2018 KIA STONIC lock

Removal and installation (if equipped)
To remove the headrest, raise it as far
as it can go then press the release but‐ ton (1) while pulling upward (2).
To reinstall the headrest, put the head‐
rest poles (3) into the holes while
pressing the release button (1). Then adjust it to the appropriate height.
WARNING
Make sure the headrest locks in po‐sition after adjusting it to properlyprotect the occupants.
Folding the rear seat (if equipped)
The rear seatbacks may be folded to
facilitate carrying long items or to in‐
crease the luggage capacity of the ve‐ hicle.
WARNING
The purpose of the fold-down rearseatbacks is to allow you to carrylonger objects than could not other‐wise be accommodated.Never allow passengers to sit on topof the folded down seatback whilethe car is moving as this is not aproper seating position and no seatbelts are available for use. This couldresult in serious injury or death incase of an accident or sudden stop.Objects carried on the folded downseatback should not extend higherthan the top of the front seats. Thiscould allow cargo to slide forwardand cause injury or damage duringsudden stops.
The rear seatbacks may be folded for‐
ward to provide additional cargo space and to provide access to the cargo area. • To raise the seatback, lift and push it firmly until it clicks into place. • When you return the seatback to its
upright position, reposition the rear
safety belts so that they can be used
by rear seat passengers.
WARNING
Do not fold the rear seat, if the driv‐er's position is not properly set ac‐cording to the driver's physical figureafter folding the rear seat. A suddenstop or collision may cause injury.
CAUTION
•When folding or unfolding the rearseat, make sure to move the frontseat fully forward. If there are notenough space to fold the rear seat,never fold it by force. It will causedamage to the headrest or the re‐lated parts of the seat.
•Before using the seat belt, be sureto remove it from the holder. Ifyou pull out the seat belt while it'sin the holder, it may damage theseat belt or holder.
(Continued)
Safety features of your vehicle
3-10

(Continued)
•Use the holder only when there isno passengers in the rear seat orwhen you need to fold the rearseat.
To fold down the rear seatback:1. When folding the seat back, insert the rear seat belt buckle in the
pocket between the rear seatback
and cushion then make sure both
seatbelts do not interfere with
stowed luggage and cargo. Then,
insert the seat belt into the two
holes located on both sides. 2. Set the front seatback to the up‐
right position and if necessary, slide the front seat forward.
3. Lower the rear headrests to lowest position.
4. Pull the lock release lever and foldthe rear seatback forward and
down firmly.
To unfold the rear seat
1. To use the rear seat, lift and pull the seatback backward. Pull the
seatback firmly until it clicks into
place. Make sure the seatback is
locked in place. When you return
the seatback to its upright position, always be sure it has locked into
position by pushing on the top of
the seatback.
If you can not see the red line at
the bottom of folding lever, it
means the seatback is locked com‐
pletely.
2. Return the rear seat belt to the proper position.
3. When the seatback is completely installed, check the seatback fold‐
ing lever again.
WARNING
nUprighting seat
When you return the seatback to itsupright position, hold the seatbackand return it slowly. If the seatbackis returned without holding it, theback of the seat could spring for‐
(Continued)

3-11
3
Safety features of your vehicle

(Continued)
ward resulting in injury caused bybeing struck by the seatback.
WARNING
After folding the rear seat, unlessthe driver’s position is properly setaccording to the driver’s physical fig‐ure, do not fold the rear seat. It mayincrease body injuries in a suddenstop or collision.
WARNING
When you return the rear seatbackto its upright position after beingfolded down:Be careful not to damage the seatbelt webbing or buckle. Do not allowthe seat belt webbing or buckle toget caught or pinched in the rearseat. Ensure that the seatback iscompletely locked into its uprightposition by pushing on the top of theseatback. Otherwise, in an accidentor sudden stop, the seat could fold
(Continued)
(Continued)
down and allow cargo enter the pas‐senger compartment, which couldresult in serious injury or death.
CAUTION
nDamaging rear seat belt buck‐les
When you fold the rear seatback, in‐sert the buckle between the rearseatback and cushion. Doing so canprevent the buckle from being dam‐aged by the rear seatback.
CAUTION
nRear seat belts
When returning the rear seatbacksto the upright position, remember toreturn the rear shoulder belts totheir proper position.
WARNING
nCargo
Cargo should always be secured toprevent it from being thrown aboutthe vehicle in a collision and causinginjury to the vehicle occupants. Donot place objects in the rear seats,since they cannot be properly se‐cured and may hit the front seat oc‐cupants in a collision.
WARNING
nCargo loading
Make sure the engine is off, the au‐tomatic transaxle is in P (Park) orthe manual transaxle is in 1st, andthe parking brake is securely appliedwhenever loading or unloading cargo.Failure to take these steps may al‐low the vehicle to move if the shiftlever is inadvertently moved to an‐other position.
Safety features of your vehicle
3-12

Lap/shoulder belt
Height adjustment (front seat, if equip‐ped)
'SPOU
TFBU
You can adjust the height of the shoul‐
der belt anchor to one of the 3 posi‐ tions for maximum comfort and safety.
The height of the adjusting seat belt
should not be too close to your neck.
The shoulder portion should be adjus‐ ted so that it lies across your chest and
midway over your shoulder near the
door and not your neck.
To adjust the height of the seat belt anchor, lower or raise the height ad‐
juster into an appropriate position. To raise the height adjuster, pull it up
(1). To lower it, push it down (3) while pressing the height adjuster button (2).
Release the button to lock the anchor
into position. Try sliding the height ad‐
juster to make sure that it has locked into position.
WARNING
•Verify the shoulder belt anchor islocked into position at the appro‐priate height. Never position theshoulder belt across your neck orface. Improperly positioned seatbelts can cause serious injuries inan accident.
•Failure to replace seat belts afteran accident could leave you withdamaged seat belts that will notprovide protection in the event ofanother collision leading to person‐al injury or death. Replace yourseat belts after being in an acci‐dent as soon as possible.
To fasten your seat belt:
To fasten your seat belt, pull it out of
the retractor and insert the metal tab (1) into the buckle (2). There will be an
audible "click" when the tab locks into
the buckle.
The seat belt automatically adjusts to the proper length only after the lap
belt portion is adjusted manually so
that it fits snugly around your hips. If you lean forward in a slow, easy mo‐
tion, the belt will extend and let you
move around. If there is a sudden stop or impact, however, the belt will lock in‐
to position. It will also lock if you try to
lean forward too quickly.
Safety features of your vehicle
3-16

NOTICE
If you are not able to pull out the
seat belt from the retractor, firmly
pull the belt out and release it. Then
you will be able to pull the belt out
smoothly.
WARNING
You should place the lap belt portionas low as possible and snugly acrossyour hips, not on your waist. If thelap belt is located too high on your
(Continued)
(Continued)
waist, it may increase the chance ofinjury in the event of a collision. Botharms should not be under or overthe belt. Rather, one should be overand the other under, as shown in theillustration.Never wear the seat belt under thearm nearest the door.
0:##
The seat belt should be locked into the
buckle on each seat cushion to be prop‐ erly fastened. ❈ A : Rear right seat belt fastening
buckle
B : Rear center seat belt fastening
buckle C : Rear left seat belt fastening
buckle
0:##
When using the rear center seat belt,
the buckle with the L

Lap belt (if equipped)
To fasten your seat belt:
To fasten a 2-point static type belt, in‐
sert the metal tab (1) into the locking buckle (2). There will be an audible
"click" when the tab locks into the buck‐
le. Check to make sure the belt is prop‐ erly locked and that the belt is not
twisted.
With a 2-point static type seat belt, the
length must be adjusted manually so it
fits snugly around your body. Fasten the belt and pull on the loose end to
tighten. The belt should be placed as low as
possible on your hips (1), not on your waist. If the belt is too high, it could in‐
crease the possibility of your being in‐
jured in an accident.
When using the rear center seat belt, the buckle with the L

WARNING
The center lap belt latching mecha‐nism is different from those for therear seat shoulder belts. When fas‐tening the rear seat shoulder beltsor the center lap belt, make surethey are inserted into the correctbuckles to obtain maximum protec‐tion from the seat belt system andassure proper operation.
Stowing the rear seat belt
The rear seat belt buckles can be stow‐
ed in the pocket between the rear
seatback and cushion when not in use.
Pre-tensioner seat belt (if
equipped)
Your vehicle is equipped with pre-ten‐
sioner seatbelts at the front and rear outboard seating positions. The pur‐
pose of the pre-tensioner is to make
sure that the seat belts fit tightly against the occupant's body in certain
collisions. The pre-tensioner seat belts
may be activated in crashes where the collision is severe enough. When the vehicle stops suddenly, or if
the occupant tries to lean forward too
quickly, the seat belt retractor will lock into position. In certain frontal colli‐
sions, the pre-tensioner will activate
and pull the seat belt into tighter con‐ tact against the occupant's body.
If the system senses excessive tension
on the driver or passenger's seat belt
when the pre-tensioner activates, the load limiter inside the pre-tensioner will
release some of the pressure on the af‐fected seat belt. (if equipped)
WARNING
For your safety, be sure that thebelt webbing is not loose or twistedand always sit properly on your seat.
NOTICE
nif equipped with rollover sen‐
sor
The pre-tensioner will activate not
only in a frontal collision but also in a
side collision or rollover, if the vehicle
(Continued)
Safety features of your vehicle
3-20

Front passenger's air bag warning
label for child restraint system
¥
5ZQF
"
¥
5ZQF
#
Never place a rear-facing child restraint
in the front passenger’s seat. If the air bag deploys, it would impact the rear-
facing child restraint, causing serious or
fatal injury.
In addition, do not place a front-facing child restraints in the front passenger’s
seat. If the front passenger air bag in‐
flates, it could cause serious or fatal in‐ juries to the child.
If your vehicle is equipped with the pas‐
senger’s front air bag ON/OFF switch,
you can activate or deactivate the front passenger’s air bag when neces‐
sary.
WARNING
•Extreme Hazard! Do not use arearward facing child restraint ona seat protected by an air bag infront of it!
•NEVER use a rearward facing childrestraint on a seat protected by anACTIVE AIRBAG in front of it,DEATH or SERIOUS INJURY to theCHILD can occur.
(Continued)
(Continued)
•Never put a child restraint in thefront passenger’s seat. If the frontpassenger air bag inflates, it cancause serious or fatal injuries.
•When children are seated in therear outboard seats of a vehicleequipped with side and/or curtainair bags, be sure to install the childrestraint system as far away fromthe door side as possible, and se‐curely lock the child restraint sys‐tem in position.Inflation of side and/or curtain airbags could cause serious injury ordeath to an infant or child.

3-41
3
Safety features of your vehicle