2018 FIAT 500 Time

IN AN EMERGENCY
138
SIDE LIGHTS / DAYTIME
RUNNING LIGHTS
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder B fig. 116
anticlockwise and remove it;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder B by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
DIRECTION INDICATORS
Front (POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder A fig. 117
anticlockwise and pull it out;
❒ remove the snap-fitted bulb and
replace it;
❒ refit the bulb holder A by turning it
clockwise and locking it correctly;
❒ reinstall the rubber cap.
117DVDF0S0116c
Front (Excluding POP versions)
To replace the bulb, proceed as
follows:
❒ remove the protecting rubber cap
mentioned above;
❒ turn the bulb holder anticlockwise
and remove it;
❒ replace the bulb
bulb holder assembly;
❒ refit the bulb holder in its housing
A fig. 118 by turning it clockwise
and locking it correctly;
❒ refit the protection cap in its housing
and turn anticlockwise.
118DVDF0S0198c

IN AN EMERGENCY
142
FuseAmpereDescription
F13 5 •
Left dipped headlight and headlight alignment control unit power supply
F36 15 Diagnosis socket, radio, climate control, EOBD
F37 5 Brake light switch, instrument panel node
F38 15 Central door locking
F43 15 Windscreen/rear window washer pump
F47 20 Driver’s side power window
F48 20 Passenger’s side power window
F49 5 Parking sensor, control backlighting, electric mirrors
F51 7.5 Climate control, brake lights, clutch, sunroof, electric mirrors
F53 5 Instrument panel node
•
For versions/markets, where provided
ENGINE COMPARTMENT
JUNCTION BOX
The fuse box is located on the right
side of the engine compartment.
To access the fuses, proceed as
follows:
❒ Fully press the screw A fig. 130;
❒ at the same time slowly rotate the
screw anticlockwise, until resistance
is encountered (do not overtighten);
❒ slowly release the screw;
❒ opening is indicated by the entire
screw head coming out of its
housing;
❒ remove cover B, sliding it upwards
on the side guides, as indicated in
the figure.
❒ after replacing the fuse, refit the
cover, making sure that it is closed
properly.
130DVDF0S0201c

IN AN EMERGENCY
144
IF THE BATTERY IS
FLAT36)
IMPORTANT The battery recharging
procedure is provided for information
purposes only. You are advised to
contact a Fiat Dealership to have this
operation carried out.
IMPORTANT After turning the ignition
key to STOP and having closed the
driver’s side door, wait at least one
minute before disconnecting the battery
and then reconnecting the electrical
supply to the battery.
Charging should be slow at a low
ampere rating for approximately 24
hours. Charging for a longer time may
damage the battery.
Versions without Start&Stop
(for versions/markets, where provided)
To recharge, proceed as follows:
❒ disconnect the terminal from the
negative battery pole;
❒ connect the charger cables to the
battery terminals, making sure that
polarities are correct;
❒ turn on the charger;
❒ when you have finished, turn the
charger off before disconnecting the
battery;
❒ reconnect the terminal to the
negative battery pole.
Versions with Start&Stop
(for versions/markets, where provided)
To recharge, proceed as follows:
❒ disconnect the connector A fig. 132
(pressing the button B) from the
sensor C monitoring the battery
charge status, on the negative pole
D of the battery;
132DVDF0S0127c
❒ connect the positive cable of the
battery charger to the positive
battery pole E fig. 133 and the
negative cable to the terminal of
sensor D;
❒ turn on the charger. At the end of
the charging process, switch the
battery charger off;
❒ after having disconnected the
battery charger, reconnect
connector A to the sensor C as
shown in fig. 132.
133DVDF0S0128c

147
SERVICING AND CARE
SCHEDULED SERVICING
Correct servicing is crucial for
guaranteeing a long life for the vehicle
under the best conditions.
For this reason, Fiat has planned a
series of checks and services at fixed
distance intervals and, for
versions/markets, where provided, at
fixed time intervals, as described in the
Scheduled Servicing Plan.
Regardless of the above, it is always
necessary to carefully follow the
instructions in the Scheduled Servicing
Plan (e.g. periodically check level of
liquids, tyre pressure, etc.).
Scheduled Servicing is offered by all
Fiat Dealerships according to fixed
time or kilometres/miles intervals.
If, during each operation, in addition to
the ones scheduled, the need arises
for further replacements or repairs,
these may be carried out with the
owner’s explicit agreement only. If your
vehicle is used frequently for towing,
the interval between one service
operation and the next should be
reduced. IMPORTANT NOTES
Scheduled Servicing interventions are
set out by the Manufacturer. Failure to
have them carried out may invalidate
the warranty.
We advise you to inform a Fiat
Dealership of any small operating
irregularities without waiting for the
next service.

163
The instructions for good preservation
follow below:
❒ avoid washing with rollers and/or
brushes in washing stations.
Then, wash the vehicle, only by
hand, using pH-neutral detergents;
dry it with a wet chamois leather.
Abrasive products and/or polishes
should not be used for cleaning the
vehicle.
❒ Bird droppings must be washed off
immediately and thoroughly as the
acid they contain is particularly
aggressive.
❒ Avoid (if at all possible) parking the
vehicle under trees; remove
vegetable resins immediately as,
when dried, it may only be possible
to remove them with abrasive
products and/or polishes, which is
highly inadvisable as they could alter
the typical opacity of the paint.
❒ Do not use pure windscreen washer
fluid for cleaning the front
windscreen and rear screen; dilute it
by at least 50% in water.
Some versions are fitted with exclusive
decorations on the door mirror covers;
do not use pressurised or high-
temperature jets of water when washing
them.Versions with stickers or wrapping
4)
To correctly clean and wash the car,
proceed as follows:
❒ Avoid washing with rollers and/or
brushes in washing stations.
Then, wash the vehicle, only by
hand, using pH-neutral detergents;
dry it with a wet chamois leather.
Abrasive products and/or polishes
should not be used for cleaning the
vehicle.
❒ If high pressure jets or cleaners are
used to wash the vehicle, hold at
least 40 cm away from the
bodywork to avoid damage or
alteration. It should be remembered
that the build up of water can
damage the car over a period of
time;
❒ Wash the bodywork using a low
pressure jet of water;
❒ Use a sponge to wipe a slightly
soapy solution over the bodywork,
frequently rinsing the sponge;
❒ Rinse with plenty of water and dry
with a jet of air or a chamois leather.
Dry the less visible parts with special
care, such as the door frames,
bonnet and the headlight frames,
where water may stagnate more
easily. The car should not be taken
to a closed area immediately, but
left outside so that residual water
can evaporate.
Do not wash the car after it has been
parked in the sun.
Exterior plastic parts must be cleaned
in the same way as the rest of the
vehicle.
Where possible, do not park under
trees; the resinous substances that
many species release give the paint a
dull appearance and increase the
possibility of triggering rusting
processes.
IMPORTANT Bird droppings must be
washed off immediately and thoroughly
as the acid they contain is particularly
aggressive.

IMPORTANT INFORMATION AND RECOMMENDATIONS
188(CONTINUES)
PERSONAL SAFETY
(CONTINUED)
7) DAYTIME RUNNING LIGHTS (DRL)
•The daytime running lights are an alternative to the dipped
beam headlights for driving during the daytime in countries
where it is compulsory to have lights on during the day, and
they are also permitted in those countries where this is not
obligatory.
•Daytime running lights cannot replace dipped beam
headlights when driving at night or through tunnels.
•The use of daytime running lights is governed by the highway
code of the country in which you are driving. Comply with legal
requirements.
8) FUEL CUT-OFF SYSTEM
If, after an impact, you smell fuel or notice leaks from the fuel
system, do not reactivate the system to avoid the risk of fire.
9) INTERIOR FITTINGS
•The cigar lighter gets extremely hot. Handle it with caution and
do not allow it to be used by children to avoid the risk of fire or
burns. Always check that the cigar lighter has switched off.
•Only accessories with a maximum power of 180 W (maximum
absorption 15 A) can be connected to the socket.
•Never travel with the glove compartment open: it could injure
the passenger in the event of a crash.
•On both sides of the passenger side sun visor there is a label
remembering that it is compulsory to deactivate the airbags if a
rearward facing child restraint system is fitted.
Always comply with the instructions on the label.10) SUNROOF – ELECTRIC SOFT TOP
ELECTRIC WINDOWS
When leaving the car, always remove the key from the ignition
device to avoid the risk of injury to the vehicle occupants due to
accidental operation of these devices: improper use can be
dangerous. Before and during operation, always check that
nobody is exposed to the risk of being injured either directly by
the moving window or through objects getting
caught or hit by it.
11) SOFT TOP
•Keep hands away from the soft top mechanism while opening
and closing the soft top or if the soft top stops in a position before
the cycle is completed to prevent damage and injury.
•Keep children away from the area in which the top is folding
during opening or closing operations.
12) DOORS
Before opening a door, ensure that you can do it in conditions of
safety. Open the doors only when the vehicle is stationary.
13) LUGGAGE COMPARTMENT
•Never exceed the maximum allowed load in the luggage
compartment, see chapter “Technical specifications”. Also make
sure that the objects you place in the luggage compartment have
been properly secured, to avoid them from being thrown forward
consequent to sudden braking and injuring your passengers.
•Do not drive with the tailgate open as exhaust fumes may enter
the vehicle.
•If you are travelling in areas with few filling stations and you
want to transport fuel in a spare tank, comply with the law by
using only an approved, suitably secured tank. In the event of a
collision the fire risk is increased all the same.

189(CONTINUES)
PERSONAL SAFETY
(CONTINUED)
•When opening the tailgate, take care not to hit possible
objects on the roof rack.
•Make sure the backrests are properly secured at both sides
to prevent them from moving forward, in the event of sharp
braking, with possible impact with of the passengers.
14) ROOF RACK/SKI RACK
•Fully comply with the regulations in force concerning
maximum clearance.
•Never exceed the maximum permitted loads; see chapter
“Technical specifications”.
•Evenly distribute the load and take into account, when
driving, the increased responsiveness of the vehicle to side
wind. After travelling for a few kilometres, check to ensure that
the fixing screws for the attachments are well tightened.
•Before driving, make sure that the transversal bars have been
fitted properly.
15) ABS SYSTEM – ESC SYSTEM
•The ABS gets the most from the available grip, but it cannot
improve it; you should therefore take every care when driving on
slippery surfaces and not take unnecessary risks.
•When the ABS cuts in and you feel the brake pedal pulsating,
do not remove your foot, but keep the pedal pushed down; in
doing so you, will stop in the shortest distance possible under
the road conditions at the time.
•If the ABS system intervenes, this indicates that the traction of
the tyres on the road is nearing its limit. You must slow down to
a speed compatible with the available traction.
• To obtain the maximum efficiency of the braking system, a
bedding-in period of about 500 km is needed: during this period
it is better to avoid sharp, repeated and prolonged braking. • The ABS, ESC and ASR systems cannot overrule the natural
laws of physics, and cannot increase the grip available according
to the condition of the road.
• The ABS, ESC, ASR and HBA systems cannot prevent
accidents, including those due to excessive speed on corners,
driving on low-grip surfaces or aquaplaning.
• The capability of the ABS, ESC, ASR and HBA systems must
never be tested irresponsibly and dangerously, in such a way as
to compromise personal safety and the safety of others.
•When the Mechanical Brake Assist intervenes, noises may be
heard from the system.
This is normal. In any case, while braking keep the brake pedal
firmly depressed.
•If only the
xwarning light on the instrument panel lights up
(together with a message in the multifunction display, for
versions/markets, where provided) stop the vehicle immediately
and contact the nearest Fiat Dealership. Fluid leaking from the
hydraulic system will compromise the operation of the braking
system, whether it is of the conventional type or with ABS.
•Do not take unnecessary risks, even if your vehicle is fitted with
the ESC and ASR systems.
Your driving style must always be suited to the road conditions,
visibility and traffic. The driver is always responsible for road
safety.
•If the space-saver wheel (where provided) is used, the ABS,
ASR and ESC systems keep operating.
Always remember that the space-saver wheel, being smaller than
the original wheel provides less grip.
•For correct operation of the ABS, ESC and ASR systems, the
tyres must absolutely be of the same brand and type on all
wheels, in perfect conditions and, above all, of type, brand and
size specified.

IMPORTANT INFORMATION AND RECOMMENDATIONS
194
Therefore, always deactivate the passenger airbag when a
rearward facing child restraint system is installed on the front
passenger seat.
The front passenger seat must also be positioned
back as far as possible in order to prevent the child restraint
system from coming into contact with the dashboard.
Immediately reactivate the passenger airbag as soon as the
child restraint system has been removed.
Also remember that, if the key is turned to STOP, none of the
safety devices (airbags or pretensioners) will be deployed in
the event of collision. Non-deployment in such cases does not
indicate a system malfunction.
•Do not wash the seats with water or pressurised steam
(wash by hand or at automatic seat washing stations).
• The front airbag is designed to be deployed for impacts of a
greater intensity than for the pretensioners. For impacts whose
intensity falls between the two levels, normally, only the
pretensioners will be activated.
•Do not affix rigid objects to the garment hooks or support
handles.
•The airbag does not replace seat belts but increases their
efficiency. Furthermore, since front airbags are not deployed in
low-speed frontal impacts, side impacts, rear shunts or roll-
overs, the passengers are protected only by the seat belts
which must therefore be fastened at all times.
•In some versions, in case of a LED
“fault (located on the
plate of the instrument panel), the warning light ¬on the
instrument panel turns on and the passenger side airbags are
deactivated. •Malfunction of the
¬warning light is indicated by the activation
of an airbag fault symbol and a dedicated message on the
instrument panel display (or, for versions where provided, by the
activation of a blinking generic fault warning light).
In this case, the warning light
¬may not indicate failures in the
retaining systems. Contact a Fiat Dealership immediately to have
the system checked.
•The
“warning light indicates the passenger side airbag
protection status. If the warning light is off, passenger side
protection is active: to deactivate it, use the Setup Menu (in this
case the LED lights up). When the vehicle is started (ignition key
turned to MAR position), the warning light turns on for about 8
seconds, provided that at least 5 seconds have elapsed from
when it was switched off. If not, contact a Fiat Dealership. If the
engine is switched off/on again in less than 5 seconds the
warning light may remain off. In this case, to check correct
warning light operation, switch the engine off, wait for at least 5
seconds and switch the engine on again. The warning light may
light up with various intensity levels depending on the vehicle
conditions. The intensity may also vary during the same key
cycle.
•When the ignition key is turned to MAR, the
“warning light
switches for few seconds, then if the passenger airbag protection
is active it should switch off.
26) STARTING THE ENGINE
•It is dangerous to run the engine in enclosed areas. The engine
takes in oxygen and releases carbon dioxide, carbon monoxide
and other toxic gases.
(CONTINUES)
PERSONAL SAFETY
(CONTINUED)