2018 KIA STONIC display
[x] Cancel search: displayPage 277 of 523
Collision warning (2nd warning)
• The warning message appears on theLCD display with a warning alarm.
• The vehicle will reduce its speed to a certain limit.- The brake activates gradually for vehicles ahead.
- The brake control activates within an arranged limit to ease the im‐
pact from a collision.
Emergency braking (3rd warning)
• The warning message appears on the LCD display with a warning alarm.
• The vehicle will reduce its speed to a certain limit.
- The brake control activates within an arranged limit to ease the im‐
pact from a collision. Maximum
brake control is activated just be‐
fore the collision.
Brake operation
• In an urgent situation, the braking system enters into the ready status
for prompt reaction against the driv‐ er’s depressing the brake pedal. • The FCA provides additional braking
power for optimum braking perform‐
ance, when the driver depresses the
brake pedal.
• The braking control is automatically deactivated, when the driver sharplydepresses the brake pedal, or when
the driver abruptly operates the
steering wheel.
• The braking control is automatically canceled, when risk factors disappear.
CAUTION
The driver should always pay greatcaution to vehicle operation, eventhough there is no warning messageor warning alarm.
WARNING
The FCA cannot avoid all collisions.The FCA might not completely stopthe vehicle before collision, due toambient, weather and road condi‐tions. The driver has the responsibili‐ty to drive safely and control the ve‐hicle.
6-55
6
Driving your vehicle
Page 282 of 523
-When the stopped vehicle in front
gets out of the lane, it may not be
recognized by your FCA. Always pay great attention.
- Recognizing the vehicle
When the vehicle in front has heavy
loading extended rearward, or when
the vehicle in front has higher ground clearance, it may induce a hazardous
situation.
Recognizing pedestrians
- The pedestrian is not fully captured
by the camera sensor, or the pedes‐
trian does not walk in the upright po‐ sition.
- The pedestrian moves very fast.
- The pedestrian abruptly appears in
front.
- The pedestrian wears clothes in the
color similar to the background.
- The outside is too bright or too dark.
- The vehicle drives at night or in the
darkness.
- There is an item similar to a person’s
body structure.
- The pedestrian is small.
- The pedestrian has impaired mobility.
- It is difficult to distinguish the pedes‐
trian from the surroundings.
- The sensor recognition is limited. -
There is a group of pedestrians.
WARNING
•Cancel the FCA in the User Set‐tings on the LCD display, beforetowing another vehicle. While tow‐ing, the brake application may ad‐versely affect your vehicle safety.
•Pay great caution to the vehicle infront, when it has heavy loadingextended rearward, or when it hashigher ground clearance.
•The sensor only detects pedes‐trian, not carts, bicycles, motorcy‐cles, luggage bags, or strollers.
•The FCA does not operate in a cer‐tain situation. Thus, never test-operate the FCA against a personor an object. It may cause a severeinjury or even death.
•When reinstalling the windshield orLane Departure Warning (LDW)camera after replacement or re‐moval, have the vehicle inspectedby a professional workshop. Kiarecommends to visit an authorizedKia dealer/service partner.
Driving your vehicle
6-60
Page 285 of 523
(Continued)
•Always check road conditions be‐cause you may not hear the warn‐ing chime because of audio and ex‐ternal conditions.
To operate the Lane Departure Warning
(LDW) System, press the switch with the ignition in the ON position. The indi‐
cator illuminates white on the cluster.
To cancel the Lane Departure Warning
(LDW) System, press Lane Departure Warning (LDW) System button again.
The indicator on the cluster will go off.
If you select trip display, the Lane De‐
parture Warning (LDW) System mode on the LCD display will appear.
If your vehicle leaves the lane when the
Lane Departure Warning (LDW) System
is operating and vehicle speed exceeds
60 km/h, the warning operates as fol‐
lows:
¥ - F G U M B O F E F Q B S U V S F X B S O J O H
¥ 3 J H I U M B O F E F Q B S U V S F X B S O J O H
1. Visual warning If you leave a lane, the lane you
cross will blink (yellow) and Lane
Departure Warning (LDW) System
indicator will blink green on LCD
during max 3 seconds.
6-63
6
Driving your vehicle
Page 288 of 523
DRIVER ATTENTION WARNING (DAW) SYSTEM (IF EQUIPPED)
The Driver Attention Warning (DAW)
system displays the condition of the
driver's fatigue level and inattentive driving practices.
System setting and activation
System setting
• The Driver Attention Warning system is set to be in the OFF position, when
your vehicle is first delivered to you from the factory.
• To turn ON the Driver Attention Warning system, turn on the engine,
and then select 'User Settings
Driving Assist Driver Attention
Warning Normal/Early' on the LCD
display.
• The driver can select the Driver At‐ tention Warning system mode.- Off: The Driver Attention Warning system is deactivated.
- Normal: The Driver Attention Warning system alerts the driver
of his/her fatigue level or inatten‐
tive driving practices.
- Early: The Driver Attention Warn‐ ing system alerts the driver of
his/her fatigue level or inattentive
driving practices faster than Nor‐mal mode. • The set-up of the Driver Attention
Warning system will be maintained,as selected, when the engine is re‐
started.
Display of the driver's attention
level
0 : # -
4 Z T U F N P G G
0 : # -
" U U F O U J W F E S J W J O H
0 : # -
* O B U U F O U J W F E S J W J O H
• The driver can monitor their driving conditions on the LCD display.
The DAW screen will appear when
you select the ASSIST mode tab (
)
on the LCD display if the system is
activated. (For more information, re‐
fer to L
Page 289 of 523
• When the driver turns on the systemwhile driving, it displays 'Last Break
time' and level.
Take a break
0 : # -
• The "Consider taking a break" mes‐ sage appears on the LCD display and
a warning sounds in order to suggest the driver to take a break, when the
driver's attention level is below 1.
• The Driver Attention Warning system does not suggest the driver to take a
break, when the total driving time is
shorter than 10 minutes.
Resetting the system
• The last break time is set to 00:00 and the driver's attention level is setto 5 (very attentive) when the driver
resets the Driver Attention Warning
system.
• The Driver Attention Warning system resets the last break time to 00:00
and the driver's attention level to 5 in the following situations. - The engine is turned OFF.
- The driver unfastens the seat belt and then opens the driver's door.
- The engine has been idled continu‐ ously over 10 minutes.
• The Driver Attention Warning system operates again, when the driver re‐
starts driving.
System standby
0 : # -
The Driver Attention Warning system
enters the ready status and displays the 'Standby' screen in the following
situations.
- The camera does not detect the
lanes.
- Driving speed remains under 60 km/h
(40 mph) or over 200 km/h
(125 mph).
6-67
6
Driving your vehicle
Page 294 of 523
0 % &
O E T U B H F
The second stage alarm will activate
when: 1. The first stage alert is on
2. The turn signal is on to change a lane
When the second stage alert is activa‐ ted, a warning light will be blinking on
the outside rearview mirror and an
alarm will sound.
If you move the turn signal switch to origin position, the second stage alert
will be deactivated.
- The second stage alarm can be deac‐
tivated. • To activate the alarm:
Go to the User Settings Mode
Sound and select Blind-Spot Collision
Warning Sound on the LCD display.
• To deactivate the alarm : Go to the User Settings Mode
Sound and deselect Blind-Spot Colli‐
sion Warning Sound on the LCD dis‐
play.
CAUTION
The alarm function helps alert thedriver. Deactivate this function onlywhen it is necessary.
Detecting sensor
0 : # %
The sensors are located inside the rear
bumper.
Always keep the rear bumper clean for the system to work properly.
Warning message
The message (L
Page 325 of 523
• If the low pressure light is illumina‐ted.
• If the suspension or ABS has been re‐ placed.
CAUTION
If the system is set without adjust‐ing tire pressure, false alarm couldoccur or the telltale will not be dis‐played even though the vehicle issignificantly under-inflated.Make sure all tires are properly ad‐justed to the recommended pressurewhen setting.If the system is not set even in re‐quired situations, false alarm couldoccur or the telltale will not be dis‐played even though the vehicle issignificantly under-inflated.The system will not be set if youpress the SET switch (2) while driv‐ing. Make sure to stop the vehicleand press the switch (2) for over 3seconds.•Be sure the tire is cold before in‐flating the pressure.A cold tire means the vehicle hasbeen sitting for 3 hours or drivenwithin 1.6km (1mile).
Indication of Low Tire Pressure
0 : # -
The () warning light will illuminate
when an under-inflated tire is indica‐ ted. In certain types, the above mes‐
sage might be displayed on the cluster.
If the warning light illuminates, reduce
your speed, avoid hard cornering and rapid braking. Have your vehicle inspec‐
ted by a professional workshop. Kia
recommends to visit an authorized Kia dealer/service partner.
Check the pressure of all tires and in‐
flate to the proper pressure according
to procedures, and if required, replace or repair the tires. If you cannot reach a close service sta‐
tion, stop the vehicle at a safe place,
check all tires and operate the TPMS setting procedure. If you are unable to
adjust the tire pressure, use the repair
tools to repair or change to spare tire and contact a professional workshop.
Kia recommends to call an authorized
Kia dealer/service partner.
You may not be able to identify low tire
pressure visually. Use precise tools to measure and adjust tire pressure.
Please note that a tire that is hot due
to prolonged driving, therefore will have high pressure. We recommend you to
measure and adjust the tire pressure
after the vehicle has driven for less than 1.6 km (1 mile) within 3 hours.
CAUTION
•The indicator may remain illumina‐ted after changing to a spare tire,because radius of spare tire is dif‐ferent. Be sure to change to a reg‐ular tire.
(Continued)
7-09
7
What to do in an emergency
Page 338 of 523
Components of the Tire Mobility Kit (TMK)1. Speed restriction label
2. Sealant bottle and label with speedrestriction
3. Filling hose from sealant bottle to wheel
4. Connectors and cable for the power outlet direct connection
5. Holder for the sealant bottle
6. Compressor
7. On/off switch
8. Pressure gauge for displaying the tire inflation pressure
9. Button for reducing tire inflation pressure
Connectors, cable and connection hose are stored in the compressor housing.
WARNING
Before using the Tire Mobility Kit,follow the instructions on the seal‐ant bottle.Remove the label with the speed re‐striction from the sealant bottle andapply it to the steering wheel.
(Continued)
What to do in an emergency
7-22