2018 INFINITI QX60 engine oil capacity

2. Start the engine and let it idle until itreaches operating temperature, then
turn it off.
3. Remove the oil filler cap
Aby turning it
counterclockwise. 4. Place a large drain pan under the drain
plug
B.
5. Remove the drain plug
Bwith a wrench
by turning it counterclockwise and com-
pletely drain the oil.
If the oil filter is to be changed, remove
and replace it at this time. For additional
information, refer to “Changing engine
oil filter” in this section.
∙ Waste oil must be disposed of properly.
∙ Check your local regulations.
WARNING
∙ Prolonged and repeated contact with
used engine oil may cause skin cancer.
∙ Try to avoid direct skin contact with used oil. If skin contact is made, wash thor-
oughly with soap or hand cleaner as soon
as possible.
∙ Keep used engine oil out of reach of children.
CAUTION
Be careful not to burn yourself. The engine
oil may be hot. 6. Clean and reinstall the drain plug and a
new washer. Securely tighten the drain
plug with a wrench. Do not use excessive
force.
Drain plug tightening torque: 34 N·m (25 ft-lb)
7. Refill engine with recommended oil through the oil filler opening, then install
the oil filler cap securely.
For additional information on drain and
refill capacity, refer to “Recommended
fluids/lubricants and capacities” in the
“Technical and consumer information”
section of this manual.
The drain and refill capacity depends on
the oil temperature and drain time. Use
these specifications for reference only.
Always use the dipstick to determine
when the proper amount of oil is in the
engine.
8. Start the engine. Check for leakage around the drain plug and oil filter. Cor-
rect as required.
9. Turn the engine off and wait more than 10 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
VQ35DD
LDI3013
Maintenance and do-it-yourself8-11

9 Technical and consumer information
Recommended fluids/lubricants and capacities....9-2
Fuel Information ..............................9-4
Recommended SAE viscosity number ..........9-4
Air conditioner system refrigerant and
oil recommendations ..........................9-5
Specifications ....................................9-6
Engine ........................................9-6
Wheels and tires ..............................9-7
Dimensions and weights .......................9-7
When traveling or registering in another
country ..........................................9-8
Vehicle identification .............................9-8
Vehicle Identification Number (VIN) plate ......9-8
Vehicle identification number
(chassis number) ..............................9-8 Engine serial number
..........................9-9
Certification plate
(For Gulf standard models) ....................9-9
Tire placard ................................. 9-10
Air conditioner specification label ............9-10
Installing front license plate .....................9-10
Vehicle loading information .....................9-12
Terms ...................................... 9-12
Vehicle load capacity ........................ 9-12
Securing the load ............................ 9-14
Loading tips ................................ 9-15
Measurement of weights ....................9-15
Uniform tire quality grading .....................9-15

The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described
in the “Maintenance and do-it-yourself” section to determine the proper refill capacity.
Fluid typeCapacity (approximate) Recommended Fluids/Lubricants
Metric
Measure US
Measure Imperial
Measure
Fuel 74 L 19-1/2 gal 16-1/4 gal • For additional information, refer to “Fuel Information” in this section.
Engine oil*1
Drain and refill
*1: For additional information,
refer to “Engine oil” in the
“Maintenance and do-it-
yourself” section of this manual. With oil
filter change 4.8 L 5-1/8 qt 4-1/4 qt For Mexico
• Genuine “Nissan Motor Oil Ester 5W-30 SN” is recommended.
Except for Mexico
• Genuine “Nissan Motor Oil 0W-20 SN” is recommended.
• If above motor oil is not available, use “NISSAN Motor Oil”
equivalent that matches the following grade and viscosity.
• Oil grade: API SM or SN, ILSAC GF-4 or GF-5
• SAE Viscosity: For additional information, refer to “Recommended
SAE viscosity number” in this section.
Without oil
filter change 4.5 L 4-3/4 qt 4 qt
Engine coolant
(with reservoir) 9.6 L 2-1/2 gal 2-1/8 gal• Genuine NISSAN Engine Coolant (blue) or equivalent.
• Use Genuine NISSAN Engine Coolant or equivalent in tis quality, in
order to avoid possible aluminum corrosion within the engine cooling
system caused by the use of non-genuine engine coolant. Note that
any repairs for the incidents within the engine cooling system while
using non-genuine engine coolant may not be covered the warranty
even if such incidents occurred during the warranty period.
Continuously Variable Transmission (CVT) fluid ———• Genuine NISSAN CVT Fluid NS-3
• Use only Genuine NISSAN CVT Fluid NS-3. Using transmission fluid
other than Genuine NISSAN CVT Fluid NS-3 will damage the CVT,
which is not covered by the warranty.
RECOMMENDED FLUIDS/
LUBRICANTS AND CAPACITIES
9-2Technical and consumer information