2018 INFINITI QX30 oil capacity

1. Park the vehicle on a level surface and
apply the parking brake.
2. Start the engine and let it idle until it
reaches the normal operating tempera-
ture, then turn it off.
3. Remove the oil filler cap by turning it
counterclockwise.
4. Remove the engine undershield.
5.
Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by
turning it counterclockwise and com-
pletely drain the oil. If the oil filter is to be
changed, remove and replace it at this
time. For additional information, refer to
"Changing engine oil filter" later in this
section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a
new washer. Securely tighten the drain
plug with a wrench. Do not use excessive
force.
Drain plug tightening torque: 22 ft-lb,
30 N•m
8. Refill engine with recommended oil
through the oil filler opening, then install
the oil filler cap securely.
For additional information on drain and
refill capacity, refer to "Recommended
fluids/lubricants and capacities".
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always
use the dipstick to determine when the
proper amount of oil is in the engine.
9. Start the engine. Check for leakage
around the drain plug and oil filter. Correct
as required.
10. Turn the engine off and wait more than
15 minutes. Check the oil level with the
dipstick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and
apply the parking brake.
2. Turn the engine off and wait more than
15 minutes.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise.
Then remove the oil filter by turning it by
hand.
CAUTION
Be careful not to burn yourself. The engine
oil may be hot.
NDI1622NDI1610
2.0L gasoline engine
8-6Do-it-yourself

10 Technical information
Recommended fluids/lubricants and capacities . .10-2
Fuel recommendation................10-3
Engine oil and oil filter recommendations. . . .10-5
Air conditioner system refrigerant and oil
recommendations...................10-6
Engine specifications...................10-7
Wheels and Tires.....................10-8
Dimensions.........................10-8
When traveling or registering in another
country...........................10-9
Vehicle identification...................10-9
Vehicle identification number (VIN) plate. . . .10-9
Vehicle identification number (chassis
number)........................10-10
Engine serial number................10-10
F.M.V.S.S./C.M.V.S.S. Certification label . . .10-10
Emission control information label.......10-11
Tire and loading information label........10-11
Air conditioner specification label........10-11Installing front license plate..............10-12
Vehicle loading information..............10-13
TERMS........................10-13
Vehicle load capacity................10-14
Loading tips......................10-15
Measurement of weights.............10-15
Trailer towing......................10-15
Uniform tire quality grading..............10-16
Treadwear......................10-16
Traction AA, A, B and C..............10-16
Temperature A, B and C..............10-16
Emission control system warranty..........10-17
Reporting safety defects................10-17
Readiness for inspection/maintenance (I/M)
test.............................10-18
Event data recorders (EDR) (if so equipped) . . .10-19
Owner's manual/service manual order
information........................10-19

The following are approximate capacities. The actual refill quantities may be slightly different. When refilling, follow the procedures instructed
in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Fluid type Capacity (approximate) Recommended Fluids/Lubricants
Metric Measure US measure Imperial Measure
Fuel tank 50 L
(4WD: 56 L)13.2 gal
(4WD: 14.8 gal11 gal
(4WD: 12.3 gal)
–See "Fuel recommendation" later in this section.
Engine oil (*)
Drain and refill with oil filter
change5.6 L 6 qt 5 qt The approximate capacities listed are for refilling during an engine oil change. *:
For additional information, see "Changing engine oil".
2.0L gasoline engine:
–Engine oil meeting specification MB229.5, viscosity SAE 0W-30 or equivalent–As an alternative to this recommended oil, engine oils meeting specification
MB229.5, viscosity SAE 0W-40, 5W-30 and 5W-40 may be used and meet
all specifications and requirements necessary to maintain the new vehicle
limited warranty.
For additional information, see "Engine oil and oil filter recommendations" later in
this section.
Cooling system
with Reservoir7.6 8.1 qt 6.7 qt
–Genuine INFINITI Engine Coolant or equivalent in its quality
BASF Glysantin® G40®
–Use Genuine INFINITI Engine Coolant, or equivalent in its quality, in order to
avoid possible aluminum corrosion within the engine cooling system caused by
the use of non-genuine engine coolant.Note that any repairs for incidents
with the engine cooling system while using non-genuine engine coolant may
not be covered by the warranty even if such incidents occurred during the
warranty period.
Automatic Transmission
Fluid (ATF)6.21 L 6.6 qt 5.5 qt Shell DCT-M1
Brake fluid Refill to the proper fluid level accord-
ing to the instructions in the “8. Main-
tenance and do-it-yourself” section.
–Genuine INFINITI brake fluid DOT4+ or equivalent.–Never mix different types of fluids.
Differential gear oil 0.74 L 0.8 qt 0.65 qt
–Castrol BOT 355 75W-85
Multi-purpose grease — — —
–NLGI No. 2 (Lithium soap base)
RECOMMENDED FLUIDS/
LUBRICANTS AND CAPACITIES
10-2Technical information

Fluid type Capacity (approximate) Recommended Fluids/Lubricants
Metric Measure US measure Imperial Measure
Air conditioner system
refrigerant—— —
–HFC-134a
Air conditioner system
lubricant—— —
–INFINITI A/C System Oil Type S or equivalent
FUEL RECOMMENDATION
INFINITI recommends the use of unleaded
premium gasoline with an octane rating of at
least 91 AKI (Anti-Knock Index) number (Re-
search octane number 95).
If unleaded premium gasoline is not available,
unleaded regular gasoline with an octane rat-
ing of at least 89 AKI number (Research oc-
tane number 93) may be temporarily used,
but only under the following precautions:
•Have the fuel tank filled only partially with
unleaded regular gasoline, and fill up with
unleaded premium gasoline as soon as
possible.
•Avoid full throttle driving and abrupt ac-
celeration.
Use unleaded premium gasoline for maxi-
mum vehicle performance.
CAUTION
•Using a fuel other than that specified
could adversely affect the emission con-
trol system, and may also affect war-
ranty coverage.
•Under no circumstances should a leaded
gasoline be used, because this will dam-
age the three-way catalyst.
•Do not use E-15 or E-85 fuel in your
vehicle. Your vehicle is not designed to
run on E-15 or E-85 fuel. Using E-15 or
E-85 fuel in a vehicle not specifically de-
signed for E-15 or E-85 fuel can ad-
versely affect the emission control de-
vices and systems of the vehicle.
Damage caused by such fuel is not cov-
ered by the INFINITI New Vehicle Lim-
ited Warranty.
•Do not use fuel that contains the octane
booster methylcyclopentadienyl man-
ganese tricarbonyl (MMT). Using fuel
containing MMT may adversely affect
vehicle performance and vehicle emis-
sions. Not all fuel dispensers are labeled
to indicate MMT content, so you may
have to consult your gasoline retailer for
more details. Note that Federal and
California laws prohibit the use of MMT
in reformulated gasoline.
•U.S. government regulations require
ethanol dispensing pumps to be identified
by a small, square, orange and black label
with the common abbreviation or the ap-
propriate percentage for that region.
Gasoline specifications
INFINITI recommends using gasoline that
meets the World-Wide Fuel Charter
(WWFC) specifications where it is available.
Technical information10-3