2018 BMW 4 SERIES COUPE Owners Manual

Forward/backward
Pull the lever and slide the seat in the desireddirection.
After releasing the lever, move the seat forj
ward or back slightly making sure it engages
properly.
Height
Pull the lever and apply your weight to the seat or lift it off, as necessary.
Backrest
tilt
Pull the lever and apply your weight to the
backrest or lift it off, as necessary.
Seat
tilt
Pull the lever and move the seat to the desired
tilt. After releasing the lever, apply your weight to the seat or lift it off to make sure the seat
engages properly.
Electrically
adjustable
seats
General
information
The seat setting for the driver's seat is stored
for the profile currently used. When the vehicle
is unlocked via the remote control, the position
is automatically retrieved if the function, refer to page 58, is activated for this purpose.
The current seat position can be stored using
the memory function, refer to page 71.
Overview
1Memory function2Backrest width3Lumbar support4Backrest tilt5Forward/backward, height, seat tiltSeite 65SettingsControls65
Online Edition for Part no. 01402978133 - II/17

Forward/backward
Push switch forward or backward.
Height
Push switch up or down. Seat
tilt
Move switch up or down.
Backrest
tilt
Move switch forward or backward.Thigh
support
Pull the lever at the front of the seat and adjustthe thigh support.
Lumbar
support The curvature of the seat backrest can be adj
justed in a way that it supports the lumbar rej gion of the spine. The lower back and thespine are supported for upright posture.
'yPress the front/rear section
of the button:
The curvature is increased/
decreased.'yPress the upper/lower secj
tion of the button:
The curvature is shifted up/ down.Seite 66ControlsSettings66
Online Edition for Part no. 01402978133 - II/17

Backrest
width
General
information
You can change the backrest width by adjustj
ing the side wings of the backrest.
Settings'yPress the front section of
the button:
The backrest width dej
creases.'yPress the rear section of the
button:
The backrest width inj
creases.
Front
seat
heating
Overview
Seat heating
Switching
on Press button once for each temperajture level.
The maximum temperature is reached when three LEDs are lit.
If the trip is continued within approx. 15 mij
nutes after a stop, seat heating is activated auj
tomatically with the temperature selected last.
When ECO PRO is activated, the heater output
is reduced.
Switching
off
Press and hold the button, until the
LEDs go out.
Entering
the
rear
Safety
information WARNING
There is a risk of jamming when moving
the seats. There is a risk of injury or risk of
property damage. Make sure that the area of movement of the seat is clear prior to any adjjustment.'

Original
position1.Push the seat back into the original posij
tion.2.Fold back the backrest to lock the seat.
Electric
forward/backward
adjustment
Comfort
entry
The comfort entry contains a memory function for forward/backward and backrest adjustjment.
1.Pull lever up to the stop.2.Fold backrest forward.3.To change the entry area:'yPress and hold this button untilthe seat has moved to the dej
sired position. Releasing the button
stops window/roof movement.'yPress button briefly. The seat auj
tomatically moves to the end poj
sition. Pressing again stops the motion.
Original
position
1.Moving the seat to its original position:'yPress and hold this button until the seat has moved to its original
position. Releasing the button stops window/roof movement.'yPress button briefly. The seat
moves to its original position.
Pressing again stops the motion.2.Fold the backrest back.Safety
belts
Number
of
safety
belts
and
safety
belt
buckles
The vehicle is fitted with four safety belts to
ensure occupant safety. However, they can
only offer protection when adjusted correctly.
General
information
Always make sure that safety belts are being
worn by all occupants before driving off. Alj
though airbags enhance safety by providing added protection, they are not a substitute forsafety belts.
The upper shoulder strap's anchorage point will be correct for adult seat occupants of evj ery build if the seat is correctly adjusted.
Safety
information WARNING
If the safety belt is used to buckle more
than one person, the protective effect of the safety belt can no longer be ensured. There is
a risk of injuries or danger to life. Do not allow more than one person to wear a single safety
belt. Infants and children are not allowed on an occupant's lap, but must be transported andsecured in designated child restraint sysj
tems.'

'yThe safety belts or safety belt buckles aredamaged, soiled, or changed in any other
way.'yBelt tensioners or belt retractors were modified.
Safety belts can be imperceptibly damaged inthe event of an accident. There is a risk of injuj
ries or danger to life. Do not modify safety
belts, safety belt buckles, belt tensioners, belt
retractors or belt anchors and keep them
clean. Have the safety belts checked after an
accident at the dealerss service center or anj other qualified service center or repair shop.'

'yWaiting time approx. five minutes.'yOpening the respective door.'yAfter a short trip.'yLocking the vehicle.
If the respective door is closed, the belt carrier
is re-activated when the vehicle key has been
detected in the interior.
Pinch
protection
system WARNING
When extending and retracting the belt
carrier, body parts and objects can be jammed. There is a risk of injury or risk of property damj
age. Make sure that the area of movement of the belt carrier is clear.'

'yForward: pull the top edge of the head rej
straint forward, arrow 1.'yBack: press the button,arrow. 2. The head restraint folds as far back as possible.
Removing
Only remove the head restraint if no one will besitting in the seat in question.
1.Raise the head restraint up against the rej
sistance.2.Press the button, arrow 1, and pull the head restraint out completely.
Memory
function
Concept
The following settings can be stored and, if necessary, retrieved using the memory funcj tion:
'ySeat position.'yExterior mirror position.'yHeight of the Head-up Display.General
information
Two memory locations with different settings can be set for each driver profile, refer to
page 54.
Depending on the vehicle equipment, the folj
lowing settings are not stored:'yBackrest width.'yLumbar support.
Safety
information
WARNING
Using the memory function while driving
can lead to unexpected movements of the
seat. Vehicle control could be lost. There is a
risk of an accident. Only retrieve the memory function when the vehicle is stationary.'

Button was pressed inadvertently:
Press button again.
The LED goes out.
Calling
up
settings
The stored position is called up automatically.
Press selected button 1 or 2.
The procedure stops when a switch for setting
the seat or one of the memory buttons is pressed.
While driving, the seat position adjustment on the driver's side is interrupted after a short
time.
Calling
up
of
a
seat
position
deactivated
After a brief period, calling up stored seat posij tions is deactivated to save battery power.
To reactivate calling up of a seat position:'yOpen and close the door or tailgate.'yPress a button on the remote control.'yPress the Start/Stop button.
Mirrors
Exterior
mirrors
General
information The mirror on the front passenger side is more
curved than the driver's side mirror.
The mirror setting is stored for the driver proj
file currently in use. When the vehicle is unj
locked via the remote control, the position is
automatically retrieved if the function, refer to page 58, is activated for this purpose.
The current exterior mirror position can be stored using the memory function, refer to
page 71.
Safety
information
WARNING
Objects reflected in the mirror are closer
than they appear. The distance to the traffic
behind could be incorrectly estimated, for inj stance while changing lanes. There is a risk of
an accident. Estimate the distance to the traffic behind by looking over your shoulder.'