2018 KIA STONIC low beam
[x] Cancel search: low beamPage 349 of 523
Headlamp (Low/High beam) bulb replacement
(Headlamp Type B)............................................................. 8-111
Front turn signal lamp bulb replacement (Head‐
lamp Type B)........................................................................8-112
Static bending light replacement (Headlamp Type B).... 8-112
Position lamp / Day time running lamp (LED
type) replacement (Headlamp Type B)........................... 8-113
Front fog lamp bulb replacement.................................... 8-113
Rear turn signal lamp bulb replacement........................ 8-114
Stop and tail lamp bulb replacement...............................8-115
Tail lamp (inside) bulb replacement................................. 8-116
Stop and tail lamp (LED type) bulb replacement.......... 8-116
Back up lamp bulb replacement....................................... 8-117
Rear fog lamp bulb replacement......................................8-117
High mounted stop lamp bulb replacement................... 8-117
License plate lamp bulb replacement.............................. 8-118
Map lamp bulb replacement............................................. 8-118
Vanity mirror lamp bulb replacement............................. 8-119
Room lamp bulb replacement...........................................8-119
Glove box lamp bulb replacement.................................... 8-120
Tailgate room lamp bulb replacement............................ 8-120
Headlamp and front fog lamp aiming (for Europe)...... 8-121
Appearance care..................................................................... 8-128 Exterior care........................................................................ 8-128
Interior care......................................................................... 8-132
Emission control system ...................................................... 8-134 Crankcase emission control system................................ 8-134
Evaporative emission control system............................. 8-134
Exhaust emission control system....................................8-134
Lean NOx trap .................................................................... 8-136
8
Page 451 of 523
•Lamp part malfunction due to electri‐cal control system stabilization
A normally functioning lamp may
flicker momentarily. This momentary occurrence is due to stabilization unc‐
tion of the vehicle's electrical on con‐
trol system. If the lamp soon returns
to normal, the vehicle does not re‐
quire service.
However, if the lamp goes out after he momentary flickering, or the flick‐
ering continues, have the system
serviced by a professional workshop.
Kia recommends to visit an author‐
ized Kia dealer/service partner.
NOTICE
•If the light bulb or lamp connector
is removed from an operating
lamp activated by electricity, the
fuse box’s electronic device may
scan it as a malfunction. There‐
fore, a lamp malfunction history
may be recorded in Diagnostic
Trouble Code (DTC) in the fuse
box.
(Continued)
(Continued)
•It is normal for an operating lamp
may blink temporarily. Since this
occurrence is due stabilization
function of the vehicle’s electronic
control device, if the lamp lights up
normally after temporary blinking,
there is no problem in the vehicle.
However, if the lamp continues to
blink several times or turn off
completely, there may be an error
in the vehicle’s electronic control
device. In this case, have the vehi‐
cle checked by a professional
workshop immediately. Kia recom‐
mends to visit an authorized Kia
dealer/service partner.
NOTICE
After an accident or after the head‐
light assembly is reinstalled, have
the headlight aiming adjusted by a
professional workshop. Kia recom‐
mends to visit an authorized Kia
dealer/service partner.
NOTICE
After driving in heavy rain or wash‐
ing, headlamp and taillamp lenses
could appear frosty. This condition is
caused by the temperature differ‐
ence between the lamp inside and
outside. This is similar to the con‐
densation on your windows inside
your vehicle during the rain and
doesn’t indicate a problem with your
vehicle. If the water leaks into the
lamp bulb circuitry, have the vehicle
checked by a professional workshop.
Kia recommends to visit an author‐
ized Kia dealer/service partner.
NOTICE
nTraffic Change (For Europe)
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direc‐
tion, this asymmetric part will dazzle
oncoming car driver. To prevent daz‐
(Continued)
8-105
8
Maintenance
Page 455 of 523
Side repeater lamp (bulb type)
bulb Replacement
1. Remove the lamp assembly fromthe vehicle by prying the lens and
pulling the assembly out.
2. Disconnect the bulb electrical con‐ nector.
3. Separate the socket and the lens parts by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
lens part.
4. Remove the bulb by pulling it straight out.
5. Insert a new bulb in the socket. 6. Reassemble the socket and the
lens part.
7. Connect the bulb electrical connec‐ tor.
8. Reinstall the lamp assembly to the body of the vehicle.
Headlamp (Low/High beam) bulb
replacement (Headlamp Type A)
0 : # #
1. Open the hood.
2. Remove the headlamp bulb coverby turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector. 4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
5. Install a new bulb-socket assembly in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb
8-109
8
Maintenance
Page 457 of 523
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐ to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.Headlamp (Low/High beam) bulb
replacement (Headlamp Type B)
0 : # #
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector.
4. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly. 5. Install a new bulb-socket assembly
in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb
8-111
8
Maintenance
Page 467 of 523
Headlamp and front fog lamp
aiming (for Europe)
Headlamp aiming
¥ 5 Z Q F "
¥ 5 Z Q F #
1. Inflate the tires to the specifiedpressure and remove any loads from the vehicle except the driver,
spare tire, and tools.
2. The vehicle should be placed on a flat floor.
3. Draw vertical lines (Vertical lines passing through respective head
lamp centers) and a horizontal line
(Horizontal line passing through center of head lamps) on the
screen.
4. With the head lamp and battery in normal condition, aim the head
lamps so the brightest portion falls
on the horizontal and vertical lines.
5. To aim the low and high beams left or right, turn the driver (1) clock‐
wise or counterclockwise. To aim
the low and high beams up or
down, turn the driver (2) clockwise
or counterclockwise.
Front fog lamp aiming
The front fog lamp can be aimed as the
same manner of the head lamps aim‐ ing.
With the front fog lamps and battery
normal condition, aim the front fog
lamps.
To aim the front fog lamp up or down, turn the driver clockwise or counter‐
clockwise.
8-121
8
Maintenance
Page 469 of 523
Type A
Vehicle condition (Ifequipped 185/65R15tire)
Head lamp (MFR type)Head lamp (BI-FUNCTION type)
Ground HeightDistance betweenlampsGround HeightDistance betweenlamps
Low/High beamLow/High beamLow/High beamLow/High beam
H1W1H1'W1'
Without driver757 (29.8) 1,259 (49.6) 760 (29.9) 1,250 (49.2)
[mm (in)]
With driver 747 (29.4) 1,259 (49.6) 750 (29.5) 1,250 (49.2)
[mm (in)]
Type B
Vehicle condition (Ifequipped 205/55R17tire)
Head lamp (MFR type)Head lamp (BI-FUNCTION type)
Ground HeightDistance betweenlampsGround HeightDistance betweenlamps
Low/High beamLow/High beamLow/High beamLow/High beam
H1W1H1'W1'
Without driver775 (30.5) 1,259 (49.6) 778 (30.6) 1,250 (49.2)
[mm (in)]
With driver 765 (30.1) 1,259 (49.6)) 768 (30.2) 1,250 (49.2)
[mm (in)]
8-123
8
Maintenance
Page 471 of 523
¥ # B T F E P O N T D S F F O
" 7 F I J D M F B Y J T
# 7 F S U J D B M M J O F P G U I F M F G U I F B E M B N Q C V M C D F O U F S
$ 7 F S U J D B M M J O F P G U I F S J H I U I F B E M B N Q C V M C D F O U F S
% ) P S J [ P O U B M M J O F P G I F B E M B N Q C V M C D F O U F S & ( S P V O E
' $ V U 0 G G M J O F
Head lamp low beam (LHD Vehicle)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.
8-125
8
Maintenance
Page 472 of 523
¥ # B T F E P O N T D S F F O
" 7 F I J D M F B Y J T
# 7 F S U J D B M M J O F P G U I F M F G U I F B E M B N Q C V M C D F O U F S
$ 7 F S U J D B M M J O F P G U I F S J H I U I F B E M B N Q C V M C D F O U F S
% ) P S J [ P O U B M M J O F P G I F B E M B N Q C V M C D F O U F S
& ( S P V O E
' $ V U 0 G G M J O F
Head lamp low beam (RHD Vehicle)
1. Turn the low beam on without driver aboard.
2. The cut-off line should be projected in the cut-off line shown in the picture.
3. When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
4. If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.
Maintenance
8-126