a co ...... N r--. N ...... 0
0
:E '
Emergency assistance
General information
.. Par k the vehicle as far as poss ible from moving
traff ic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a leve l surface .
It you are on a steep h ill, be especially careful.
.. Set the parking brake .
.. Switch the emergency flashe rs on.
.. Have the passengers exit the veh icle . They
sho uld move to a safe place, for example be
hind a guard rail.
& WARNING
Follow the steps g iven above. This is for your
protection and the for the safety of o ther driv
ers .
Equipment
Vehicle tool kit/tire mobility kit/vehicle
jack
App lies to: veh icles with the vehicle tool kit, tire mobili ty ki t
an d vehicle jac k
The vehicle tool kit, vehicle jack, tire mobility kit
and comp ressor are s to red in the luggage com
pa rtment unde r the cargo floor cove r. Lift the
cargo floor using the handle.
& WARNING
Impro per use of the vehicle jac k can ca use se
rious perso nal injuries.
- Never use the screw drive r hex he ad to
tigh ten whee l bolts, since the bol ts cannot
atta in the necessary tighten ing torque if you
use the hex head, potentially ca using an ac
c ident.
- The factory-supplied jack is i nten ded on ly
for your vehicle model. Under no circ um
stances should it be used to lift heavy
vehicles or other loads; you r isk injuring
yourself.
- Never start the engine whe n the vehicle is
ra ised, which could ca use a n accident.
- Support the veh icle secure ly with appropr i
ate stands if work is to be performed under-
Em ergen cy as sis tanc e
neath the vehicle; otherwise, there is a po
tential risk for injury.
- Never use the jack supplied with your Audi
on another vehicle, particularly on a heavier
one. The jack is only su itable for use on the
veh icle it came with.
(D Tips
The vehicle jack in your vehicle is mainte
nance-free.
Tire mobility kit
Preparation
.. Read a nd follow the important safety precau-
t ions
¢page 357 .
.. Set the park ing brake .
.. Select the "P" selector lever position .
.. Check if a repair with the tire mobility kit is pos
sible
¢ page 357.
Using the tire mobility kit
Fig. 273 Tire: tire damage t hat can not be repaired
T he tire repair is only meant for tempora ry use .
Change the spare tire as soon as possible¢& .
If the t ire is p ierced by an o bject su ch as a nail,
do no t r emove the object from the tire .
T he tire mob ility kit can be used at tempe ratures
as low as -4 °F (-20 °C).
The tire mobility kit may not be used:
- if the tire has cuts or p unctures that are larger
than 0.16 in (4 mm)
(D ¢ fig . 273
-if the rim is damaged @
- if you drove with very low t ire pressure or with-
out air in the tire @ ..,.
357
Emergency assistance
See an authorized Audi dealer or authorized Audi
Service Facility for assistance in these situations.
A WARNING
-Please note that the tire mob ility kit cannot
be used in all situations, and that it may on
ly be used temporarily.
- The tire sealant must not come in contact with skin, eyes, or clothes.
- If tire sealant gets in your eyes or on your
skin, thoroughly rinse the affected area im
mediately with clean water.
- Do not inhale the fumes .
- If you swallow any of the tire sealant, thor-
oughly rinse your mouth immediately and
drink a lot of water. Do not induce vomiting .
Seek medical attention immediately.
- Change your clothes immediately if they get
tire sealant on them.
- If an allergic reaction occurs, seek immedi
ate medical attention .
- Keep the tire sealant away from children .
(D Tips
-If sealant leaks, allow it to dry in place. You
can then peel it
off like a sticker.
- Note the expiration date on the sealant bot
tle . Replace the tire sealant at an author
iz ed Audi dealer or authorized Audi Service
Facility.
- Radio reception can be interrupted when
operating the compressor.
- Obey all laws.
Repairing tires
Fig. 274 Components of the tire mobility kit
358
~
"' 0
> u.
m
Fig. 275 Tire mobil ity kit connection
Requirement: the tire mobility kit must be laid
out and ready for use¢
page 357.
Installing the tire mobility kit
"" Open the cover @on the compressor
¢fig. 274 .
"' a, N 0
> u. m
""Remove the connector © and pressure hose®
with pressure gauge from the housing.
""Install the compressor pressure hose® onto
the flange @ on the tir e sealant bottle@.
"" Insert the sealant bottle with the flange at the
bottom into the opening @ on the compressor
cover.
"" Remove the valve cap from the faulty tire.
"" Install the filler hose@on the valve
(J)
¢fig. 275 .
"" Connect the plug©¢ fig. 2 74 to an outlet in
the vehicle .
"" Switch the ignition on.
Inflating a tire
""Move the switch @ ¢fig . 275 on the compres
sor into position
I.
"" Inflate the tire to between 29 psi (200 kPA)
and 36 psi (250 kPA) and read the pressure on
the gauge.
"" If this tire pressure is not reached, remove the
filler hose . Drive slowly approximately 33 feet
( 1 0 m) forward or in reverse so that the sealant
can be distributed in the tire. Pump up the tire
aga in ¢ .&, .
A WARNING
-Read and follow the manufacturer's safety
precautions on the compressor and in the
instructions on the bottle of sealant.
Cl a:, ...... N
" N ,-1 0
0
::r '
reached after inflating for 6 minutes, then
the tire is too severely damaged. Do not
continue driving .
- If the t ire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au
thorized Aud i Serv ice Facility for ass istance .
(D Tips
Do not operate the compressor for more than
six m inutes continuously, or it can overheat.
Once the compressor has cooled, you ca n con
tinue to use it .
Completing
"'Adhere the sticker that says "max . SO mph
(max. 80 km/h)" that is p rovided w it h the t ire
mobility kit within the dr ive r's fie ld of vision.
"' Stop the vehicle afte r driving for about 10 m i
nutes and check the tire pressure .
"' If the tire pressure is lower than 19 psi ( 130
kPA), then the tire is too severely damaged. Do
not cont inue driving.
A WARNING
Pay attent ion to the following after repair ing
the t ire :
- Do not drive faster than SO mph (80 km/h).
- Avoid hard acceleration, brak ing sharply,
and fast cornering.
- The vehicle may become more difficu lt to
contro l.
- If the tire is too severely damaged, see an
authorized Audi dealer or authorized Audi
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Service Facility for disposal.
(D Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Em ergenc y ass is tanc e
Replacing a wheel
Preparation
You must complete the preparation before
changing a tire .
"'Read and follow the impor tant safe ty precau-
tions
¢ page 357.
"'Set the park ing brake .
"' Select the "P" selector lever position .
"' When towing a tra iler : disconnect the trailer
from you r vehicle.
"' Lay out t he vehicle too l kit ¢
page 357 and the
spare tire.
"' Switch on wheel change mode* in the Infotain
ment syst em:
!MENUI button> V ehicle > left
control button >
S erv ic e & ch ecks > Air s uspen
s io n: w heel chang e.
"'Switch the ignit ion off.
The vehicle jack mod e* switches off automatica l
ly at speeds above 6 mph ( 10 km/h).
A WARNING "---
When us ing the ve hicle jack" on a road with a
steep hill or offroad, you must take extra pre
cautions to prevent the vehicle from rolling .
Use su itable objects to block the front and
back of t he wheel t hat is diagonal from the
whee l with the flat t ire.
A WARNING
You o r yo ur passenge rs could be injured while
changing a whee l if you do no t follow these
safety precautions :
- I f yo u have a flat tire, move a safe dis tance
off the road. Turn off the eng ine, turn the
emergency flashers on and use other warn
ing devices to a lert other motorists.
- Make sure that passengers wait in a safe place away from the vehicle and well away
from the road and traff ic.
- To he lp prevent the vehicle from moving
suddenly and possib ly slipping off the jack*,
a lways f ully set the park ing brake and block
the front and back of the wheel diagonally
opposite the wheel being changed. When
one front wheel is lifted off the ground,
~
359
Emergency assistance
placing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack*.
-Always store the vehicle tool kit, the jack* and the replaced tire in the luggage compartment <=>
page 257.
@ Tips
-Obey all laws.
- Before changing the wheel, you must acti- vate the jacking mode*, so that the automatic controls for the air suspension* do
not make it more difficult to lift the vehicle
with the jack*<=>
page 360 .
Removing the caps
Fig .. 276 Wheel: wheel bo lts wi th caps
.,. Slide the plastic clip (from the vehicle tool kit)
onto the cap until it engages
<=> fig. 276 .
.,. Remove the cap with the plastic clip .
Loosening the wheel bolts
Fig. 277 Whee l: loosen ing the w heel bo lt
360
.,. Slide the wheel wrench (from the vehicle tool
kit) all the way onto the wheel bolt .
.,. Turn the wheel bolt approximately one turn to
the left -arrow- . To reach the required torque,
hold the end of the wheel wrench. lfthe wheel
bolt will not loosen, press carefully on the
wheel wrench with your foot . H old onto the ve
hicle securely whi le during this and make sure
your stance is stable.
_&. WARNING
To reduce the risk of an accident, only loosen
the wheel bolts gently (one turn) before rais
ing the vehicle with the vehicle jack*.
Raising the vehicle
Fig. 278 S ill panels: markings
Fig. 279 Sill: positi on ing the vehicle jack
.,. Place the veh icle jack* (vehicle tool kit) on a
firm s urface. Use a flat, stable support if neces
sary . On a slippery surface such as ti le, you
should use a non-slip pad (such as a rubber
mat)
c> .&_ .
.,. Find the marking on the sill that is closest to
the tire that wi ll be changed<=>
fig. 278. Behind
the mark ing, there is a lifting point o n the side
sill for the vehicle jack* . ..,.
Emergency assistance
vehicle tool kit) ¢ fig. 280 and place it on a
clean surface.
• Then install the alignment pin (from the vehicle
tool kit) by hand into the empty wheel bolt hole
¢fig. 2a11>.
• Remove the rest of the wheel bolts .
• Remove the wheel ¢@ . The al ignment pi n re-
mains in the hole while doing this .
Install a wheel
Read the direct ions on c> page 362 when instal
ling unid irectional tires.
• Slide the wheel on over the alignment pin¢@ .
• Install the wheel bolts and tighten gently using
the hex socket.
• Remove the alignment pin and also tighten the
remaining wheel bolt.
• Carefully lower the vehicle using the vehicle
jack* .
• Tighte n the wheel bolts in a diagona l pattern
u sin g the wheel wrench.
The whee l bolts must be clean and loosen/tight
en easi ly. Check the contact su rfaces for the
wheel and hub . Contaminants on these surfaces
m ust be removed before installing the wheel.
A WARNING
Never use the hex socket in the screwdriver
hand le or the hex socket wrench with the
ratchet to loosen or tighten the wheel bolts.
You will not attain the required tightening
specification, which wi ll increase the risk of an
accident .
@ Note
When removing or installing the whee l, the
r im could hit the brake rotor and damage the
rotor. Work carefu lly and have a second per
son help you.
-
1
> A pp lies to vehicles with cer amic br ake rot ors*: use a sec
on d alignment pin * (fro m th e ve hicle t ool kit) for th e low
e st hole ac co rding t o the steps de scribed for the first
al ig nm ent pin.
362
(D Tips
-When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way
c> page 362.
-Th e wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be
fore remounting the wheel.
Unidirectional tires
A un idirectional tire profi le is identified by arrows
that point in the running direct ion on the tire
s idewa ll. You must always adhere to the speci
fied running direction. This is necessary ensure
t h e tire's optimum performance in regard to ad
hesion, running noise, friction and hydroplaning .
To benefit fully from the advantages of the uni
directional tire design, you should rep lace fau lty
tires as soon as possible and restore the correct
running direction on all of the tires.
Finishing
• Reinstall the caps on the wheel bolts if neces
sary.
• Store the veh icle tool k it in its designated
place .
• Store the replaced tire securely in the luggage
compa rtment
¢page 257.
• Check the tire pressure on the insta lled wheel
as soon as possible.
• Cor rect the tire pressure and store it in the In
fotainment system ¢
page 349.
• The wheel bolt tightening specification must be
120 ft lbs (160 Nm). Check it as soon as possi
ble with a torque wrench. Drive carefully until
then .
• Have the faulty wheel replaced as quickly as
possible .
Cl a:, ...... N
" N ,-1 0
0
::r '
-If you notice t hat the wheel bolts are cor
r oded and diffic ult to turn w hile chan gin g a
tire, they should be rep laced befo re yo u
chec k th e ti ghtening torque.
- D rive a t reduced speed until you have the
ti ghtening torques c hecked.
Notes on wheel changing
P lease read the i nfo rmation r=> page 33 7 if you
a re go ing to use a replaceme nt tire which i s dif
fe rent from the tires on you r ve hicl e.
Afte r you change a t ire:
- Check the tire pressure on the replacement
tire immediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos
sible by your authorized Audi dealer or quali
fied workshop.
- With steel and alloy wheel rims , the wheel
bolts a re correctly tightened at a torque of
120 ft lbs (160 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
A WARNING
- If you ar e going to equip your ve hicle w it h
t ir es o r rims w hich differ fr om thos e which
w ere factory ins talled , th en b e sur e to read
t h e info rm at ion
<=> page 337 .
-Always ma ke sur e the damaged wh eel or
e ven a flat tir e an d th e jack* and tool kit ar e
p ro pe rly se cured i n the luggage com part
me nt a nd are n ot lo ose in the p assenger
c omp artmen t.
- I n an a ccide nt or sud den mane uve r they
co uld fly forwar d, injuring anyone in t he ve
hicle .
-
Emergency assistance
-Always s tore damaged wheel, jac k* and
too ls sec urely in the lug gage com partment .
Oth erwise, in an acc ident or sud den maneu
v e r th ey could fly forward, causing in jury to
pass engers in t he v ehicle .
363
Fuses and bulbs
Fuses and bulbs
Fuses
Replacing fuses
A fuse that has blown will have metal strips that
have burned through.
Fig . 282 @ Dr iver footwell (left-hand drive vehicle): foot
rest, @ Front passenger footwe ll (right-hand drive veh icle):
cover
364
©
F ig. 283 © Drive r's side of the cockp it (left -hand drive ve
h icle/r igh t- h and drive ve hicle): cover, @ Left s ide of l ug
gage compartment: cover
The fuses are located in the footwell under the
foot rest ( left-hand drive vehicle) @
¢fig . 282 o r
behind the cove r (right-hand d rive vehicle) @.
Additional fuses are located on the front side of
the cockpit (driver's side) ©¢
fig. 283 and under
the left cover in the luggage compartment @.
.,. Switch the ignit io n and a ll electrical eq uipment
off .
.,. Check the following tab le to see wh ich fuse be·
longs to the equipment .
.,. Remove the screwdr iver and the revers ible To rx
bit from the vehicle tool kit ¢
page 357 .
.,. Remove the foot rest or the co rrespo nding cov
er.
.,. Remove the co lored plast ic cli p from the f use
pa ne l, if necessary ¢
page 365, fig . 284. Yo u
can dispose of the plastic clip .
.,. Remove the clamp from the rear side of the
cover @ .
.,. Remove the fuse us ing the clamp .
.,. Rep lace the blown fuse on ly w ith an identical
new one .
.,. Reat tach the footrest o r the cover.
Fuses and bulb s
Fuse panel@ (red )
11 AdBlue heating
12 Third row seats
Fus e panel © (brown)
N o. Equip ment
2 Telephone
3 Lumba r suppo rt
4 Audi side assist
8 Sma rt mod ule (tank)
9 CD /DVD player
12 Homelink
13 Rearview camera, per
ipheral cameras
14 Right tail lights
16 Right safety belt tensioner
Fu se panel @ (red )
N o.
I Equipment
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you.
I t is becoming increasing ly more and more diffi
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re moved before you are able to get to the bulb.
This applies espec ially to the light bulbs in the
front of your car wh ich you can only reach
through the eng ine compartment.
Sheet metal and bulb ho lders can have sharp
edges that can cause ser ious cuts, parts must be
correctly taken apart and then properly put back
together to help prevent breakage of parts and long term damage from water that can enter
housings that have not been proper ly resea led.
For your safety, we recommend that you have
your author ized Audi dealer replace any bulbs for
you, s ince your dealer has the proper tools, the
correct bulbs and the expert ise.
G as disc harg e la m ps (Xe non light s):
368
Due to the high e lectrica l voltage, have the bulbs
rep laced by a qualified technician. Headlights
with Xenon light are identif ied by the high volt
age sticker.
LED h eadlights*
LE D headlights requ ire no maintenance. Please
contact your author ized Audi dealer if a bulb
needs to be rep laced.
& WARNING
Changing Xenon lamps without the necessary
equipment can cause serious personal injury.
- Bulbs are pressurized and can exp lode when
being changed. Potential risk of injury!
- On veh icles equipped with gas discharge
bulbs (Xenon light) life -threatening injuries
can result from improper handling of the high-vo ltage portions of such lamps!
- On ly your authorized A udi dealer or quali
fied workshop shou ld change the bulbs in
gas discharge lamps. There are parts with
sharp edges on the openings and on the bulb holders that can cause serious cuts . If
you are uncerta in about what to do, have
the work performed by an authorized Audi
dea le r o r qualified workshop. Ser ious per
sonal injury may result from improperly per
formed work.
© Tips
- If you still prefer to replace the light bulbs
yourself, be awa re that the engine compa rt
ment is a hazardous area to work in ~ .&.
in
Working in the engine compartment on
page 319 .
-It is best to ask your authorized Audi dealer
whenever you want to change a bulb .