
●This function may not be available
depending on the type of cellular phone.
●This screen can be displayed on the main
display or side display.
 When there are no calls on hold
during a call: “Hold” is displayed.
When selected, the current call is
placed on hold.
 When there is no current call, but
there is a call on hold: “Activate” is
displayed. When selected, the sys-
tem switches to the call that was on
hold.
 When there is another call on hold
during a call: “Swap calls” is dis-
played. When selected, the current
call is placed on hold, and the sys-
tem switches to the call that was on
hold.
●This function may not be available depending on the type of cellular phone.
●This screen can be di splayed on the main display or side display.
Transmit volume setting
Incoming call waiting
Switching calls whil e a call is in
progress

200
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
be set to “Full screen” on “Incoming SMS/MMS display” and “Incoming E-mail display”. ( P.205) Default setting is
“Drop-down”.
●Depending on the cellular phone used
for receiving messages, or its registration status with the system, some information may not be displayed.
●The pop up screen is separately available for incoming e-mail and SMS/MMS
messages under the following conditions:
E-mail:
• “E-mail notification pop-up” is set to on.
( P.205)
SMS/MMS:
• “SMS/MMS notification pop-up” is set to
on. ( P.205)
1Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select “Message” on the sub menu.
4 Select a desired account name that
is displayed on the left side of
screen.
5 Select the desired message from
the list.
6 Check that the message is dis-
played.
Select “Mark unread” or “Mark
read” to mark e-mail unread or
read on the message screen.
This function is available when
“Update message read status on
phone” is set to on. ( P.211)
When the text message type is
SMS, it is not displayed.
Select to reply to the message.
( P.201)
Select to display the previous or
next message.
Select to have messages read out.
To cancel this function, select .
When “Automatic message read-
out” is set to on, messages will be
automatically read out. ( P.211)
Select to make a call to the sender.
●Depending on the type of Bluetooth® phone being connected, it may be neces-sary to perform additional steps on the
phone.
●Messages are displayed in the appropri-
ate connected Bluetooth® phone’s regis- tered mail address folder. Select the desired folder name to be displayed.
●Turn the “PWR·VOL” knob, or use the volume control switch on the steering
wheel to adjust the message read out vol- ume.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select “Message” on the sub menu.
Checking received messages
A
Checking sent messages
B
C
D
E

202
-$@-$I@/BWJ@0.&@ &&

7-1. Phone operation (Hands-free system for cellular phones)
played.
8 Check that a confirmation screen is
displayed when the operation is
complete.
 If an error message is displayed, fol-
low the guidance on the screen to
try again.
■Editing quick reply messages
This operation cannot be performed
while driving.
1 Select “Quick message”.
2 Select corresponding to the
desired message to edit.
3 Select “OK” when editing is com-
pleted.
●To reset the edited quick reply messages, select “Default”.
●Quick message #1 (“I am driving and will arrive in approximately [##] minutes.”):
This message cannot be edited and will automatically fill in [##] with the naviga-tion calculated estimated time of arrival
on the confirm message screen. If there are waypoints set, [##] to the next waypoint will be shown.
If there is no route currently set in the navigation system, Quick message #1 cannot be selected.
●Depending on the cellular phone used for receiving messages, reply function
may not be used.
Calls can be made to an e-
mail/SMS/MMS message sender’s
phone number.
This operation can be performed while
driving.
■Calling from e-mail/SMS/MMS
message display
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select “Message” on the sub menu.
4 Select the desired message.
5 Select , or press the switch
on the steering wheel.
 If there are 2 or more phone num-
bers, select the desired number.
6 Check that the call screen is dis-
played.
■Calling from a number within a
message
Calls can be made to a number identi-
fied in a message’s text area in blue
font.
This operation cannot be performed
while driving.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Phone”.
3 Select “Message” on the sub menu.
4 Select the desired message.
5 Select the text area.
Calling the message sender