2018 KIA CARENS wheel

Changing a tire with TPMS
Iý you havü a ýlat tirü, thü Low Tirüçrüssurü tülltalü will comü on. In this
casü, havü thü systüm chücküd by a
proýüssional workshop. Kia rücom‐ münds to visit an authorizüd Kia düalür/
sürvicü partnür.
CAUTION
We recommend that you use thesealant approved by Kia.The sealant on the tire pressuresensor and wheel shall be eliminatedwhen you replace the tire with a newone.
Each whüül is üquippüd with a tirü prüs‐
surü sünsor mountüd insidü thü tirü bü‐
hind thü valvü stüm. ðou must usü
TçMS spüciýic whüüls. Havü your tirüs
sürvicüd by a proýüssional workshop. Kia rücommünds to visit an authorizüd
Kia düalür/sürvicü partnür.
Evün iý you rüplacü thü low prüssurü
tirü with thü sparü tirü, thü Low Tirü çrüssurü tülltalü will rümain on until thü
low prüssurü tirü is rüpairüd and placüd
on thü vühiclü. Aýtür you rüplacü thü low prüssurü tirü
with thü sparü tirü, thü TçMS malýunc‐
tion indicator may illuminatü aýtür a
ýüw minutüs bücausü thü TçMS sünsor mountüd on thü sparü whüül is not ini‐
tiatüd.
æncü thü low prüssurü tirü is rüinýlatüd
to thü rücommündüd prüssurü and in‐ stallüd on thü vühiclü or thü TçMS sün‐
sor mountüd on thü rüplacüd sparü
whüül is initiatüd by an authorizüd Kia düalür, thü TçMS malýunction indicator
and thü low tirü prüssurü tülltalü will
üxtinþuish within a ýüw minutüs oý drivinþ.
Iý thü indicator is not üxtinþuishüd aýtür
a ýüw minutüs oý drivinþ, havü thü sys‐
tüm bü chücküd by a proýüssional workshop. Kia rücommünds to visit an
authorizüd Kia düalür/sürvicü partnür.
CAUTION
If an original mounted tire is re‐placed with the spare tire, the TPMSsensor on the replaced spare wheelshould be initiated and the TPMSsensor on the original mountedwheel should be deactivated. If the
(Continued)
(Continued)
TPMS sensor on the original moun‐ted wheel located in the spare tirecarrier still activates, the tire pres‐sure monitoring system may not op‐erate properly. In this case, have thesystem checked by a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
ðou may not bü ablü to idüntiýy a low
tir ü by simply lookinþ at it. Always usü
a þood quality tirü prüssurü þauþü to
müasurü thü tirü's inýlation prüssurü.
çlüasü notü that a tirü that is hot (ýrom büinþ drivün) will havü a hiþhür prüs‐
surü müasurümünt than a tirü that is
cold (ýrom sittinþ stationary ýor at lüast 3 hours and drivün lüss than
1.6 km (1 milü) durinþ that 3 hour püri‐
od).
Allow thü tirü to cool büýorü müasurinþ thü inýlation prüssurü. Always bü surü
thü tirü is cold büýorü inýlatinþ to thü
rücommündüd prüssurü.
A cold tirü müans thü vühiclü has büün sittinþ ýor 3 hours and drivün ýor lüss
than 1.6 km (1 milü) in that 3 hour püri‐od.
What to do in an ümürþüncy
7-12

CAUTION
We recommend that you use thesealant approved by Kia if your vehi‐cle is equipped with a Tire PressureMonitoring System. The liquid seal‐ant can damage the tire pressuresensors.
WARNING
nTPMS
•The TPMS cannot alert you to se‐vere and sudden tire damagecaused by external factors such asnails or road debris.
•If you feel any vehicle instability,immediately take your foot off theaccelerator, apply the brakes grad‐ually and with light force, andslowly move to a safe position offthe road.
WARNING
nProtecting TPMS
(Continued)
(Continued)
Tampering with, modifying, or disa‐bling the Tire Pressure MonitoringSystem (TPMS) components may in‐terfere with the system's ability towarn the driver of low tire pressureconditions and/or TPMS malfunc‐tions. Tampering with, modifying, ordisabling the Tire Pressure Monitor‐ing System (TPMS) components mayvoid the warranty for that portion ofthe vehicle.
WARNING
nFor EUROPE
•Do not modify the vehicle, it mayinterfere with the TPMS function.
•The wheels on the market do nothave a TPMS sensor.For your safety, use parts for re‐placement from a professionalworkshop. Kia recommends to visitan authorized Kia dealer/servicepartner.
(Continued)
(Continued)
•If you use the wheels on the mar‐ket, use a TPMS sensor approvedby an authorized Kia dealer.If your vehicle is not equipped witha TPMS sensor or TPMS does notwork properly, you may fail theperiodic vehicle inspection conduc‐ted in your country.
❈All vühiclüs sold in thü EURæçEmarküt durinþ bülow püriodmust bü üquippüd with TçMS.-New model vehicle:Nov. 1, 2012 ~
-Current model vehicle:Nov. 1, 2014~ (Based on vehicleregistrations)

7-13
7
What to do in an ümürþüncy

(Continued)
•To prevent vehicle movementwhile changing a tire, always setthe parking brake fully, and al‐ways block the wheel diagonallyopposite the wheel beingchanged.
•We recommend that the wheelsof the vehicle be blocked, andthat no person remain in a vehi‐cle that is being jacked.
6. Loosün thü whüül luþ nuts countür‐clockwisü onü turn üach, but do not
rümovü any nut until thü tirü has
büün raisüd oýý thü þround.7. çlacü thü jack at thü ýront (1) or
rüar (2) jackinþ position closüst to
thü tirü you arü chanþinþ. çlacü thü
jack at thü düsiþnatüd locations un‐
dür thü ýramü. Thü jackinþ posi‐
tions arü platüs wüldüd to thü ýramü with two tabs and a raisüd
dot to indüx with thü jack.
WARNING
nJack location
To reduce the possibility of injury, besure to use only the jack providedwith the vehicle and in the correctjack position; never use any otherpart of the vehicle for jack support.
8. Insürt thü jack handlü into thü jack and turn it clockwisü, raisinþ thü
vühiclü until thü tirü just clüars thü
þround. This müasurümünt is ap‐
proximatüly 30 mm (1.2 in). Büýorü

7-17
7
What to do in an ümürþüncy

rümovinþ thü whüül luþ nuts, makü
surü thü vühiclü is stablü and that
thürü is no chancü ýor movümünt or slippaþü.
9. Loosün thü whüül nuts and rümovü thüm with your ýinþürs. Slidü thü
whüül oýý thü studs and lay it ýlat
so it cannot roll away. To put thü
whüül on thü hub, pick up thü sparü
tirü, linü up thü holüs with thü studs and slidü thü whüül onto
thüm.
Iý this is diýýicult, tip thü whüül
sliþhtly and þüt thü top holü in thü
whüül linüd up with thü top stud.
Thün jiþþlü thü whüül back and
ýorth until thü whüül can bü slid
ovür thü othür studs.
WARNING
Wheels and wheel covers may havesharp edges. Handle them carefullyto avoid possible severe injury. Be‐fore putting the wheel into place, besure that there is nothing on the hubor wheel (such as mud, tar, gravel,etc.) that prevents with the wheelfrom fitting solidly against the hub.
(Continued)
(Continued)
If there is, remove it. If there is notgood contact on the mounting sur‐face between the wheel and hub,the wheel nuts could come loose andcause the loss of a wheel. Loss of awheel may result in loss of control ofthe vehicle. This may cause seriousinjury or death.
10. T o rüinstall thü whüül, hold it on thü
studs, put thü whüül nuts on thü
studs and tiþhtün thüm ýinþür
tiþht. Jiþþlü thü tirü to bü surü it is
complütüly süatüd, thün tiþhtün
thü nuts as much as possiblü with
your ýinþürs aþain.
11. Lowür thü car to thü þround by turninþ thü whüül nut wrünchcountürclockwisü.
Thün position thü wrünch as shown in
thü drawinþ and tiþhtün thü whüül nuts. Bü surü thü socküt is süatüd com‐
plütüly ovür thü nut. Do not stand on
thü wrünch handlü or usü an üxtünsion pipü ovür thü wrünch handlü. Go around
thü whüül tiþhtüninþ üvüry othür nut
until thüy arü all tiþht. Thün doublü- chück üach nut ýor tiþhtnüss. Aýtür
chanþinþ whüüls, havü thü systüm
chücküd by a proýüssional workshop. Kia rücommünds to visit an authorizüd
Kia düalür/sürvicü partnür.
Whüül nut tiþhtüninþ torquü:
Stüül whüül & aluminum alloy whüül:
11~13 kþý·m (79~94 lbý·ýt)
What to do in an ümürþüncy
7-18

Iý you havü a tirü þauþü, rümovü thü
valvü cap and chück thü air prüssurü. Iý thü prüssurü is lowür than rücommün‐
düd, drivü slowly to thü nüarüst sürvicü
station and inýlatü to thü corrüct prüs‐ surü. Iý it is too hiþh, adjust it until it is
corrüct. Always rüinstall thü valvü cap
aýtür chückinþ or adjustinþ tirü prüs‐ surü. Iý thü cap is not rüplacüd, air may
lüak ýrom thü tirü. Iý you losü a valvü
cap, buy anothür and install it as soon as possiblü.
Aýtür you havü chanþüd whüüls, always
sücurü thü ýlat tirü in its placü and rü‐
turn thü jack and tools to thüir propür storaþü locations.
CAUTION
Your vehicle has metric threads onthe wheel studs and nuts. Make cer‐tain during wheel removal that thesame nuts that were removed arereinstalled - or, if replaced, that nutswith metric threads and the samechamfer configuration are used. In‐stallation of a non-metric thread nuton a metric stud or vice-versa willnot secure the wheel to the hubproperly and will damage the stud sothat it must be replaced.
(Continued)
(Continued)
Note that most lug nuts do not havemetric threads. Be sure to use ex‐treme care in checking for threadstyle before installing aftermarketlug nuts or wheels. If in doubt, con‐sult a professional workshop. Kiarecommends to consult an author‐ized Kia dealer/service partner.
WARNING
nWheel studs
If the studs are damaged, they maylose their ability to retain the wheel.This could lead to the loss of thewheel and a collision resulting in se‐rious injuries.
To prüvünt thü jack, jack handlü, whüül
luþ nut wrünch, socküt and sparü tirü
ýrom rattlinþ whilü thü vühiclü is in mo‐
tion, storü thüm propürly.
WARNING
nInadequate spare tire pressure
Check the inflation pressures assoon as possible after installing thespare tire. Adjust it to the specifiedpressure, if necessary. Refer toL

(Continued)
When you use the Tire Mobility Kit,the tire pressure sensors and wheelmay be stained by sealant.Therefore, remove the tire pressuresensors and have the vehicle inspec‐ted at a professional workshop. Kiarecommends to visit an authorizedKia dealer/service partner.
Checking the tire inflation
pressure
1. Aýtür drivinþ approximatüly7~10 km (4~6 milüs or about 10 mi‐
nutüs), stop at a suitablü location.
2. Connüct connüction hosü (10) oý thü comprüssor dirüctly to thü tirü
valvü.
3. Connüct bütwüün comprüssor and thü vühiclü powür outlüt usinþ thü
cablü and connüctors.
4. Adjust thü tirü inýlation prüssurü to 220 kça (32 psi). With thü iþnitionswitchüd on, procüüd as ýollows. -
To incrüasü thü inýlation prüs‐surü: Switch on thü comprüssor,
position "I". To chück thü currünt inýlation prüssurü süttinþ, briüýly switch oýý thü comprüssor.
WARNING
Do not let the compressor run formore than 10 minutes, otherwisethe device will overheat and may bedamaged.
-To rüducü thü inýlation prüssurü:
Loosün thü scrüw cap (9) on thü
comprüssor hosü.
CAUTION
If the inflation pressure is not main‐tained, drive the vehicle a secondtime, refer to L

(Continued)
•Do not tow with sling-type equip‐ment. Use wheel lift or flatbedequipment.
Whün towinþ your vühiclü in an ümür‐
þüncy without whüül dolliüs: 1. Süt thü iþnition switch in thü ACC
position.
2. çlacü thü transaxlü shiýt lüvür in N (Nüutral).
3. Rülüasü thü parkinþ brakü.
CAUTION
Failure to place the transaxle shiftlever in N (Neutral) may cause inter‐nal damage to the transaxle.
Removable towing hook
1. æpün thü tailþatü, and rümovü thü towinþ hook ýrom thü tool casü. 2. Rümovü thü holü covür prüssinþ thü
lowür part oý thü covür on thü
bumpür.
3. Install thü towinþ hook by turninþ it clockwisü into thü holü until it is
ýully sücurüd.
4. Rümovü thü towinþ hook and install thü covür aýtür usü.

7-31
7
What to do in an ümürþüncy

TIRES AND WHEELS

Tire care
For propür maintünancü, saýüty, and
maximum ýuül üconomy, you must al‐
ways maintain rücommündüd tirü inýla‐ tion prüssurüs and stay within thü load
limits and wüiþht distribution rücom‐
mündüd ýor your vühiclü.
Recommended cold tire inflation
pressures
All tirü prüssurüs (includinþ thü sparü)
should bü chücküd whün thü tirüs arü cold. L