2018 KIA STONIC fuel

Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these ma‐ terials are not removed, accelerated
rusting can occur on underbody parts
such as the fuel lines, frame, floor pan and exhaust system, even though they
have been treated with rust protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or cold water once a month, after off-
road driving and at the end of each
winter. Pay special attention to these areas because it is difficult to see all
the mud and dirt. It will do more harm
than good to wet down the road grime without removing it. The lower edges
of the doors, rocker panels, and frame
members have drain holes that should not clog with dirt; trapped water in
these areas can cause rusting.
WARNING
After washing the vehicle, test thebrakes while driving slowly to see ifthey have been affected by water. Ifbraking performance is impaired, dry
(Continued)
(Continued)
the brakes by applying them lightlywhile maintaining a slow forwardspeed.
Aluminum wheel maintenance
The aluminum wheels are coated with a
clear protective finish. • Do not use any abrasive cleaner, pol‐ ishing compound, solvent, or wirebrushes on aluminum wheels. They
may scratch or damage the finish.
• Clean the wheel when it has cooled.
• Use only a mild soap or neutral deter‐ gent, and rinse thoroughly with wa‐
ter. Also, be sure to clean the wheels
after driving on salted roads. This helps prevent corrosion.
• Avoid washing the wheels with high- speed car wash brushes.
• Do not use any alkaline or acid deter‐ gent. It may damage and corrode the
aluminum wheels coated with a clear
protective finish.
Corrosion protection
Protecting your vehicle from corrosion
By using the most advanced design and
construction practices to combat corro‐ sion, we produce vehicles of the highest
quality. However, this is only part of
the job. To achieve the long-term cor‐ rosion resistance your vehicle can deliv‐
er, the owner's cooperation and assis‐
tance is also required.
Common causes of corrosion
The most common causes of corrosion on your vehicle are: • Road salt, dirt and moisture that is allowed to accumulate underneath
the vehicle.
• Removal of paint or protective coat‐ ings by stones, gravel, abrasion or
minor scrapes and dents which leave unprotected metal exposed to corro‐
sion.
High-corrosion areas
If you live in an area where your vehicle
is regularly exposed to corrosive mate‐ rials, corrosion protection is particularly
important. Some of the common cau‐
ses of accelerated corrosion are road salts, dust control chemicals, ocean air
and industrial pollution.
Maintenance
8-130

EMISSION CONTROL SYSTEM (IF EQUIPPED)
The emission control system of your vehicle is covered by a written limited
warranty. Please see the warranty in‐
formation contained in the Warranty & Maintenance book in your vehicle.
Your vehicle is equipped with an emis‐
sion control system to meet all applica‐
ble emission regulations.
There are three emission control sys‐ tems, as follows. 1. Crankcase emission control system
2. Evaporative emission control sys‐ tem
3. Exhaust emission control system
In order to assure the proper function
of the emission control systems, have
your vehicle inspected and maintained by a professional workshop in accord‐
ance with the maintenance schedule in
this manual. Kia recommends to visit an
authorized Kia dealer/service partner.
Caution for the Inspection and Mainte‐nance Test (With Electronic StabilityControl (ESC) system)
•To prevent the vehicle from misfiringduring dynamometer testing, turnthe Electronic Stability Control (ESC)system off by pressing the ESCswitch. •
After dynamometer testing is com‐pleted, turn the ESC system back onby pressing the ESC switch again.
1. Crankcase emission control
system
The positive crankcase ventilation sys‐
tem is employed to prevent air pollu‐ tion caused by blow-by gases being
emitted from the crankcase.
This system supplies fresh filtered air
to the crankcase through the air intake hose. Inside the crankcase, the fresh air
mixes with blow-by gases, which then
pass through the PCV valve into the in‐ duction system.
2. Evaporative emission control
system
The Evaporative Emission Control Sys‐
tem is designed to prevent fuel vapors from escaping into the atmosphere.
Canister
Fuel vapors generated inside the fuel
tank are absorbed and stored in the on‐ board canister. When the engine is run‐
ning, the fuel vapors absorbed in the
canister are drawn into the surge tank through the purge control solenoid
valve.
Purge Control Solenoid Valve (PCSV)
The purge control solenoid valve is con‐
trolled by the Engine Control Module (ECM); when the engine coolant tem‐
perature is low during idling, the PCSV
closes so that evaporated fuel is not taken into the engine. After the engine
warms up during ordinary driving, the
PCSV opens to introduce evaporated fuel to the engine.
3. Exhaust emission control
system
The Exhaust Emission Control System
is a highly effective system which con‐
trols exhaust emissions while maintain‐
ing good vehicle performance.
Vehicle modifications
This vehicle should not be modified.
Modification of your vehicle could affect
its performance, safety or durability and may even violate governmental
safety and emissions regulations.
In addition, damage or performance
problems resulting from any modifica‐ tion may not be covered under warran‐
ty.
Maintenance
8-134

• If you use unauthorized electronicdevices, it may cause the vehicle to
operate abnormally, wire damage, battery discharge and fire. For your
safety, do not use unauthorized elec‐
tronic devices.
Engine exhaust gas precautions
(carbon monoxide)
• Carbon monoxide can be present with other exhaust fumes. Therefore, if
you smell exhaust fumes of any kind inside your vehicle, have it inspected
and repaired immediately. If you ever
suspect exhaust fumes are coming
into your vehicle, drive it only with all
the windows fully open. Have your vehicle checked and repaired immedi‐
ately.
WARNING
nExhaust
Engine exhaust gases contain carbonmonoxide (CO). Though colorless andodorless, it is dangerous and couldbe lethal if inhaled. Follow the in‐structions on this page to avoid COpoisoning.
• Do not operate the engine in confined or closed areas (such as garages) any
more than what is necessary to move the vehicle in or out of the area.
• When the vehicle is stopped in an open area for more than a short time
with the engine running, adjust the
ventilation system (as needed) to
draw outside air into the vehicle.
• Never sit in a parked or stopped vehi‐ cle for any extended time with the
engine running.
• When the engine stalls or fails to start, excessive attempts to restart
the engine may cause damage to the
emission control system.
Operating precautions for catalytic
converters (if equipped)
WARNING
nFire
(Continued)
(Continued)
•A hot exhaust system can igniteflammable items under your vehi‐cle. Do not park the vehicle over ornear flammable objects, such asgrass, vegetation, paper, leaves,etc.
•The exhaust system and catalyticsystem are very hot while the en‐gine is running or immediately af‐ter the engine is turned off. Keepaway from the exhaust systemand catalytic, you may get burned.Also, do not remove the heat sinkaround the exhaust system, donot seal the bottom of the vehicleor do not coat the vehicle for cor‐rosion control. It may present afire risk under certain conditions.
Your vehicle is equipped with a catalytic
converter emission control device.
Therefore, the following precautions must be observed: • Make sure to refuel your vehicle ac‐ cording to the L

• Do not misuse or abuse the engine.Examples of misuse are coasting with
the ignition off and descending steep grades in gear with the ignition off.
• Do not operate the engine at high idle speed for extended periods (5 mi‐
nutes or more).
• Do not modify or tamper with any part of the engine or emission control
system. All inspections and adjust‐ ments must be made by a professio‐
nal workshop. Kia recommends to
visit an authorized Kia dealer/service
center.
• Avoid driving with an extremely low fuel level. Running out of fuel couldcause the engine to misfire, damag‐
ing the catalytic converter.
Failure to observe these precautions
could result in damage to the catalytic converter and to your vehicle.
Additionally, such actions could void
your warranties.
Diesel particulate filter (if
equipped)
The Diesel Particulate Filter (DPF) sys‐
tem removes the soot in the exhaust gas. Unlike a disposable air filter, the DPF
system automatically burns (oxidizes)
and removes the accumulated soot ac‐ cording to the driving condition. In other
words, the active burning by engine
control system and high exhaust gas temperature caused by normal/high
driving condition burns and removes
the accumulated soot.
However, if the vehicle continues to be driven at repeated short distance or
driven at low speed for a long time, the
accumulated soot may not be auto‐ matically removed because of low ex‐
haust gas temperature. More than a
certain amount of soot deposited, the malfunction indicator light (
) illumi‐
nates.
When the malfunction indicator light
blinks, it may stop blinking by driving
the vehicle at more than 60 km/h (37 mph) or at more than second gear
with 1500 ~ 2500 engine rpm for a cer‐
tain time (for about 25 minutes).
If the malfunction indicator light (
)
continues to be blinked or the warning
massage "Check exhaust system" illu‐ minates in spite of the procedure, visit
a professional workshop and check the
DPF system. Kia recommends to visit an authorized Kia dealer/service part‐
ner. If you continue to drive with the mal‐
function indicator light blinking for a long time, the DPF system can be dam‐
aged and fuel consumption can be wor‐
sen.
CAUTION
Diesel Fuel (if equipped with DPF)It is recommended to use the regula‐ted automotive diesel fuel for dieselvehicle equipped with the DPF sys‐tem.If you use diesel fuel including highsulfur (more than 50 ppm sulfur)and unspecified additives, it cancause the DPF system to be dam‐aged and white smoke can be emit‐ted.
Lean NOx trap (if equipped)
The Lean NOx Trap (LNT) system re‐
moves the nitrogen oxide in the ex‐ haust gas. The smell can occur in the
exhaust gas depending on the quality
of the fuel and it can degrade NOx re‐ duction performance, please use the
regulated automotive diesel fuel.
Maintenance
8-136

RECOMMENDED LUBRICANTS AND CAPACITIES
To help achieve proper engine and powertrain performance and durability, use only lubricants of the proper quality. The cor‐
rect lubricants also help promote engine efficiency that results in improved fuel economy.
These lubricants and fluids are recommended for use in your vehicle.
LubricantVolumeClassification
Engine oil *1
*2
(drain and refill)
Recommends
Gasoline Engine 1.0L
3.6
l (3.8 US
qt.) ACEA A5/B5
1.2L 3.5
l (3.7 US
qt.) API service SM, ILSAC GF4 or above, ACEA A5/B5
*3
API SN, ACEA C2 *4
1.4L 3.6
l (3.8 US
qt.) API service SM, ILSAC GF4 or above, ACEAA5/B5
*3
API SN, ACEA C2 *4
Diesel En‐ gine 1.4L /
1.6L with
DPF *5 5.3
l (5.6 US
qt.) ACEA C2 or C3
Without DPF *5 5.3
l (5.6 US
qt.) ACEA C3 or C2 or A3/B4
Manual transaxle fluid Gasoline Engine 1.2L
1.5 ~ 1.6
l (1.4 ~
1.5 US qt.) API Service GL-4 SAE 70W
- HK SYN MTF 70W
- SPIRAX S6 GHME 70W MTF - GS MTF HD 70W
1.0L/
1.4L 1.6 ~ 1.7
l (1.5 ~
1.6 US qt.)
Diesel Engine 1.4L 1.7 ~ 1.8
l (1.6 ~
1.7 US qt.)
Automatic transaxlefluid Gasoline Engine 1.4L 6.8
l (7.2 US
qt.) ATF SP-III (Recommended DIAMOND, SK)


9-13
9
Specifications & Consumer information

LubricantVolumeClassification
Coolant Gasoline Engine1.0L
5.5
l (5.8 US
qt.)
Mixture of antifreeze and water (Ethylene glycolbase coolant for aluminum radiator)
1.2L
5.1
l (5.4 US
qt.)
1.4L MT
5.1
l (5.4 US
qt.)
AT 5.5
l (5.8 US
qt.)
Diesel En‐gine 1.4L/1.6L6.4
l (6.8 US
qt.)
Brake / clutch fluid 0.7 ~ 0.8
l (0.7 ~
0.8 US qt.) FMVSS116 DOT-3 or DOT-4
Fuel 45
l (11.9 US
gal.) -
*1
Refer to L

Recommended SAE viscosity number
CAUTION
Always be sure to clean the area around any filler plug, drain plug, or dipstick before checking or draining any lubricant.This is especially important in dusty or sandy areas and when the vehicle is used on unpaved roads. Cleaning the plug anddipstick areas will prevent dirt and grit from entering the engine and other mechanisms that could be damaged.
Engine oil viscosity (thickness) has an effect on fuel economy and cold weather operating (engine start and engine oil flowabil‐
ity). Lower viscosity engine oils can provide better fuel economy and cold weather performance, however, higher viscosity en‐ gine oils are required for satisfactory lubrication in hot weather. Using oils of any viscosity other than those recommended
could result in engine damage.
When choosing an oil, consider the range of temperature your vehicle will be operated in before the next oil change. Proceed to select the recommended oil viscosity from the chart.

9-15
9
Specifications & Consumer information

Jack and tools.............................................................. 7-12
Tire mobility kit........................................................... 7-20
Floor mat anchor(s)......................................................4-131 Fluid
Automatic transaxle ýluid..........................................8-53
Washer ýluid.................................................................8-55
Foldinþ the rear seat...................................................... 3-10
Front seat adjustment................................................... 3-05
Fuel ýiller lid...................................................................... 4-30
Fuel ýilter.......................................................................... 8-57
Fuel þauþe........................................................................ 4-50
Fuel requirements...........................................................1-03
Fuses................................................................................. 8-77
Fuse/relay panel description.......................... 8-82,8-83
Instrument panel ýuse............................................... 8-79
Multi ýuse..................................................................... 8-81
G
Gauþes Enþine temperature þauþe....................................... 4-49
Fuel þauþe....................................................................4-50
Glove box........................................................................ 4-122
H
Hazardous drivinþ conditions........................................ 6-78
Headliþht bulb replacement........................................ 8-104
Headrest (ýront).............................................................. 3-06
Headrest (rear)................................................................ 3-09
Heated steerinþ whee.................................................... 4-39
Hiþhway drivinþ............................................................... 6-81
Hood.................................................................................. 4-28
Horn...................................................................................4-39
How to use this manual................................................. 1-02
I
Immobilizer system........................................................ 4-05
In case oý an emerþency while drivinþ........................ 7-03
Inside rearview mirror.................................................... 4-41
Instrument cluster.......................................................... 4-45 Enþine temperature þauþe....................................... 4-49
Fuel þauþe....................................................................4-50
Instrument cluster control........................................ 4-46
LCD window control....................................................4-47
Speedometer............................................................... 4-48
Tachometer................................................................. 4-49
Instrument panel ýuse................................................... 8-79
Alphabetical index
I-4 Alphabetical index