2018 INFINITI QX60 technical specifications

2. Start the engine and let it idle until itreaches operating temperature, then
turn it off.
3. Remove the oil filler cap
Aby turning it
counterclockwise. 4. Place a large drain pan under the drain
plug
B.
5. Remove the drain plug
Bwith a wrench
by turning it counterclockwise and com-
pletely drain the oil.
If the oil filter is to be changed, remove
and replace it at this time. For additional
information, refer to “Changing engine
oil filter” in this section.
∙ Waste oil must be disposed of properly.
∙ Check your local regulations.
WARNING
∙ Prolonged and repeated contact with
used engine oil may cause skin cancer.
∙ Try to avoid direct skin contact with used oil. If skin contact is made, wash thor-
oughly with soap or hand cleaner as soon
as possible.
∙ Keep used engine oil out of reach of children.
CAUTION
Be careful not to burn yourself. The engine
oil may be hot. 6. Clean and reinstall the drain plug and a
new washer. Securely tighten the drain
plug with a wrench. Do not use excessive
force.
Drain plug tightening torque: 34 N·m (25 ft-lb)
7. Refill engine with recommended oil through the oil filler opening, then install
the oil filler cap securely.
For additional information on drain and
refill capacity, refer to “Recommended
fluids/lubricants and capacities” in the
“Technical and consumer information”
section of this manual.
The drain and refill capacity depends on
the oil temperature and drain time. Use
these specifications for reference only.
Always use the dipstick to determine
when the proper amount of oil is in the
engine.
8. Start the engine. Check for leakage around the drain plug and oil filter. Cor-
rect as required.
9. Turn the engine off and wait more than 10 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
VQ35DD
LDI3013
Maintenance and do-it-yourself8-11

The wheel nuts must be kept tightened to
specifications at all times. It is recommended
that wheel nuts be tightened to specification
at each tire rotation interval.
WARNING
∙ After rotating the tires, check and adjustthe tire pressure.
∙ Retighten the wheel nuts when the ve- hicle has been driven for 1,000 km
(600 miles) (also in cases of a flat tire,
etc.).
∙ Do not include the spare tire in the tire rotation.
∙ Incorrect tire selection, fitting, care or maintenance can affect vehicle safety
with risk of accident and injury.
∙ If in doubt, consult an INFINITI retailer or the tire manufacturer.
∙ Improperly inflated tires can fail sud- denly and cause an accident.
∙ Before taking a long trip, or whenever you heavily load your vehicle, use a tire
pressure gauge to ensure that the tire
pressures are at the specified level.
Tire wear and damage
1. Wear indicator
2. Location mark
WARNING
∙ Tires should be periodically inspected forwear, cracking, bulging or objects caught
in the tread. If excessive wear, cracks,
bulging or deep cuts are found, the tire(s)
should be replaced.
∙ The original tires have built-in tread wear indicators. When the wear indicators are
visible, the tire(s) should be replaced.
∙ Tires degrade with age and use. Have tires, including the spare, over 6 years old
checked by a qualified technician because
some tire damage may not be obvious.
Replace the tires as necessary to prevent
tire failure and possible personal injury.
∙ Improper service of the spare tire may result in serious personal injury. If it is
necessary to repair the spare tire, con-
tact an INFINITI retailer.
Replacing wheels and tires
When replacing a tire, use the same size,
tread design, speed rating and load carrying
capacity as originally equipped. For addi-
tional information, refer to “Wheels and tires”
in the “Technical and consumer information”
section of this manual.
WDI0259
8-36Maintenance and do-it-yourself

9 Technical and consumer information
Recommended fluids/lubricants and capacities....9-2
Fuel Information ..............................9-4
Recommended SAE viscosity number ..........9-4
Air conditioner system refrigerant and
oil recommendations ..........................9-5
Specifications ....................................9-6
Engine ........................................9-6
Wheels and tires ..............................9-7
Dimensions and weights .......................9-7
When traveling or registering in another
country ..........................................9-8
Vehicle identification .............................9-8
Vehicle Identification Number (VIN) plate ......9-8
Vehicle identification number
(chassis number) ..............................9-8 Engine serial number
..........................9-9
Certification plate
(For Gulf standard models) ....................9-9
Tire placard ................................. 9-10
Air conditioner specification label ............9-10
Installing front license plate .....................9-10
Vehicle loading information .....................9-12
Terms ...................................... 9-12
Vehicle load capacity ........................ 9-12
Securing the load ............................ 9-14
Loading tips ................................ 9-15
Measurement of weights ....................9-15
Uniform tire quality grading .....................9-15

ENGINE
ModelVQ35DE/VQ35DD
Type Gasoline, 4-cycle, DOHC
Cylinder arrangement 6-cylinder, V-block, Slanted at 60°
Bore x Stroke mm (in) 95.5 x 81.4 (3.760 x 3.205)
Displacement cm
3(cu in) 3,498 (213.45)
Firing order 1–2–3–4–5–6
Idle speed
No adjustment is necessary.
CVT (in “N” position)
Ignition timing (degree B.T.D.C. at idle speed)
CO%atidle
Spark plug
FXE22HR-11
Spark plug gap (Nominal) mm (in) 1.1 (0.043)
Camshaft operation Timing chain
Maximum vehicle speed (for Gulf Standard Models) km/h (mph) 190 (118)
Maximum vehicle speed:
Gulf Standard regulation requires automobile manufacturers to indicate the maximum vehicle speed for applicable models. The maximum vehicle speed, listed above,
is the measured speed under certain testing conditions. The actual value may differ according to the vehicle usage and road and environmental conditions.
INFINITI recommends you to ALWAYS observe posted speed limits and never drive too fast for conditions.
SPECIFICATIONS
9-6Technical and consumer information

When planning to drive your INFINITI ve-
hicle in another country,you should first find
out if the fuel available is suitable for your
vehicle's engine.
Using fuel with an octane rating that is too
low may cause engine damage. All gasoline
vehicles must be operated with unleaded
gasoline. Therefore, avoid taking your vehicle
to areas where appropriate fuel is not avail-
able.
When transferring the registration of your
vehicle to another country, state, province
or district, it may be necessary to modify the
vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle
emission control and safety standards vary
according to the country, state, province or
district; therefore, vehicle specifications may
differ.
When any vehicle is to be taken into another
country, state, province or district and reg-
istered, its modifications, transportation,
and registration are the responsibility of the
user. INFINITI is not responsible for any in-
convenience that may result.
VEHICLE IDENTIFICATION
NUMBER (VIN) PLATE
The VIN plate is located as shown. This num-
ber is the identification for your vehicle and is
used in the vehicle registration.
The VIN number is also available through the
center display screen. For additional informa-
tion, refer to your “INFINITI InTouch™ Own-
er’s Manual”.
VEHICLE IDENTIFICATION
NUMBER (chassis number)
The vehicle identification number is located
as shown.
TI1050MLTI2028
WHEN TRAVELING OR
REGISTERING IN ANOTHER
COUNTRY VEHICLE IDENTIFICATION
9-8Technical and consumer information