2018 KIA STONIC lock

SymbolFuse ratingCircuit Protected
10A Back-Up Lamp Switch
40A Instrument Panel Junction Block
50A Instrument Panel Junction Block (Power Window Relay)
40A Ignition Switch, PDM Relay Box (IG2 Relay)
40A Cooling Fan1 Relay, Cooling Fan2 Relay
30A Main Relay
10A Air Conditioner Clutch Type ECV Relay
20A Head Lamp Relay
20A Head Lamp High Relay
FUEL
PUMP20A Fuel Pump Relay
15A Horn Relay, Burglar Alarm Horn Relay
E315A ECM/PCM
AMS10A Battery Sensor
40A Instrument Panel Junction Block (Tail Lamp Relay)
40A Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
POWER
OUTLET40A Instrument Panel Junction Block (Power Outlet Relay)

8-95
8
Maintenance

SymbolFuse ratingCircuit Protected
INJECTOR15AFuel Pump Relay, ECM/PCM, Injector #1~#4, Oil Control Valve #1, #2 (A/T), Purge Control Sole‐
noid Valve (A/T)
10A Back-Up Lamp Switch
40A Instrument Panel Junction Block
50A Instrument Panel Junction Block (Power Window Relay)
40A Ignition Switch, PDM Relay Box (IG2 Relay)
40A Cooling Fan1 Relay, Cooling Fan2 Relay
30A Main Relay
10A Air Conditioner Clutch Type ECV Relay
20A PCM (A/T)
20A Head Lamp Relay
20A Head Lamp High Relay
FUEL
PUMP20A Fuel Pump Relay
15A Horn Relay, Burglar Alarm Horn Relay
E315A ECM/PCM
AMS10A Battery Sensor
40A Instrument Panel Junction Block (Tail Lamp Relay)
Maintenance
8-98

SymbolFuse ratingCircuit Protected
40A Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
POWER
OUTLET40A Instrument Panel Junction Block (Power Outlet Relay)
Relay(Kappa 1.4L MPI Engine (Gaso‐
line))
SymbolRelay NameType
Start Relay MICRO
A/C Blower Relay MICRO
FUEL
PUMPFuel Pump Relay MICRO
Cooling Fan1 Relay MICRO
Wiper HI RelayMICRO
LOWiper LO Relay MICRO
Head Lamp High Relay MICRO
Head Lamp RelayMICRO
2Cooling Fan2 Relay MICRO
Horn RelayMICRO
Burglar Alarm Horn Relay MICRO
MAINMain RelayMINI

8-99
8
Maintenance

SymbolFuse ratingCircuit Protected
E420A ECM
S315AEGR Cooling Bypass Solenoid, Fuel Pressure Regulating Valve, Stop Lamp Switch, Fuel Pump Relay, A/C Blower Relay, Fuel Heat Relay
10A Back-Up Lamp Switch
40A Instrument Panel Junction Block
50A Instrument Panel Junction Block (Power Window Relay)
40A Ignition Switch, PDM Relay Box (IG2 Relay)
50A Cooling Fan1 Relay, Cooling Fan2 Relay
40A Fuel Heat Relay
30A Main Relay
10A Air Conditioner Clutch Type ECV Relay
20A Not Used
20A Head Lamp Relay
20A Head Lamp High Relay
FUEL
PUMP20A Fuel Pump Relay
15A Horn Relay, Burglar Alarm Horn Relay
E315A ECM/PCM

8-101
8
Maintenance

SymbolFuse ratingCircuit Protected
AMS10A Battery Sensor
40A Instrument Panel Junction Block (Tail Lamp Relay)
40A Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
POWER
OUTLET40A Instrument Panel Junction Block (Power Outlet Relay)
Relay(U-II 1.4L/1.6L Engine (Diesel))
SymbolRelay NameType
Start Relay MICRO
A/C Blower Relay MICRO
FUEL
PUMPFuel Pump Relay MICRO
Cooling Fan1 Relay MICRO
Wiper HI RelayMICRO
LOWiper LO Relay MICRO
Head Lamp High Relay MICRO
Head Lamp RelayMICRO
2Cooling Fan2 Relay MICRO
Horn RelayMICRO
Maintenance
8-102

Side repeater lamp (bulb type)
bulb Replacement
1. Remove the lamp assembly fromthe vehicle by prying the lens and
pulling the assembly out.
2. Disconnect the bulb electrical con‐ nector.
3. Separate the socket and the lens parts by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
lens part.
4. Remove the bulb by pulling it straight out.
5. Insert a new bulb in the socket. 6. Reassemble the socket and the
lens part.
7. Connect the bulb electrical connec‐ tor.
8. Reinstall the lamp assembly to the body of the vehicle.
Headlamp (Low/High beam) bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the headlamp bulb coverby turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector. 4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
5. Install a new bulb-socket assembly in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb

8-109
8
Maintenance

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Position lamp / Day time
running lamp bulb replacement
(Headlamp Type A)
0:##
1. Open the hood.
Maintenance
8-110

2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐ to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.Headlamp (Low/High beam) bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
3. Disconnect the headlamp bulb socket-connector.
4. Remove the bulb-socket from the headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly. 5. Install a new bulb-socket assembly
in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by turning it clockwise.
Headlamp bulb

8-111
8
Maintenance