Page 116 of 523
Sliding the sunroof
To open the sunroof, push the sunroof
control lever backward.
To close the sunroof, push the sunroof control lever forward.
To open the sunroof automatically:
Pull the sunroof control lever backward
to the second detent position and then
release it. The sunroof will slide to the recommended open position (about
5 cm before the maximum slide open
position).
To stop the sunroof sliding at any point,
push the sunroof control lever momen‐ tarily.
To close the sunroof automatically:
Push the sunroof control lever forward
to the second detent position and then release it. The sunroof will automatical‐
ly close all the way.
To stop the sunroof sliding at any point,
push the sunroof control lever momen‐
tarily.
NOTICE
To reduce wind noise while driving, it
is recommended that you drive with
the sunroof slightly closed (stop the
sunroof about 5cm(2in.) before the
maximum slide open position).
WARNING
Make sure heads, other body partsor other objects are safely out of theway before closing the window toavoid injuries or vehicle damage.Objects less than 4 mm (0.16 inch) indiameter caught between the sun‐roof glass and the front windowchannel may not be detected by the
(Continued)
(Continued)
automatic reverse window and thewindow will not stop and reverse di‐rection.
Automatic reversal
If an object or part of the body is de‐
tected while the sunroof is closing au‐ tomatically, it will reverse the direction,
and then stop.
Features of your vehicle
4-34
Page 123 of 523
MIRRORS
Inside rearview mirror
Adjust the rearview mirror to center onthe view through the rear window.
Make this adjustment before you start
driving.
WARNING
nRear visibility
Do not place objects in the rear seator cargo area which would interferewith your vision through the rearwindow.
WARNING
Do not adjust the rearview mirrorwhile the vehicle is moving. Thiscould result in loss of control, and anaccident which could cause death,serious injury or property damage.
WARNING
Do not modify the inside mirror anddo not install a wide mirror. It couldresult in injury, during an accident ordeployment of the air bag.
Day/night rearview mirror (if
equipped)
Make this adjustment before you start
driving and while the day/night lever is in the day position (1). Pull the day/night lever toward you (2)
to reduce the glare from the headlights
of the vehicles behind you during night driving.
Remember that you lose some rear‐
view clarity in the night position.
❈ (1) : Day, (2) : Night
4-41
4
Features of your vehicle
Page 135 of 523
LCD WINDOWS (IF EQUIPPED)
Overview
0 : # #
' P S U Z Q F $
% D M V T U F S
LCD windows show the following vari‐
ous information to drivers.
- Trip information
- LCD modes
- Warning messages
Trip information (Trip computer)
The trip computer is a microcomputer-
controlled driver information system that displays information related to
driving.
NOTICE
Some driving information stored in
the trip computer (for example
Average Vehicle Speed) resets if the
battery is disconnected.
Trip Modes
- For Type A, B clusterLÜ 5 S J Q N F U F S < " >
LÜ & M B Q T F E 5 J N F < " >
LÜ " W F S B H F 7 F I J D M F 4 Q F F E < " >
5 3 * 1 "
LÜ 5 S J Q N F U F S < # >
LÜ & M B Q T F E 5 J N F < # >
LÜ " W F S B H F 7 F I J D M F 4 Q F F E < # >
5 3 * 1 #
LÜ % J T U B O D F 5 P & N Q U Z
LÜ " W F S B H F ' V F M & D P O P N Z
LÜ * O T U B O U ' V F M & D P O P N Z
' 6 & - & $ 0 / 0 . :
LÜ 4 F S W J D F S F N J O E F S
4 F S W J D F
LÜ 4 Q F F E 0 O 0 G G
4 Q F F E
4-53
4
Features of your vehicle
Page 165 of 523
Auto light position (if equipped)
¥ 5 Z Q F "
¥ 5 Z Q F #
When the light switch is in the AUTO
light position, the taillights and head‐ lights will be turned ON or OFF auto‐
matically depending on the amount of
light outside the vehicle.
CAUTION
•Never place anything over sensor(1) located on the instrument pan‐el, this will ensure better auto-light system control.
•Don’t clean the sensor using a win‐dow cleaner, the cleanser mayleave a light film which could inter‐fere with sensor operation.
•If your vehicle has window tint orother types of metallic coating onthe front windshield, the Autolight system may not work prop‐erly.
High beam operation
¥ 5 Z Q F "
¥ 5 Z Q F #
To turn on the high beam headlights,
push the lever away from you. Pull it back for low beams.
4-83
4
Features of your vehicle
Page 170 of 523
High beam Assist (if equipped)
0 : #
The High Beam Assist is a system that
automatically adjusts the headlamp range (switches between high beam
and low beam) according to the bright‐
ness of other vehicles and road condi‐ tions.
Operating condition
1. Place the light switch in the AUTO position.
2. Turn on the high beam by pushing the lever away from you.
The High Beam Assist (
) indicator
will illuminate. 3. The High Beam Assist will turn on
when vehicle speed is above 45 kph(28 mph). • If the lever is pushed away when the High Beam Assist is operat‐
ing, the High Beam Assist will
turn off and the high beam will
be on continuously. The High
Beam Assist (
) indicator will
turn off.
• If the lever is pulled towards you when the high beam is on with
operating High Beam Assist, theHigh Beam Assist will turn off.
4. If the light switch is placed to the headlamp position, the High Beam
Assist will turn off and the low
beam will be on continuously.
The high beam switches to low beam in
the below conditions. - When the High Beam Assist is off.
- When the light switch is not in the AUTO position.
- When the headlamp is detected from the on-coming vehicle.
- When the tail lamp is detected from the front vehicle.
- When the surrounding is bright enough high beams are not needed. - When streetlights or other lights are
detected.
- When vehicle speed is below 35 km/h (22 mph).
- When headlamp/taillamp of bicycle/ motorcycle is detected.CAUTION
The system may not operate nor‐mally in the below conditions.•When the light from the on-com‐ing or front vehicle is not detectedbecause of lamp damage, hiddenfrom sight, etc.
•When the lamp of the on-comingor front vehicle is covered withdust, snow or water.
•When the light from the on-com‐ing or front vehicle is not detectedbecause of exhaust fume, smoke,fog, snow, etc.
•When the front window is coveredwith foreign matters such as ice,dust, fog, or is damaged.
•When there is a similar shape lampwith the front vehicle’s lamps.
(Continued)
Features of your vehicle
4-88
Page 175 of 523
(Continued)
•To prevent damage to the wiperarms and other components, donot attempt to move the wipersmanually.
•To prevent possible damage to thewipers and washer system, useanti-freezing washer fluids in thewinter season or cold weather.
Rear window wiper and washer
switch (if equipped)
The rear window wiper and washer
switch is located at the end of the wip‐ er and washer switch lever. Turn the
switch to desired position to operate
the rear wiper and washer. 6. 2 - Normal wiper operation
7. 1/ON - Intermittent wipe
8. O - Wiper is not in operation
¥ 5 Z Q F "
¥ 5 Z Q F #
4-93
4
Features of your vehicle
Page 180 of 523
DEFROSTER
CAUTION
To prevent damage to the conduc‐tors bonded to the inside surface ofthe rear window, never use sharp in‐struments or window cleaners con‐taining abrasives to clean the win‐dow.
NOTICE
If you want to defrost and defog the
front windshield, refer to L
Page 181 of 523
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
1. Fan speed control knob
2. Mode selection knob
3. Temperature control knob
4. Air conditioning button (if equipped)
5. Rear window defroster button
6. Air intake control button
CAUTION
Operating the blower when the igni‐tion switch is in the ON positioncould cause the battery to discharge.Operate the blower when the engineis running.
4-99
4
Features of your vehicle
