2018 JEEP RENEGADE warning lights

THE KEYS
KEY WITH REMOTE CONTROL
1)1)1)
The metal insert A fig. 4 of the key
operates:
the ignition switch;the door lock.
Press button B to open/close the metal
insert.
ELECTRONIC KEY(versions with "Keyless Enter-N-Go"
system)
On versions equipped with "Keyless
Enter-N-Go" system, the vehicle featuresan electronic keyfig. 5, of which two
copies are provided.
Briefly press button
: unlocking of
doors and luggage compartment, timed
switching-on of internal lights and double
flashing of direction indicators (where
provided).
Briefly press button
: lock of doors and
luggage compartment with roof lights off
and single flash of direction indicators
(where provided).
Press button
: remote opening of
the luggage compartment (to open the
luggage compartment press the button
twice in quick succession).
Press button
: remote switching onof the main beam headlights, for a
maximum of 90 seconds.
Pressing button
again or at the end
of the 90 seconds, the lights switched on
previously will go off (if the parking light
function was already active it will remain
so). If, when 90 seconds have passed,
button
is pressed, the main beam
headlights and the side lights will stay on
for further 30 seconds.
REQUEST FOR ADDITIONAL
KEYS
Should a new key with remote control or
a new electronic key be necessary, go to
a Jeep Dealership, taking an ID
document and the vehicle ownership
documents.
WARNING
1)Press button B only with the key away
from your body, especially your eyes and
from objects which could get damaged
(e.g. your clothes). Do not leave the key
unattended to avoid the button being
accidentally pressed while it is being
handled, e.g. by a child.4J0A0181C
5J0A0315C
16
GETTING TO KNOW YOUR CAR

5)Never extract the mechanical key while
the vehicle is moving. The steering wheel
will automatically lock as soon as it is
turned. This holds true for cars being
towed as well.
6)Before leaving the vehicle, ALWAYS
engage the handbrake. On versions
equipped with automatic transmission,
move the gear lever to STOP (Park) and
press the ignition device to set it to STOP.
When leaving the vehicle, always lock all
the doors by pressing the button on the
handle.
7)For versions equipped with the Keyless
Enter-N-Go system, do not leave the
electronic key inside or near the car or in
a place accessible to children. Do not
leave the vehicle with the ignition device
in MAR position. A child could activate
the electric window winders, other
controls or even start the vehicle.SENTRY KEY®
TheSentry Key®system, prevents
unauthorised use of the vehicle,
disabling engine starting.
The system does not need to be
enabled/activated: operation is
automatic, regardless of the fact that the
vehicle's doors are locked or unlocked.
When the ignition device is taken to
MAR, theSentry Key®system identifies
the code transmitted by the key. If the
code is recognised as valid, theSentry
Key®system enables engine starting.
When the ignition device is brought back
to STOP, theSentry Key®system
deactivates the control unit controlling
the engine, thus preventing its starting.
For the correct engine starting
procedures, see the instructions in the
"Starting the engine" paragraph, "Starting
and driving" chapter.
IRREGULAR OPERATION
If, during starting, the key code is not
correctly recognised, the
icon is
displayed on the instrument panel (see
the instructions in the "Warning lights
and messages" paragraph, "Knowing the
instrument panel" chapter). This
condition leads to the engine switching
off after 2 seconds. In this case, bringthe ignition device to STOP and then to
MAR; if it is still blocked, try with the
other keys provided. If it is still not
possible to start the engine, contact a
Jeep Dealership.
If the
icon is displayed while driving,
this means that the system is running a
self-diagnosis (e.g. due to a voltage
drop). If the displaying is still on, contact
a Jeep Dealership.
19

WARNING
18)As the driver's door mirror is curved, it
may slightly alter the perception of
distance.
EXTERIOR LIGHTS
LIGHT SWITCH
Light switch A fig. 31, located on the left
side of the instrument panel (left hand
drive versions) or on the right side (right
hand drive versions), controls the
headlamp operations, parking lights,
daytime lights, low beams, fog lights,
rear fog lights, and regulates the
instrument panel lighting and the
symbols on the control buttons.
Outside lighting can happen only when
the starter is in position MAR.
The instrument panel and the variouscontrols on the dashboard will be lit up
when the exterior lights are switched on.
AUTO FUNCTION(Dusk sensor)
(where provided)
This is an infrared LED sensor that works
in conjunction with the rain sensor and is
located on the windscreen. It is able to
detect variations in outside lighting
based on the light sensitivity and adjusts
the display Menu or theUconnect™
system.
The higher the sensitivity, the lower the
amount of external light needed to switch
the lights on.
Function activation: turn the light switch
to AUTO.
Function deactivation: turn the light
switch to a position other than AUTO.
IMPORTANT This function can only be
activated with the ignition device at
MAR.
DIPPED BEAM HEADLIGHTS
With the ignition device on MAR, turn
the switch to. If the dipped beam
headlights are activated, the daytime
lights are switched off and the dipped
beam headlights, side lights and number
plate lights are switched on. The
30J0A0209C
31J0A0888C
31

warning light switches on in the
instrument panel.
DAYTIME RUNNING LIGHTS
(DRL)
"Daytime Running Lights"
(where provided)
19) 20)
With the ignition device turned to MAR
and the light switch turned to positionO
the daytime running/side lights are
automatically activated; the other lights
and interior lighting remain off.
The daytime running lights are
temporarily deactivated when the
direction indicators are activated. When
the direction indicators are deactivated,
the daylight running lights are
reactivated.
FRONT FOG LIGHTS(where provided)
With the ignition device in MAR, with the
side lights and dipped beam headlights
on, press switch
to turn on the fog
lights.
To switch off the fog lights press the
switch again or turn it to positionO.
“Cornering Lights” function
The function activates with the main
beam headlights switched on with a
speed lower than 40 km/h - For widewheel rotation angles or at the switching
on the direction indicator, a light will
turn on (built in the front fog light)
referring to the turning side which will
extend the night visibility angle.
REAR FOG LIGHT
With ignition device in MAR, press thebutton to switch the light on/off.
The rear fog light switches on only when
the dipped beam headlights or fog lights
are switched on. The light switches off by
pressing the
button or by switching off
the main beam headlights or the fog
lights.
PARKING LIGHTS
These can be turned on by turning the
light switch ring to theposition. Thewarning light on the instrument
panel turns on.
IMPORTANT NOTE Do not select this
light switch position when the car is
moving, but only to indicate that the car
is parked when prescribed by the
regulations in force in the country where
you are driving (Highway Code).
To turn the lights off, turn the light
switch ring to theOposition
HEADLIGHTS OFF TIMER
Function activation
It is possible to enable switching on the
lights for the preset time by turning the
ignition device to STOP, with the light
switch ring nut in position
and then
turning the ring nut to positionO.
IMPORTANT To activate this function
the headlights must be deactivated
within 2 minutes after the ignition
device has been taken to STOP.
Automatic function activation
(where provided)
If the car is equipped with a dusk sensor,
it is possible to enable the function
automatically: with the ignition device in
MAR, turn the light switch ring nut to
AUTO, if the sensor reports low light
levels, it will enable the dipped beam
headlights.
The headlights off delay is enabled
automatically when the ignition device is
turned to STOP with the headlights on
for the time selected in the Menu.
Function deactivation
This function is disabled by waiting for
the time set from the Menu, or by turning
the ignition device to the MAR position.
32
GETTING TO KNOW YOUR CAR

If the headlights are switched off before
the ignition, they will switch off normally.
MAIN BEAM HEADLIGHTS
To activate the fixed main beam
headlights, with the ignition device in
MAR, push left lever A fig. 32 (car travel
direction). The light switch should be
turned toAUTOwith the dipped beam
headlights on, or it should be turned to
position
.
To flash, the unstable position is used
(activate by pulling the lever towards
you). With main beam headlights on, the
warning light on the instrument
panel will come on at the same time.
The main beam headlights are
deactivated bringing the lever back to the
central stable position. Warning light
switches off in the instrument panel.Automatic main beam headlights
This function is enabled with the display
Menu or theUconnect™system, and with
the light switch turned to AUTO.
The first time the main beam headlights
are activated (pushing the left lever), the
function is activated (green warning light
comes on in the instrument panel).
If the main beam headlights are actually
on, the blue
warning light will also
come on in the instrument panel.
To deactivate the automatic function
rotate the light switch ring nut to position
.
DIRECTION INDICATORS
Bring left lever A fig. 32 to the (stable)
position:
upwards: activates the right direction
indicator;
downwards: activates the left direction
indicator.
"Lane Change" function
If you wish to signal a lane change, place
the left lever in the unstable position for
less than half a second. The direction
indicator on the side selected will flash
five times and then switch off
automatically.
COURTESY LIGHTS
This function, with the ignition device in
MAR, allows activating the side lights
and the number plate lights for
25 seconds, each time the car is
unlocked with the key with remote
control, or the “Passive Entry” system
(where present).
Enabling the function can be adjusted
through the display Menu or the
Uconnect™system.
The function is automatically disabled
once the activation time elapses
(25 seconds), or when the car doors are
locked again, or by turning the ignition
device to a non-MAR position.
32J0A0063C
33

HEADLIGHT REGULATION
Headlight corrector
It only works with the starter device in
position MAR and the low beams on.
To regulate, turn the A ring fig. 33,
located on the left side of the instrument
panel (left hand drive version) or on the
right side (right hand drive).
Position 0: one or two people in the front
seats;
Position 1: 4 peoplePosition 2: 4 people + load in bootPosition 3: Driver + maximum load
allowed stowed in the boot
IMPORTANT Check the headlight
position every time the load weight is
changed.
INSTRUMENT PANEL AND
CONTROL BUTTON GRAPHIC
BRIGHTNESS ADJUSTMENT
The ring nut is located on the left side
(left hand drive versions) or on the right
side (right hand drive versions) of the
dashboard.
With side lights or headlights on, turn
ring nut B fig. 33 upwards to increase
light brightness of the instrument panel
and of the control button graphics, or
turn the ring nut downwards to decrease
it.
WARNING
19)The daytime running lights are an
alternative to the dipped headlights for
driving during the daytime in countries
where it is compulsory to have lights on
during the day; where it is not compulsory,
the use of daytime running lights is
permitted.20)Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels. The use of
daytime running lights is governed by the
highway code of the country in which you
are driving. Comply with legal
requirements.33J0A0889C
34
GETTING TO KNOW YOUR CAR

KNOWING THE INSTRUMENT PANEL
This section of the booklet gives you all
the information you need to understand,
interpret and use the instrument panel
correctly.EOBD SYSTEM (European On Board
Diagnosis)..................62
CONTROL PANEL AND ON-BOARD
INSTRUMENTS..............63
DISPLAY...................67
TRIP COMPUTER.............70
WARNING LIGHTS AND MESSAGES .71
61

EOBD SYSTEM (European
On Board Diagnosis)
(where provided)
OPERATION
The EOBD system (European On Board
Diagnosis) carries out a continuous
diagnosis of the components of the car
related to emissions.
It also alerts the driver, by switching on
the
warning light on the instrument
panel, together with a message on the
display, when these components are no
longer in peak condition (see “Warning
lights and messages” paragraph in this
chapter).
The aim of the EOBD system (European
On Board Diagnosis) is to:
monitor the efficiency of the system;indicate an increase in emissions;indicate the need to replace damaged
components.
The vehicle also has a connector, which
can interface with appropriate tools, that
makes it possible to read the error codes
stored in the electronic control units
together with a series of specific
parameters for engine operation and
diagnosis. This check can also be carried
out by the traffic police.
IMPORTANT After eliminating a fault,
to check the system completely, a Jeep
Dealership is obliged to run tests and,
if necessary, road tests which may also
require a long journey.
62
KNOWING THE INSTRUMENT PANEL