2018 INFINITI QX30 brake light

All of the vehicle's systems remain active when
the engine is switched off automatically.
The engine can be switched off automatically
a maximum of four times (initial stop, then
three subsequent stops) in succession. The
Idle Stop/Start symbol is shown in yel-
low in the vehicle information display after
the engine has been started automatically
for the fourth time. When the
Idle
Stop/Start symbol is shown in green in the
vehicle information display, automatic engine
switch-off is again possible.
NOTE
If the hood is opened while the engine is run-
ning and the Idle Stop/Start function is op-
erational, the engine will switch off auto-
matically.
If the vehicle is brought to a standstill in D or
N, the Idle Stop/Start function switches off
the engine automatically.
AUTOMATIC ENGINE START
The engine is started automatically if:
•You switch off the Idle Stop/Start func-
tion by pressing the ECO button.
•You engage Reverse R or Drive D.
•You unfasten your seat belt or open the
driver's door.
•The vehicle starts to roll.
•The brake system requires this.
•The temperature in the vehicle interior de-
viates from the set range.
•The system detects moisture on the wind-
shield when the air-conditioning system is
switched on.
•The battery's charge status is too low.
The engine is started automatically if you:
•Release the brake pedal in transmission
position D (Drive) or N (Neutral).
•Depress the accelerator pedal.
•Move the transmission out of position P
(Park).
Shifting the transmission to position P (Park)
does not start the engine.
If you
shift the transmission from R (Reverse)
to D (Drive), the Idle Stop/Start function is
available again once the
Idle Stop/Start
symbol reappears in green in the vehicle infor-
mation display.
DEACTIVATING/ACTIVATING
THE IDLE STOP/START
FUNCTION
•To deactivate:press ECO button1. Indi-
cator light
2and theIdle Stop/
Start symbol in the vehicle information dis-
play turn off.
•To activate:press ECO button1. Indica-
tor light
2lights up. If all conditions for
automatic engine switch-off (see "Auto-
matic engine switch-off" earlier in this sec-
tion) are fulfilled, the
Idle Stop/Start
symbol is shown in green in the vehicle
information display.
NIC2633
5-30Starting and driving

•The system will not operate at speeds be-
low approximately 40 MPH (60 km/h) or
if it cannot detect lane markers.
•The LDW system is primarily intended
for use on well-developed freeways or
highways. It may not detect the lane
markers in certain roads, weather or
driving conditions.
•Do not use the LDW system under the
following conditions as it may not func-
tion properly:
–During bad weather (rain, fog, snow,
etc.).
–When driving on slippery roads, such
as on ice or snow, etc.
–When driving on winding or uneven
roads.
–When there is a lane closure due to
road repairs.
–When driving in a makeshift or tem-
porary lane.
–When driving on roads where the lane
width is too narrow.
–When driving without normal tire
conditions (for example, tire wear,
low tire pressure, installation of
spare tire, tire chains, non-standard
wheels).–When the vehicle is equipped with
non-original brake parts or suspen-
sion parts.
•The camera may not detect lane markers
in the following situations and the LDW
system may not operate properly.
–On roads where there are multiple
parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; non-
standard lane markers; or lane mark-
ers covered with water, dirt, snow,
etc.
–On roads where the discontinued lane
markers are still detectable.
–On roads where there are sharp
curves.
–On roads where there are sharply
contrasting objects, such as shad-
ows, snow, water, wheel ruts, seams
or lines remaining after road repairs.
(The LDW system could detect these
items as lane markers.)
–On roads where the traveling lane
merges or separates.
–When the vehicle’s traveling direc-
tion does not align with the lane
marker.–When traveling close to the vehicle in
front of you, which obstructs the lane
camera unit detection range.
–When rain, snow or dirt adheres to
the windshield in front of the lane
camera unit.
–When the headlights are not bright
due to dirt on the lens or if the aiming
is not adjusted properly.
–When strong light enters the lane
camera unit. (For example, the light
directly shines on the front of the ve-
hicle at sunrise or sunset.)
–When a sudden change in brightness
occurs. (For example, when the ve-
hicle enters or exits a tunnel or under
a bridge.)
–When there is poor visibility. (For ex-
ample, due to insufficient illumina-
tion of the road, or due to snow, rain,
fog or spray.
–When there is glare. (For example,
from oncoming traffic, the sun or re-
flection when the road is wet).
5-34Starting and driving

RADAR MAINTENANCE
The two radar sensor unitsAfor the BSW
system are located near the rear bumper.
Always keep the area near the radar sensors
clean.
The radar sensors may be blocked by tempo-
rary ambient conditions such as splashing
water, mist or fog.
The blocked condition may also be caused by
objects such as ice, frost or dirt obstructing
the radar sensors.
Check for and remove objects obstructing
the area around the radar sensors.
Do not attach stickers (including transparent
material), install accessories or apply addi-
tional paint near the radar sensors.Do not strike or damage the area around the
radar sensors. It is recommended you consult
an INFINITI retailer if the area around the
radar sensors is damaged due to a collision.
FCC NOTICE
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.
NOTE
Changes or modification not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause harmful interfer-
ence, and (2) this device must accept any
interference received, including interference
that may cause undesired operation of the
device.Cruise control maintains a constant road
speed for you. It brakes automatically in order
to avoid exceeding the set speed. You must
select a lower gear in good time on long and
steep downhill gradients, especially if the ve-
hicle is laden or towing a trailer.WARNING
For vehicles with automatic transmission,
you need to have selected manual drive
program M (see "Manual drive program"
earlier in this section). By doing so, you will
make use of the braking effect of the en-
gine. This relieves the load on the brake
system and prevents the brakes from over-
heating and wearing too quickly.
Use cruise control only if road and traffic
conditions are appropriate for maintaining a
steady speed for a prolonged period. You can
set the cruise control at any road speed
above 20 MPH (30 km/h).
The speed indicated in the speedometer may
differ slightly from the set speed.
NAA1640
CRUISE CONTROL
5-46Starting and driving

vehicle as necessary and if the vehicle ahead
comes to a stop, the vehicle decelerates to a
standstill. However, the ICC system can only
apply up to 50% of the vehicle’s total braking
power. This system should only be used when
traffic conditions allow vehicle speeds to re-
main fairly constant or when vehicle speeds
change gradually. If a vehicle moves into the
traveling lane ahead or if a vehicle traveling
ahead rapidly decelerates, the distance be-
tween vehicles may become closer because
the ICC system cannot decelerate the vehicle
quickly enough. If this occurs, the ICC system
will sound a warning chime and illuminate the
distance warning light to notify the driver to
take necessary action.
The following items are controlled in the ICC
system:
•When there are no vehicles traveling
ahead, the ICC system maintains the
speed set by the driver. The set speed
range is between approximately 20 and
125 MPH (30 and 200 km/h).
•When there is a vehicle traveling ahead,
the ICC system adjusts the speed to main-
tain the distance, selected by driver, from
the vehicle ahead. The adjusting speed
range is up to the set speed. If the vehicle
ahead comes to a stop, the vehicle decel-
erates to a standstill within the limitations
of the system. Once the vehicle is station-
ary, it remains stationary and you do not
need to depress the brake pedal.
•When the vehicle traveling ahead has
moved out from its lane of travel, pull the
cruise control lever or push the accelerator
pedal briefly. The ICC system accelerates
and maintains vehicle speed up to the set
speed.
The ICC system does not control vehicle
speed or warn you when you approach sta-
tionary and slow moving vehicles. You must
pay attention to vehicle operation to main-
tain proper distance from vehicles ahead
when approaching toll gates or traffic con-
gestion.
ICC SWITCH (CRUISE CONTROL
LEVER)
1Store the current speed or a higher speed
2Set the specified minimum distance
3Store the current speed or call up the last
stored speed
4Store the current speed or a lower speed
5Deactivate the ICC system
The ICC system is operated by the cruise
control lever, located on the steering column.
NSD582A
Starting and driving5-51

OPERATING ICC
To set cruising speed, accelerate your vehicle
to the desired speed and quickly push the
cruise control lever, up
1or down4. Take
your foot off the accelerator pedal. Your ve-
hicle will maintain the set speed.
NOTE
If you do not fully release the accelerator
pedal, the [ICC Suspended] message ap-
pears in the vehicle information display. The
set distance to a slower-moving vehicle in
front will then not be maintained. You will be
driving at the speed you determine by the
position of the accelerator pedal.
You can also activate the ICC when station-
ary. The lowest speed that can be set is
20 MPH (30 km/h ).
System operation
The driver sets the desired vehicle speed
based on the road conditions. The ICC sys-
tem maintains the set vehicle speed, similar to
standard cruise control, as long as no vehicle
is detected in the lane ahead. The ICC system
displays the set speed for 5 seconds after the
cruise control lever is activated.
Vehicle detected ahead:
When a vehicle is detected in the lane ahead,
the ICC system decelerates the vehicle by
controlling the throttle and applying the
brakes to match the speed of a slower vehicle
ahead. The system then controls the vehicle
speed based on the speed of the vehicle
ahead to maintain the driver selected dis-
tance.The brake lights of the vehicle come on when
braking is performed by the ICC system.
When the brake operates, a noise may be
heard. This is not a malfunction.
When a vehicle ahead is detected, the vehicle
ahead symbol
1appears in the vehicle infor-
mation display.
Vehicle ahead not detected:
When a vehicle is no longer detected ahead,
the ICC system gradually accelerates your
vehicle to resume the previously set vehicle
speed. The ICC system then maintains the set
speed.
When a vehicle is no longer detected, the
vehicle ahead display turns off
2.
NSD582ANSD615
System set display with vehicle ahead
NSD616
System set display without vehicle ahead
Starting and driving5-53

If a vehicle ahead appears during accelera-
tion to the set vehicle speed or any time the
ICC system is in operation, the system con-
trols the distance to that vehicle.
Changing lanes to pass another
vehicle:
When you changes lane to pass another ve-
hicle, ICC supports the action if:
•The vehicle speed is more than 45 MPH
(70 km/h)
•The ICC is maintaining the distance to a
vehicle in front
•The respective turn signal is activated
If these conditions are met, the vehicle will be
accelerated. Acceleration will be interrupted
if changing lanes takes too long or if the
distance between your vehicle and the ve-
hicle in front becomes too small.
How to change the set vehicle
speed
To cancel the preset speed, use any of these
methods:
•Tap the brake pedal when the vehicle is
moving.
•Quickly push the cruise control lever in the
direction of arrow
5.
The message [ICC OFF] appears in the ve-
hicle information display for 5 seconds.
To reset at a higher cruising speed, use one of
the following methods:
•Depress the accelerator pedal. When the
vehicle attains the desired speed, quickly
pull the cruise control lever towards you
3.
•Pull the cruise control lever up1beyond
the pressure point. The set vehicle speed
will increase by approximately 10 MPH
(10 km/h).
•Pull the cruise control lever up (1) at the
pressure point. The set vehicle speed will
increase by approximately 1 MPH (1 km/h).
To reset at a lower cruising speed, use one of
the following methods:
•Lightly tap the brake pedal. When the ve-
hicle attains the desired speed, quickly pull
the cruise control lever towards you
3.
•Pull the cruise control lever down4be-
yond the pressure point. The set vehicle
speed will decrease by approximately
10 MPH (10 km/h).
•Pull the cruise control lever down4to the
pressure point. The set vehicle speed will
decrease by approximately 1 MPH (1 km/h).
To resume the preset speed, quickly pull the
cruise control lever towards you
4. The ve-
hicle will resume the last set cruising speed
when the vehicle speed is over 20 MPH
(30 km/h).
NOTE
If you do not fully release the accelerator
pedal, the [ICC Deactivated Automatically]
message appears in the vehicle information
NSD582A
5-54Starting and driving

Approach warning
If your vehicle comes closer to the vehicle
ahead due to rapid deceleration of that ve-
hicle or if another vehicle cuts in, the system
warns the driver with the chime and distance
warning light. Decelerate by depressing the
brake pedal to maintain a safe vehicle dis-
tance if:
•The chime sounds.
•The distance warning light is illuminated.
The warning chime may not sound and the
distance warning light may not illuminate in
some cases when there is a short distance
between vehicles. Some examples are:
•When the vehicles are traveling at the
same speed and the distance between ve-
hicles is not changing. In this case, the
distance warning light will be on.
•When the vehicle ahead is traveling faster
and the distance between vehicles is in-
creasing.
•When a vehicle cuts in near your vehicle
•The warning chime will not sound and the
distance warning light will not illuminate
when:
– The vehicle approaches other vehicles
that are parked or moving slowly.– The accelerator pedal is depressed,
overriding the system.
Also, the sensor sensitivity can be affected by
vehicle operation (steering maneuver or driv-
ing position in the lane) or traffic or vehicle
condition (for example, if a vehicle is being
driven with some damage).
Automatic cancellation
A chime sounds and the message [ICC off] is
displayed in the vehicle information display
for 5 seconds under the following conditions
and the control is automatically canceled.
•The electric parking brake is applied.
•The VDC intervenes or the VDC is deacti-
vated.
•The P (Park), R (Reverse) or N (Neutral)
position is engaged.
•The cruise control lever is pulled in order to
pull away but the front passenger door or
one of the rear doors is open.
•The vehicle is skidding or a wheel slips.
•Active Park Assist is activated.
ICC LIMITATIONS
WARNING
Listed below are the system limitations for
the ICC system. Failure to operate the ve-
hicle in accordance with these system limi-
tations could result in serious injury or
death.
•This system is only an aid to assist the
driver and is not a collision warning or
avoidance device. It is the driver’s re-
sponsibility to stay alert, drive safely
and be in control of the vehicle at all
times.
•The system is primarily intended for use
on straight, dry, open roads with light
traffic. It is not advisable to use the sys-
tem in city traffic or congested areas.
•This system will not adapt automati-
cally to road conditions. This system
should be used in evenly flowing traffic.
Do not use the system on roads with
sharp curves, or on icy roads, in heavy
rain or in fog.
5-56Starting and driving

The FEB system uses a radar sensorAlo-
cated behind the INFINITI logo to measure
the distance to the vehicle ahead in the trav-
eling lane.
FEB SYSTEM OPERATION
1Steering wheel mounted controls (left side)
2Distance warning light
3Forward emergency braking OFF displayThe FEB system consists of a distance warn-
ing function with an autonomous emergency
braking function and adaptive brake assist
function.
NSD645
NSD624
Starting and driving5-63