2018 INFINITI QX60 set clock

The rain-sensing auto wiper system can au-
tomatically turn on the wipers and adjust the
wiper speed depending on the rainfall and the
vehicle speed by using the rain sensor located
on the upper part of the windshield.
To set the rain-sensing auto wiper system,
place the lever in the AUTO position
1. The
wiper will sweep once while the ignition
switch is in the ON position.
The rain sensor sensitivity level can be ad-
justed by turning the knob toward the front
2(High) or toward the rear3(Low).
– High — High sensitive operation
– Low — Low sensitive operation
To turn the rain-sensing auto wiper system
off, rotate the lever to the OFF position, or
rotate the lever to the LO or HI position.
NOTE:
The Rain Sensor may be disabled. For addi-
tional information, refer to “How to use the
vehicle information display” in this section.
REAR SWITCH OPERATION
WARNING
In freezing temperatures the washer solu-
tion may freeze on the rear window and
obscure your vision which may lead to an
accident. Warm the rear window with the
defogger before you wash the rear window.
CAUTION
∙ Do not operate the washer continuously for more than 30 seconds. ∙ Do not operate the washer if the
windshield-washer fluid reservoir is
empty.
∙ Do not fill the windshield-washer fluid reservoir with windshield-washer fluid
concentrates at full strength. Some
methyl alcohol based windshield-washer
fluid concentrates may permanently
stain the grille if spilled while filling the
windshield-washer fluid reservoir.
∙ Pre-mix windshield-washer fluid concen- trates with water to the manufacturer’s
recommended levels before pouring the
fluid into the windshield-washer fluid
reservoir. Do not use the windshield-
washer fluid reservoir to mix the
windshield-washer fluid concentrate and
water.
If the rear window wiper operation is inter-
rupted by snow, etc., the wiper may stop
moving to protect its motor. If this occurs,
turn the wiper switch to OFF and remove the
snow, etc. on and around the wiper arms.
After about 1 minute, turn the switch on
again to operate the wiper.
The rear window wiper and washer operate
when the ignition switch is in the ON position.
Turn the switch clockwise from the OFF po-
sition to operate the wiper.
LIC3129
Instruments and controls2-37

Example of slot parking (right side)
Stop the vehicle at approximately1mtothe
side of the target and begin the parking pro-
cedure.1. Press the CAMERA button to display the bird’s-eye view.
2. Select “Park Guide”.
3. Select “Backward (R)”. 4. The parking position adjustment screen
will be displayed, showing the clearance
guidelines in red1and the target park-
ing frame in blue
2.
5. Adjust the target parking frame (blue) so that the clearance guidelines (red) do not
overlap with obstacles and set the park-
ing position. Use the up, down, left and
right keys on the screen
3to move the
target parking frame (blue). Use the
clockwise and counterclockwise keys on
the screen
4to rotate the target park-
ing frame (blue). Select “Start”. 6. The starting position frame for backing
up will be displayed in green
1. The
starting position frame is displayed in the
bird’s-eye view and front view.
∙ A green frame indicates the recom- mended position.
∙ A yellow frame indicates that switch- ing will be required.
∙ A red frame indicates that parking is not possible.
LHA4330LHA4331LHA4332
4-14Monitor, climate, audio, phone and voice recognition systems

11. Keep the steering wheel in its currentposition and move the vehicle slowly
backward toward the orange frame. A
chime will sound when the vehicle fits
into the frame. You can adjust the target
parking frame by turning the steering
wheel left or right during backing up.
12. Align the steering wheel and move the vehicle slowly backward toward the tar-
get parking frame.
13. Stop the vehicle.Example of parallel parking
(left side)
Stop the vehicle at approximately1mtothe
side of the target parking position and begin
the parking procedure. 1. Press the CAMERA button to display the bird’s-eye view.
2. Select “Park Guide”.
3. Select "Parallel (L)”. 4. The parking position adjustment screen
will be displayed, showing the clearance
guidelines in red1and the target park-
ing frame in blue
2.
5. Adjust the target parking frame (blue) so that the clearance guidelines (red) do not
overlap with obstacles and set the park-
ing position. Use the up, down, left and
right keys on the screen
3to move the
target parking frame (blue). Use the
clockwise and counterclockwise keys on
the screen
4to rotate the target park-
ing frame (blue).
LHA4335LHA4330LHA4336
4-16Monitor, climate, audio, phone and voice recognition systems