2018 AUDI S3 SEDAN wheel

Emergency assistance
-Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack.
-Always store the veh icle tool kit , the jac k
and the replaced tire in the luggage com­ partment
c:> page 255.
(D Tips
Obey all laws.
Changing a wheel
When you change a wheel, follow the sequence
described below step -by-step and in exactly that
order .
1. Remove the decorative wheel cover*. For
more details see also
c:> page 364, Decor a­
tive wheel covers
or c:> page 365, Wheels
with wheel bolt caps.
2 . Loosen the wheel bolts c:> page 365 .
3. Locate the proper mounting point for the
jack and align the jack below tha t point
c:> page 366 .
4. Raise the car w ith the jac k c:> page 366 .
5. Remove t he wheel with the flat tire an d t hen
ins tall
the spare c:> page 367.
6. Tighten all wheel bolts light ly .
7.
Lower the veh icle w ith the jack .
8. Use t he wheel bo lt wrench and
firmly t ighten
all whee l bolts
c:> page 365 .
9. Replace the decorative wheel cover* .
A WARNING
Always read and fo llow all WARNI NGS and in­
forma tion
c:> .& in Raising the vehicle on
pag e 366
an d c:> pag e 368 .
After changing a wheel
A wheel change is not complete without the do­
ing the following .
.,. Always store the vehicle tool kit, the jack * and
the replaced t ire in the luggage compartment
c:> pag e 255 .
.,. Check the tire pressure on the spare wheel im­
m ed iate ly aft er mo unt ing it.
364
.,. As soon as possib le, h ave the tightening tor­
ques
on a ll wheel bolts checked with a torq ue
w rench . The correct tighteni ng torq ue is
90 ft lb (120 Nm).
.,. Have the flat t ire replaced as soon as poss ib le .
(D Tips
-If you not ice that the wheel bo lts are cor­
roded and d ifficult to turn while c hanging a
t ire , th ey s hou ld be replaced before you
check the t igh tening torque.
-Dr ive at reduced speed until yo u have the
t igh tening torques checked .
- After chang ing a wheel, the tire p ressure in
all four tires must be checked/cor rected and
t h e tire pressure monito ring ind icator must
be stored in th e
MMI r:::;, pag e 349 .
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 285 Chang ing a whee l: Remov ing t he wh eel cover
Removing
.,. In sert t he hook (p rov ided w ith the vehicle t ool
kit ) in t he hole in the w heel hu b cover.
.,. Pull off the decorative wheel cover c:> fig . 285 .

LL co .... N
" N .... 0 N > co
Wheels with wheel bolt caps
Applies to: ve hicles wit h whee l bo lts w ith ca ps
The cops must be removed first from the wheel
bolts before the bolts con be unscrewed.
Fi g. 286 Changing a wheel: removing the whee l bo lt caps
Removing
.,. Push the pla stic clip (provided wi th the veh icle
tool kit) over the wheel bolt cap unti l the inner
retainers on the clip align with the edge of the
cover.
.,. Remove the cap with the pla stic cli p (vehicle
tool kit)
¢ fig . 286.
Refitting
.,. Place the caps ove r the wheel bo lts and push
them back on.
The caps are to protect and keep the whee l bolts
clean.
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising
the vehicle.
F ig. 287 C hanging a wheel: loosening the wheel bo lts
Em ergen cy as sis tanc e
Loosen ing
.,. Slide t he whe el wren ch onto the wheel bo lt as
fa r as it will go.
.,. Take tight hold of the end of the wrench hand le
and turn the wheel bolts
counter-clockwise
about one single turn in the direction of arrow
¢fig. 287.
Tightening
.,. Slide the wheel wrench onto the wheel bo lt as
far as it will go .
.,. Take tight hold of the end of the wrench hand le
and turn each wheel bolt
clo ckw ise until it is
seated.
A WARNING
-- Do not use force or hurry when changi ng a
wheel
-you can cause the vehicle to slip off
the jack and cause ser ious persona l inju ries .
-Do not loosen the wheel bolts more than
on e turn
befo re you raise the veh icle with
the jack.
-Y ou r is k an injury.
(D Tips
- Never use the hexagonal socket in the han­
dle of the screwdr iver to loosen or tighten
the whee l bolts.
- If a wheel bo lt is very tight, yo u may find it
easier to loosen by ca refully pushing dow n
on the e nd of the whee l bolt w rench with
one foot only. As you do so, hold on to the
car to keep yo ur balance and take care not
to slip.
365

Emergency assistance
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel can be removed.
Fig. 288 Sill panels : mark in gs (exa mple)
Fig. 289 Sill : positio nin g th e ve hicle jack
,.. Engage the parking brake to prevent your vehi­
cle from rolling unintentionally.
,.. Move the selector lever to position P.
,.. Find the marking (imprint) on the sill that is
nearest the wheel that will be changed
c> fig . 288 . Behind the marking, there is a lift­
ing point on the sill for the vehicle jack.
,.. Vehicles with a sill: Note the position of the sill
when positioning the vehicle jack
c::> fig. 289.
,.. Place the vehicle jack (vehicle tool kit) on a firm
surface. Use a flat, stable support if necessary.
On a slippery surface such as tile, you should
use a non-slip pad (such as a rubber mat)
c::> ,&..
,.. Turn the vehicle jack located under the lifting
point on the sill to raise the jack until its arm @
c> fig. 289 is located under the designated plas­
tic mount
c::> ,& , c::>G) .
,.. Align the jack so that its arm@ c::> fig. 289 en­
gages in the designated lifting point in the door
sill and the movable base @ lies flat on the
ground. The base @ must be
vertical under the
lifting point @.
366
,.. Wind the jack up further until the flat tire
comes off the ground
c::> ,&. .
Position the vehicle jack only under the designat­
ed lifting points on the sill
c::>fig. 288. There is ex­
actly
one location for each wheel. The jack must
not be positioned at any other location
c::> & c::>(I) .
An unstable surface under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground. If necessary
place a sturdy board or similar support under the
jack. On
hard, slippery surfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c::> & .
A WARNING -
-You or your passengers could be injured
while changing a wheel if you do not follow
these safety precautions :
-Position the vehicle jack only at the desig­
nated lifting points and align the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle .
-A soft or unstable surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the ground . If necessary, use a sturdy
board under the jack.
-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
-Only raise your vehicle with the vehicle
jack provided by the factory. If you use a
vehicle jack for another vehicle, your vehi­
cle can slide and cause injury.
-Changes in load can affect the height of
the vehicle.
-Never start the engine when the vehicle is
raised, which could cause an accident.
-Support the vehicle securely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potential risk for injury .
-To help prevent injury to yourself and your
passengers:

LL co .... N
" N .... 0 N > co
-Do not raise the v ehicl e until you are sure
the jack is securely engaged .
- Passengers must not rema in in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
p lace away from the vehicle and well away
from the road and traff ic.
- Make sure jack position is correct, adjust
as necessary and then cont inue to raise
the jack.
CD Note
Do not li ft the vehicle by the sill. Position the
vehicle jack on ly at the designated lifting
points on the sil l. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing the spare
Follow th ese instructions st ep-by-step for chang­
ing the wheel .
Fig . 2 90 Ch angin g a w hee l: u sin g th e screwdr ive r ha ndle
(with t he bla de remo ved} t o turn t he bolts
F ig. 291 C h anging a w hee l: ali gnm en t pi n in side the to p
h ol e
1l Appli es to veh icles with ceram ic br ake rot ors•: Use a sec ­
on d alig nme nt pin * (sto re d in t he s pare w hee l we ll mo ld­
ing} for the lo w er hole , fo ll o w ing the de scr ip tion for t he
firs t alig nmen t pin .
Em ergen cy as sis tanc e
After you have loosened all whe el bo lts and
raised the vehicle off the gro und, remove and re­
place the wheel as follows:
Removing the wheel
.,. Use the hexagonal socket in the screwdriver
handle
t o comp letely remove the topmost
wheel bo lt and set i t aside on a
clean su rface
r=> fig. 290.
.,. Screw the threaded end of the alignment pin
from the too l kit hand-tight into the empty bo lt
hole
c> fig . 2911>.
.,. Then remove the other wheel bolts as descr ibed
above .
.,. Take off the whee l leaving the alignment p in in
the bolt hole
~ 0-
Putting on the comp act spare wheel
.,. Lift the spare wheel and carefully slide it over
the alignment p in to guide it in
place r=>@.
.,. Use the hexagonal socket in the screwdr iver
ha ndle to screw in and t igh ten all wheel bolts
slightly .
.,. Remove the alignmen t pin and insert and t igh t­
en the remaining wheel bo lt s light ly like the
rest .
.,. Tu rn the jack hand le counter-clockwise to lowe r
the vehicle until the jack is fully released .
.,. Use the wheel bolt wrench to tighten a ll wheel
bolts firmly
c> page 365 . Tighten them cross­
wise,
from one bo lt to the (approx imately) op ­
posite one , to keep the wheel centered .
CD Note
When removing or installing the wheel , the
r im could h it the brake rotor and damage the
r otor. Work carefully and have a second per­
son help you.
@ Tips
Never use the hexagonal socket in the handle
of the sc rewdrive r to loosen or t ighten the
whee l bolts.
367

Emergency assistance
-Pull th e revers ible blade from the sc rew driv ­
e r before you use the he xag onal socket in
the handle t o turn the w heel bo lts .
- W hen mounting ti res w ith
unidirectional
tread design
make sure the t read pattern is
po inted the r igh t way
c> page 36 8.
-The wheel bolts should be clea n and easy to
turn . C heck for di rt and c orros io n on t he
mating surfaces o f both the wheel an d the
hu b. Remove all dirt from t hese surfaces be­
fo re r emo untin g the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mount ed with th eir tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
W hen using a spare ti re with a tread patte rn in­
tended fo r use in a spec ific d ir e ction, please note
t he following:
- The direct ion of rotat io n is marked by an a rrow
o n the side of the tire.
- If the spare tire has to be installed in the incor­
r ect d irection, use the spare tire only tempora­
r ily s ince the t ire w ill not be ab le to achieve its
o pti mum p erf ormance c harac ter istics wi th re­
gard to a quaplaning, noise and wea r.
- We recommen d that you pay particular atten ­
t ion to this fac t during wet weathe r and that
yo u adju st yo ur spe ed to match roa d condi­
tio ns.
- Replace t he flat t ire with a new one and have i t
in stall ed on yo ur vehicle as soon as possible to
r e stor e th e han dling adv antage s of a un id ir e c­
ti on al ti re.
Notes on wheel changing
Please read the info rmation c> page 33 7 if you
are going to use a spare tire which is different
from the tires on yo ur vehicle .
Afte r you change a tire:
-Check the tire pressure on the spare immedi­
ately after installation.
368
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lbs (120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque .
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
A WARNING
- If you are goi ng t o equip yo ur vehicle with
t ires or r ims which diffe r from those which
wer e fac to ry install ed, th en be su re to read
t he infor matio n
c> pag e 33 7.
- Always mak e sure th e damag ed wheel or
e ve n a fl at tire and th e jack and to ol kit ar e
pr op erl y se cure d in t he l uggage com part­
me nt a nd are no t loos e in the pass eng er
c omp artment.
- In a n ac cide nt or sudde n maneuver they
co uld fly forw ard, i njuring a nyon e in the ve­
h icle.
- Alway s store damage d wheel, j ack a nd too ls
secure ly in the lu g gage compa rt ment. O th­
erwise, in an a cci den t or sudden maneuve r
they cou ld fly forwar d, cau sing injury to pas­
sen gers in the veh icle.
-

LL co ..... N
" N ..... 0 N > co
Spare tire
General information
Applies to: vehicles with space-saving spare tire (compact
spare tire)
Fig. 292 Luggage co mpa rtment: cargo floo r fo lded up
(versio ns 1 and 2 )
F ig. 293 Spare tire (exa mple)
The spare tire ~ fig. 293 is intended for short­
term use only . Have the damaged tire checked
and replaced if necessary by an authorized Audi
dealer or authori zed Audi Service Facility as soon
as possible.
There are some restrictions on the use of the
compact spare tire . The compact spare tire has
been designed specifically for your type of vehi­
cle . Do not replace it with the spare tire from an­
other type of vehicle.
Emergency assistance
" Lift the cargo floor by the p lastic handle.
" Hang the p lastic hook on the luggage compart ­
ment sea l
(D ~ fig. 292 .
"Turn the handwheel counter-clockwise and re-
move it .
"Remove the spare tire .
Snow chains
For technical reasons, the use of snow chains on
the compact spare tire is not permitted.
If you have to drive wi th snow chains and a front
tire fails, mount the spare tire in place of a rear
tire. Install the snow chains on the rear tire that
you removed, and install that in place of the
front t ire th at failed.
A WARNING
--
- After installing a spare tire, the t ire pres­
sure must be checked as soon as possible.
The tire pressure is available on
~ page 341,
fig . 278
- Do not drive faste r than SO mph (80 km/h)
with a compact spare t ire. Driving faster
than that increases the risk of an accident.
- To reduce the r isk of an accident, avoid full­
throttle accelerat ion, heavy braking, and
fast cornering with the compact spare tire.
- To reduce the r isk of an accident, neve r drive
with more than one compact spare tire.
- Normal summer or winter t ires must not be
mounted on the compact spare wheel rim .
Removing the subwoofer (version 1)
Applies to: vehicles with subwoofer in the spare wheel well
The subwoofer mus t be removed before the
spare wheel* can be removed .
Fig. 294 Spare tire well: subwoofe r
369

Emergency assistance
Removing the subwoofer
• Lift up the cargo floor ¢ page 369, fig. 292 .
• Press the connector tabs @¢ fig. 294 togeth ­
er.
• Remove the connector @and set the discon-
nected cab le aside.
• Remove the bo lt @ .
• Carefu lly remove t he subwoofer .
Installing the subwoofe r
• Carefully place the subwoofer in the rim we ll.
The word
"FRONT" on the subwoofer must face
f orward.
• Inse rt the connector that was removed .
• Secure the subwoofer with the bolt .
• Fold the cargo floo r cover bac k into p lace.
(D Tips
The subwoofer can also be mounted w hen t he
spare tire is not in the spare wheel well.
Removing the subwoofer (version 2)
Applies to: vehicles w ith s ubwoofer in the spare wheel well
The subwoofer must be removed before the
spare wheel* can be removed .
Fig . 295 Spare t ire well : su bwoofer
Remov ing the subwoofer
• Lift up the cargo floor ¢ page 369 , fig . 292 .
• Pull the lock (D ¢ fig. 295 toward the cab le.
• Press t he lock ing tab @down.
• Remove the connector @and set the removed
cable aside .
• Remove the bolt @.
• Caref ull y remove t he subwoofer.
370
Installing the subwoofer
• C arefully p lace the s ubwoofer i n the r im well.
The word "F RONT" on the s ubwoofer m ust face
forward .
• Insert the connecto r that was removed .
• Slide the lock (D back in the direction of the
subwoofe r.
• Secure the subwoo fer wit h the bolt.
• Fold the cargo floor cover back into place .
(D Tips
The subwoofer can also be mounted when the
spare t ire is not in the spa re whee l wel l.

Fuses and bulbs
Fuse ass ignment - interior
ij
::, CX) ID
F ig. 298 Vehicle interior: fuse assignment
No. Equipment
Fl Ad Blue engine components
F2 Seat adjustment
F3 Power top hydraulic pump
F4 Infotainment control panel,
Infotainment
components
FS Gateway
F6 Selector lever (automat ic transm iss ion)
Air conditioning/heating controls, auxiliary
F7 heating, rear window defogger relay, tire pressure monitor
Electromechan ical park ing brake switch,
light switch, rain/light sensor, anti-theft
F8 alarm system,
diagnostic connector, roof
module, emergency call system, head light
range control
F9 Steering col umn sw itch module
FlO Infotainment system display
Fll Left vehicle electrica
l system control mod-
ule
F12 Infotainment components
F13 Driver's side safety belt tensioner
F 14 Heat ing/a ir condit ion ing system blower
372
No . Equipment
FlS Electronic
steering column lock
F16 Infotainment components
Fl7 Instrument cluster
Fl8 Rearview camera
Fl9 Convenience access control module
F20 Engine components
F21 Steering column, steering wheel heating
switch module
F23 Panorama glass
roof/power top control
module, power top latch
F24 R
ight vehicle electrical system control
module
F2S Driver
's side front/rear power windows
F26 Seat heating
F27 Interior
lights
F28 Power top control module
F29 Interior lights
F30 Diagnostic connector
F32 Front camera, parking
system, ACC sensor,
lane change assist
F33 Airbag
Hold assist button, interior sound, revers-
F34 i
ng light sw itch, temperature sensor, neck
heating relay coil and socket relay, power
top operation button
Air quality sensor, automatic dimming
F3S rearview
mirror, diagnostic connector, cen-
ter console power supply
F36 Right
headlight (LED, Matrix LED)
F37 Left headlight (LED, Matrix LED)
F38 High-voltage battery
F39 Passenger
's side front/rear power w in-
dows
F40 Sockets
F41 Passenger's sid e safe ty be lt tens ioner
F42 Central locking area
F43 Sound-amplifier
F44 All wheel drive
F47 Rear window wiper
F48 Outer sound actuator