2018 FIAT 500 manual transmission

READ THIS CAREFULLY
REFUELLING
Petrol engines: Only refuel with unleaded petrol with octane rating (RON) not less than 95, in compliance with the European
specification EN228. Do not use petrol containing methanol or ethanol E85. Using these mixtures may cause misfiring and driving
issues, as well as damage fundamental components of the supply system.
Diesel engines: refuel only with Diesel fuel motor vehicles conforming to the European specification EN590. The use of other
products or mixtures may damage the engine beyond repair and consequently invalidate the warranty, due to the damage caused.
For further details on the use of the correct fuel see the “Refuelling the vehicle” paragraph in the “Starting and driving” chapter.
STARTING THE ENGINE
Versions with manual gearbox (petrol engines): make sure that the handbrake is engaged, put the gear in neutral, fully
depress the clutch without pressing the accelerator, then turn the ignition key to AVV and release it as soon as the engine has
started.
Versions with manual gearbox (diesel engines): make sure that the handbrake is engaged, put the gear in neutral, fully
depress the clutch pedal without pressing the accelerator, then turn the ignition key to MAR and wait for the
mwarning
lights to switch off. Turn the ignition key to AVV and finally release it as soon as the engine starts.
Versions with automatic transmission: make sure that the handbrake is engaged and that the gear lever is in P (Parking) or N
(Neutral), fully depress the brake pedal, then turn the ignition key to AVV.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter develops high temperatures during operation. Do not park the car on grass, dry leaves, pine needles or
other flammable material: fire hazard.
RESPECTING THE ENVIRONMENT
The vehicle is fitted with a system that carries out a continuous diagnosis of the emission-related components in order to help
protect the environment.
ELECTRICAL ACCESSORIES
If, after buying the vehicle, you decide to add electrical accessories (with the risk of gradually draining the battery), contact a Fiat
Dealership. They can calculate the overall electrical requirement and check that the electric system of the vehicle can support the
required load.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring that it maintains its performance and its safety features, its environmental
friendliness and low running costs for a long time to come.
K



STARTING AND DRIVING
120
PARKING THE
VEHICLE
When parking and leaving the car,
proceed as follows:
❒ engage a gear (1st gear if facing
uphill or reverse if facing downhill)
and leave the wheels turned;
❒ stop the engine and engage the
handbrake;
❒ always remove the key from the
starter switch.
Block the wheels with a wedge or a
stone if the car is parked on a steep
slope.
On versions equipped with automatic
transmission, wait for the letter P to be
displayed before releasing the brake
pedal.
IMPORTANT NEVER leave the car with
the gearbox in neutral (or, on versions
equipped with automatic transmission,
before putting the shift lever at P).
HANDBRAKE 27)
The handbrake lever fig. 86 is located
between the two front seats.
To use the handbrake pull the lever
upwards until the car cannot be
moved.
To release the handbrake, raise the
lever slightly and press the release
button A fig. 86; hold down the button
and lower the lever.
86DVDF0S162c
USING THE MANUAL
GEARBOX
28) 14)
To engage the gears, press the clutch
pedal fully and put the gear lever into
one of the required positions (the
diagram is shown on the knob fig. 87).
For cars provided with 6-speed
gearbox, to engage the 6
thgear,
operate the lever by pressing it
towards the right in order to avoid
engaging the 4
thgear by mistake. The
same applies to shifting from 6thto 5th
gear.
87DVDF0S0156c

121
IMPORTANT Reverse can only be
engaged when the vehicle is
completely stationary. With the engine
running, wait for at least 2 seconds
with the clutch pedal fully pressed
before engaging reverse to prevent
damage to the gears and grating.
To engage reverse R from neutral, lift
the sliding ring A-fig. 87 under the
knob and shift the lever to the right and
back.
IMPORTANT The clutch pedal should
be used only to change gear. Do not
drive with your foot resting on the
clutch pedal, however lightly. For
versions/markets, where provided, the
electronic clutch control could cut in,
interpreting the incorrect driving style
as a fault.USING THE
DUALOGIC
GEARBOX 14)
(for versions/markets, where provided)
OPERATING MODE
The gearbox/transmission can function
in two operating modes:
❒ MANUAL the driver decides when
to shift gear;
❒ AUTO the system decides when to
shift gear.
MANUAL MODE
❒ Press the brake pedal and start the
engine.
❒ Push the gear lever A-fig. 88
towards (+) to engage the first gear
(if it is coming from N or R, simply
place the lever in the middle
position) or in R to engage reverse
gear.
❒ Release the brake pedal and press
the accelerator pedal.
❒ In driving conditions, push lever A of
the gearbox towards (+) to engage
the next gear up or towards (–) to
engage the next gear down.
AUTO MODE
❒ Press the brake pedal and start the
engine.
❒ Push the gear lever to A/M to
engage automatic mode or to R to
engage reverse gear.
❒ Release the brake pedal and press
the accelerator pedal.
88DVDF0S0192c

STARTING AND DRIVING
126
SETTING THE
DESIRED SPEED
Proceed as follows:
❒ activate the device by turning the
ring C fig. 95 downwards.
❒ when the vehicle has reached the
desired speed, turn the ring B fig. 95
upwards (or downwards) and release it
to activate the device. When the
accelerator is released, the vehicle will
automatically maintain the selected
speed.
If needed (e.g. when overtaking), you
can increase speed simply by pressing
the accelerator; when you release the
pedal, the vehicle goes back to the
speed stored previously.
When travelling downhill with the device
active, the vehicle speed may slightly
exceed the set one.
WARNING Before turning the ring B
upwards or downwards, the vehicle
must travel at a constant speed on
level ground.
INCREASING THE SPEED
Once the electronic Cruise Control has
been activated, the speed can be
increased by turning the ring B
upwards.
DECREASING SPEED
To decrease the speed with the device
activated, turn the ring B downwards.
RECALLING THE SPEED
For versions with Dualogic transmission
operating in D (Drive - automatic)
mode, press and release the
CANC/RES A button (fig. 95).
For versions with manual or Dualogic
transmission in sequential mode,
before recalling the previously set
speed you should accelerate to get
close to it, then press and release the
CANC/RES A button.
DEACTIVATING
THE DEVICE
Lightly pressing the brake pedal or
pressing the CANC button deactivates
the electronic Cruise Control without
deleting the stored speed.
Changing gear deactivates the Cruise
Control.
DEACTIVATING
THE DEVICE
The electronic Cruise Control is
disabled by turning the ring
C fig. 95 to the 0 position or putting the
starter switch at STOP.