2018 FIAT 500 Time

KNOWING YOUR CAR
60
Radio passport
This document certifies ownership of
the system. The vehicle radio passport
shows the system model, serial
number and secret code.
WARNING Keep the vehicle radio
passport in a safe place so that you
can give the information to the relevant
authorities if the system is stolen.
In case of loss of the car radio
passport, contact the Fiat Dealership,
taking an ID document and the car
ownership documents.Important notes
In the event of a failure, the system
should only be checked and repaired at
a Fiat Dealership.
If the temperature is particularly low,
the display may take a while to reach
optimum brightness.
If the vehicle is stopped for a while and
the external temperature is very high,
the system may go into “thermal
protection” mode, suspending
operation until the temperature in the
passenger compartment returns to
acceptable levels.
Look at the screen only and when it is
necessary and safe.
If you need to look at the screen for a
long time, pull over to a safe place so
as not to be distracted while driving.
Immediately stop using the system in
the event of a fault. Otherwise the
system might be damaged. Contact a
Fiat Dealership as soon as possible to
have the system repaired.
USB SOURCE
To activate USB mode, insert an
appropriate device into the vehicle USB
port (fig. 61).
IMPORTANT After using a USB
recharging socket, we recommend
always disconnecting the device
(smartphone) by removing the cable
from the vehicle socket first, never
from the device (fig. 61).
Cables left flying or connected
incorrectly could compromise correct
recharging and/or the USB socket
condition.
61DVDF0S0188c

65
Switching the
system on/off
The system is switched on/off by
pressing the gbutton/knob.
Turn the button/knob clockwise to
increase the radio volume or
anticlockwise to decrease it.
Radio (tuner) mode
The system is equipped with the
following tuners: AM, FM.
Radio mode selection
Press the RADIO button on the
front panel to activate radio mode.
Selecting a frequency band
The different tuning modes can be
selected by pressing the RADIO button
on the front panel.
Indications on display
After the desired radio station is
selected on the display, the following
information is shown (INFO mode
activated):In the upper part:
the preset station, the time and the
other active radio settings are
highlighted (e.g.: TA).
In the central part:
the name of the current station, the
frequency and the radio text
information (if any) are highlighted.
FM station list
Press the BROWSE ENTER
button/knob to display the complete list
of the FM stations that can be
received.
AM/FM radio
station storage
The preset stations are available in all
system modes and are selected by
touching one of the presetting buttons
1-2-3-4-5-6 on the front panel.
If you are tuned to a radio station that
you wish to store, hold down the
button on the display which
corresponds to the desired preset until
an acoustic confirmation signal is
emitted.AM/FM radio station selection
To search for the desired radio station
press the
”or »button or use the wheel of
the steering wheel controls
NO, or
turn the “BROWSE ENTER” knob.
Searching for the
previous/next radio station
Press briefly the
”or »button or
use the wheel of the steering wheel
controls
NO: when the button is
released the previous or next radio
station is displayed.
Previous/next radio
station fast search
Hold down the
”or »button to
start the fast search: when the button
is released, the first tunable radio is
played.

67
Settings
Press the MENU button on the front
panel to display the “Settings” menu.
NOTE The menu items displayed can
vary according to the versions.
The menu includes the following items:
❒ System Settings: Language,
Reset Default Value, System Power
Off, Power on Volume Limit, Auto-
On Radio.
❒ Radio Menu: Browse FM Station
List, Traffic Announcements,
Regional, Alternative Frequency.
❒ Radio Off Delay:
permits the system to be kept on
for a preset time after the ignition
key is turned to STOP.
Audio mode
To access the “Audio” settings menu
briefly press the AUDIO button on the
front panel.
The menu includes the following items:
❒ TREBLE: adjustment of treble
tones;
❒ MID: adjustment of mid tones;
❒ BASS: adjustment of bass tones;
❒ BALANCE: balancing of left/right
speakers;
❒ SVC: speed adjustment according
to vehicle speed;
❒ LOUDNESS: audio improvement at
low volume;
❒ AUX OFFSET: radio on or off when
the vehicle is started.
❒ AUX OFFSET (where provided):
This lets you align the portable
device volume to that of the other
sources.

77
Connected services that can be
accessed on the vehicle
The Uconnect™ LIVE services
available in the radio menu can change
according to the market.
The eco:Drive™ and my:Car
applications were developed to
improve the customer’s driving
experience, therefore they are available
in all markets, where the Uconnect™
LIVE services can be accessed.
For further information visit the
www.DriveUconnect.eu website.
If the navigation system is installed in
the radio, accessing the Uconnect™
LIVE services enables use of the
TomTom LIVE services. Further
information about the LIVE functions is
available in the dedicated chapter.
eco:Drive™
The eco:Drive™ application allows you
to display your driving behaviour in real
time, in order to help you reach a more
efficient driving style as far as
consumption and emissions are
concerned.In addition, the data can be saved on a
USB flash drive, and the data analysis
can be made on your personal
computer thanks to the eco:Drive™
desktop application, available on
www.fiat.it or www.DriveUconnect.eu.
Driving style is evaluated by means of
four indices which monitor the
following parameters:
❒ Acceleration
❒ Deceleration
❒ Shifting
❒ Speed
eco:Drive™ display
Press the eco:Drive™ button to
interact with the function.
A screen will be displayed on the radio,
showing the 4 indices described
above. These indices are grey until the
system has enough data to evaluate
the driving style.
Once sufficient data are available, the
indices will have 5 colours depending
on the evaluation: dark green (very
good), light green, yellow, orange and
red (very bad).“Current trip index” refers to the entire
value calculated in real time based on
the average of the described indices.
It represents eco-friendliness of the
driving style: from 0 (low) to 100 (high).
In the event of extended inactivity the
display will show the average of the
indices up to that moment (”Average
index”) then the indices will be
coloured again in real time as soon as
the vehicle is restarted.
To check the data average of previous
trip (a “trip” is a cycle starting from
when the ignition key is turned on until
it is turned off), select the “Previous
Trip” button (fig. 4).
The details of the previous trip can also
be displayed by pressing the “Details”
button, in which duration (time and
mileage) and average speed will be
shown.

KNOWING YOUR CAR
78
Recording and transferring
trip data
The trip data can be stored in the
system memory and transferred using
a suitably configured USB memory
stick or by Uconnect™ LIVE app.
This allows you to display the history of
the collected data, showing the
complete analysis of the trip data and
of your driving style.
Further information is available at
www.driveuconnect.eu.
IMPORTANT Do not remove the USB
memory stick nor unpair the
smartphone and the Uconnect™ LIVE
App before the system has
downloaded the data, otherwise it
could be lost.
During the transfer of data to the
devices, messages may appear on the
radio display to guide the user
correctly through the operation; follow
these instructions. These messages
are only displayed with the ignition key
at STOP and when a delay in the
system switching off is set.
The data are automatically transferred
to the devices when the engine is
switched off. Transferred data will be
deleted from the system memory in
this manner. You can choose to store the trip data
or not, by pressing the “Settings”
button and by setting the storage
activation and the USB or Cloud
transfer mode.
REMARKS
When the USB memory stick is full, the
warning messages are shown on the
radio display.
When the eco:Drive™ data are not
transferred to USB memory stick for a
long time, the internal memory of the
Uconnect™ LIVE system may be
exhausted. Follow the instructions
given by the messages on the radio
display.
my:Car
my:Car allows you to keep the “health”
of your vehicle always under control.
my:Car can detect malfunction in real
time and inform the user about the
expiry of the servicing interval. Press
the “my:Car” button to interact with the
application.
The display will show a screen with the
“care:Index” section, which provides all
the detailed information about the
status of the vehicle. Press the “Active
warnings” button (if present) to showthe details of the vehicle’s faults which
caused a warning light to switch on.
The vehicle status can be seen both
on www.driveuconnect.eu or through
the Uconnect™ LIVE app.
Settings
Press the button on the front
panel to display the main “Settings”
menu.
NOTE The menu items displayed vary
according to the versions.
Indicatively, the menu is composed of
the following items:
❒ Display;
❒ Units;
❒ Voice commands;
❒ Clock & Date;
❒ Safety;
❒ Lights (for versions/markets, where
provided);
❒ Doors & Locks;
❒ Vehicle Off Options;
❒ Audio;
❒ Phone/ Bluetooth;

KNOWING YOUR CAR
80
❒ The USB device must use a FAT-32
file system.
❒ The USB device must not be locked
and it must be possible to save files
on it.
NOTE It is advisable to use a memory
stick, while the use of mass storage
devices, such as mobile phones or
multimedia players, is not
recommended.
To prepare a USB device, proceed as
follows:
❒ Select “Navigation updates” in the
“Settings” menu.
You are asked whether you wish to
prepare a USB device for downloading
updates.
❒ Select "Yes".
❒ Insert the USB device.
NOTE If the system continues to ask
you to insert the USB device, check
that the device meets the requirements
indicated previously, then retry.
The system starts to prepare the USB
device.
When the USB device is ready, the
following message is displayed.Remove the USB device and connect it
to the computer.
The new map can now be downloaded
to the USB device.
TomTom HOME installation
To install TomTom HOME and create a
MyTomTom account, proceed as
follows:
❒ Download and install the TomTom
HOME application on the computer.
On the computer, access
tomtom.com/getstarted. Select
“Download TomTom HOME”, then
follow the instructions provided.
❒ Connect the USB device prepared
using the computer. TomTom
HOME is started automatically.
❒ Select “Log in” in the top right
corner of TomTom HOME.
❒ Select “Create account” and enter
the required details to create a
MyTomTom account. A MyTomTom
account is required to receive map
updates.After the account is created, you are
asked whether you wish to connect the
Uconnect™ system to your account.
The USB device prepared represents
your Uconnect™ system.
❒ Select “Link device”, then select
“Close”.
A map can now be downloaded to the
USB device.
Downloading a map
Connect the USB device to the
computer.
If a map update is available for the
system, this update is included in the
list of updates available.
NOTE If the most recent map is already
installed on the system, the update is
not proposed.
Select the map that you wish to
download, then select
“Update and install”.
The map is downloaded and copied to
your USB device.
Select “Done” when the process is
complete.

89
In the upper part: information on the
track being played and the following
graphic buttons:
❒ “Repeat”: to repeat the track being
played;
❒ “Shuffle”: to play the tracks in
random order.
In the middle: information on the
track being played.
On the left: display of the following
buttons:
❒ Selected device or audio source;
❒ “Select source”: select the required
audio source.
On the right: display of the following
buttons:
❒ “Info”: additional information on the
track being played;
❒ “Tracks”: list of available tracks.
❒ “Map”: navigation map view
(Uconnect™7” HD Nav LIVE
versions only).At the bottom: information on the
track being played and the following
graphic buttons:
Active device or audio source;
❒
÷/ ˜: select previous/next
track;
❒
II: pause track being played;
❒ “Audio”: access to the “Audio
Settings” screen.
Track selection (Browse)
The “Tracks” function allows you to
open a window with the list of tracks
being played.
The choices available depend on the
device connected.
For example, on a USB device, you
can also use the SCROLL TUNE
button/knob to browse the list of
artists, genres and albums available on
the device, depending on the
information available on the tracks.
NOTE This button may be disabled for
some Apple®devices.
Turn the SCROLL TUNE button/knob
to select the desired category and then
press it to confirm the selection.NOTE The "Tracks" button does not
allow any operation on the AUX device
(where provided).
NOTE The indexing time of a USB
device can vary according to the
media inserted (in some cases it can
take a few minutes).
Bluetooth® SOURCE
This mode is activated by pairing a
Bluetooth® device containing music
tracks with the system.
PAIRING A Bluetooth®
AUDIO DEVICE
To pair a Bluetooth®audio device,
proceed as follows:
❒ activate the Bluetooth®function
on the device;
❒ press the “Media” button on the
display;
❒ press the “Select Source” button;
❒ select the Bluetooth® Media
source;
❒ press the “Add Device” graphic
button;

93
SIRI EYES FREE
(available with iPhone 4S and higher
and compatible iOS only)
After having paired the Siri enabled
device to Uconnect™ hold the
}button
on the steering wheel pressed and then
release it.
After the double beep, you can start
interacting with Siri, to listen to music,
make calls, read text messages and
more.
Uconnect™ LIVE
SERVICES
Press the Uconnect™ button to
access the Uconnect™ LIVEapps.
The services available depend on the
car configuration and the market.
To use the Uconnect™ LIVE
services, you need to download the
Uconnect™ LIVEapp from Google
Play or Apple Store and register using
the app or on www.DriveUconnect.eu.
First access to the vehicle
Once you have launched the
Uconnect™ LIVEapp and entered
your details, you have to pair the
Bluetooth® with your smartphone and
the radio, as described in the “Pairing
a mobile phone” chapter, to access
the Uconnect™ LIVEservices in your
vehicle.When pairing is complete, the
connected services can be accessed
by pressing the Uconnect™ LIVE
icon on the radio.
Before you can use the connected
services, you must first do the
Bluetooth®pairing, then complete
the activation procedure by following
the instructions that appear in the
Uconnect™ LIVEapp.
Setting of Uconnect™ LIVE
services that can be managed
through the radio
In the Uconnect™ LIVEradio menu
the “Settings” section can be accessed
by pressing the icon . In this
section the user can check the system
options and change them according to
their preferences.
System updates
If an update for the Uconnect™ LIVE
system is available while the
Uconnect™ LIVEservices are being
used, you will be informed with a
message on the radio screen.
Connected services that can be
accessed on the vehicle
The eco:Drive™ and my:Car
applications were developed to
improve the customer’s driving
experience, therefore they are available
in all markets, where the Uconnect™
LIVEservices can be accessed.
If the navigation system is installed in
the radio, accessing the Uconnect™
LIVE services enables use of the
“Live” services.
eco:Drive™
The eco:Drive™ application allows you
to display your driving behaviour in real
time, in order to help you reach a more
efficient driving style as far as
consumption and emissions are
concerned.
In addition, the data can be saved on a
USB flash drive, and the data analysis
can be made on your personal
computer thanks to the eco:Drive™
desktop application, available on
www.DriveUconnect.eu.
Driving style is evaluated by means of
four indices which monitor the
following parameters: acceleration,
deceleration, gearchange, speed.