2018 KIA STONIC lock

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Static bending light replacement
(Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
Maintenance
8-112

3. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
4. Remove the bulb from bulb-socket by pulling it out.
5. Insert a new bulb by inserting it in‐ to the bulb-socket.
6. Install the bulb-socket in the head‐ lamp assembly by aligning the tabs
on the bulb-socket with the slots in
the headlamp assembly. Push the
bulb-socket into the headlamp as‐
sembly and turn the bulb-socket
clockwise.
7. Install the headlamp bulb cover by turning it clockwise.Position lamp / Day time
running lamp (LED type)
replacement (Headlamp Type B)
0:##
If the position lamp + DRL (LED) (1)
does not operate, have your vehicle checked by a professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
The LED lamps cannot be replaced as a
single unit because it is an integrated unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or re‐
pair the position lamp + DRL (LED), for it may damage related parts of the ve‐
hicle.
Front fog lamp bulb
replacement
0:##
If the front fog lamp (1) does not oper‐
ate, have your vehicle checked by a professional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.

8-113
8
Maintenance

Rear turn signal lamp bulb
replacement
0:##
1. Open the tail gate.
2. Loosen the light assembly retainingscrews with a cross-tip screwdriv‐
er.
0:##
3. Remove the rear combination lamp assembly from the body of the ve‐
hicle.
4. Disconnect the rear combination lamp connector.
0:##
5. Remove the socket from the as‐sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it in‐ to the socket and rotating it until it
locks into place.
8. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp assembly to the body of the vehi‐
cle.
Maintenance
8-114

Stop and tail lamp bulb
replacement
0:##
1. Open the tail gate.
2. Loosen the light assembly retainingscrews with a cross-tip screwdriv‐
er.
0:##
3. Remove the rear combination lamp assembly from the body of the ve‐
hicle.
4. Disconnect the rear combination lamp connector.
0:##
5. Remove the socket from the as‐sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
6. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it in‐ to the socket and rotating it until it
locks into place.
8. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp assembly to the body of the vehi‐
cle.

8-115
8
Maintenance

Tail lamp (inside) bulb
replacement
0:##
1. Open the tailgate.
2. Remove the service cover.
0:##
3. Remove the socket from the as‐sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
4. Remove the bulb from bulb-socket by pulling it out.
5. Insert a new bulb by inserting it in‐ to the bulb-socket.
6. Install the socket in the assembly by aligning the tabs on the socketwith the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
7. Install the service cover by putting it into the service hole.Stop and tail lamp (LED type)
bulb replacement
0:##
If the stop and tail lamp (LED) (1,2,3,4)
does not operate, have your vehicle checked by a professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
The LED lamps cannot be replaced as a
single unit because it is an integrated unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or re‐
pair the stop and tail lamp (LED), for it may damage related parts of the vehi‐
cle.
Maintenance
8-116

License plate lamp bulb
replacement
0:##
1. Using a flat-blade screwdriver, gen‐tly pry the lens cover from lamp
housing.
2. Remove the socket from the as‐ sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
3. Remove the bulb from bulb-socket by pulling it out.
4. Insert a new bulb by inserting it in‐ to the bulb-socket. 5. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
6. Align the lens cover tabs with the lamp housing notches and snap the
lens into place.
Map lamp bulb replacement
WARNING
Prior to working on the Interiorlamps, ensure that the L

Headlamp and front fog lamp
aiming (for Europe)
Headlamp aiming
¥
5ZQF
"
¥
5ZQF
#
1. Inflate the tires to the specifiedpressure and remove any loads from the vehicle except the driver,
spare tire, and tools.
2. The vehicle should be placed on a flat floor.
3. Draw vertical lines (Vertical lines passing through respective head
lamp centers) and a horizontal line
(Horizontal line passing through center of head lamps) on the
screen.
4. With the head lamp and battery in normal condition, aim the head
lamps so the brightest portion falls
on the horizontal and vertical lines.
5. To aim the low and high beams left or right, turn the driver (1) clock‐
wise or counterclockwise. To aim
the low and high beams up or
down, turn the driver (2) clockwise
or counterclockwise.
Front fog lamp aiming
The front fog lamp can be aimed as the
same manner of the head lamps aim‐ ing.
With the front fog lamps and battery
normal condition, aim the front fog
lamps.
To aim the front fog lamp up or down, turn the driver clockwise or counter‐
clockwise.

8-121
8
Maintenance

ENGINE NUMBER
¥
(BTPMJOF
FOHJOF
-

¥
(BTPMJOF
FOHJOF
-

¥
(BTPMJOF
FOHJOF
-

06#-#
%JFTFM
FOHJOF
--

The engine number is stamped on the
engine block as shown in the drawing.
Specifications & Consumer information
9-20