2018 AUDI Q7 trailer

Parking systems
Switching on/off
Applies to: ve hicles w ith per ip heral cameras
Fig. 138 Infotainment system: se lect the mode
Switching on/off
"' Press the p,qA button in the center console
¢ page 134, fig. 129. A short confirmation
tone sounds and the LED in the button turns
on .
Switching on automatically
The system switches on a utomatica lly when re­
ve rse gear is engaged while the engine is run­
n ing. A brief confirmation tone will sound.
Switching off automatically
The system switches off automatically when dr iv­
ing forward faster than 6 mph (10 km/h) .
Selecting the mode
"'Turn the control knob to the symbol for the de­
sired mode @through ©¢fig. 138 and press
the control knob .
You may select from the following modes:
@ -Corner view (front)¢ page 138
@ -Front¢ page 138
© -Area ¢ page 139
@ ·Rear ¢ page 139
© -Corner view (rear) ¢ page 138
You can also switch to trailer view¢ page 136.
138
Corner view (front)/corner view (rear)
Applies to : vehicles with peripheral cameras
Fig. 139 Infota inment system: Corner view (front)
Fig. 140 Infota inmen t system : Corner view (rear)
This view can assist you for example, when you
are exiting from an area with poor visibi lity. The
area at the front and rear sides of the veh icles is
displayed.
"' To show the side view toward the front, select
the symbol @¢
fig. 139 with the control knob
and press the control knob .
"' To show the side v iew toward the rear, se lect
the symbol ©¢ fig. 140 with the con trol knob
and press the control knob.
Front
Applies to: vehicles wi th peripheral ca meras
Fig. 1 41 Infota inment system: front mode
This view assists you for example, in using the
full maneuvering range in front of the vehicle.
The area in front of the vehicle is displayed. The
vehicle surround ings are shown in the right area
Ill>

Parking syste m s
Adjusting the parking aid
Applies to: vehicles with a rear parking system/parking sys­
tem plus/rearview camera/peripheral cameras
The functions are adjusted in the Infotainment
system .
.,. Se lect in the Infota inment system: IM ENU I but­
ton
> Vehi cle > left contro l bu tton > Driv er a s­
s is ta nce > Par kin g aid .
Or
.,. When the parking aid is active, se lect in the In -
fotainment system : rig ht contro l button *.
End sy stem * -stop t he parking aid
Acti vate automaticall y* -switch automatic acti­
vation on/off
Front volume * -volume for the front area
Rear volume -volume for th e re ar ar ea
Entertainm ent f ader -the vol ume of t he aud io/
video source is lowered when t he parking system
is turned on.
The new value is g iven b riefly du ring the adjus t­
ment.
Vie w* -switch between an optical d isplay
( Graphic ) and camera image ( Cam era ) in the
r ight section of the display.
Tr ail er view * -show trailer view
*Auto. front /rear came ra change * -the view be­
h ind the veh icle
( Rear mode) is displayed auto­
mat ically when you shift into reverse gear. The
v iew in front of the vehicle
( Front mode) is d is ­
played automatically when you shift into the for­
ward gea rs. When first activat ing in a forward
gea r with the
P,, 1~ button, the front s ide v iew is
d isp layed
( Corn er view (fr ont ) mode).
If you do not set the./, the view behind the vehi­
cle
( Rear mode) is a lways d isplayed and it does
not swi tch to the
Front mode whe n a forward
gea r is selec ted .
(0 Tips
-Seve ral menus can be accessed w ith the
r ight contro l button only when the park ing
a id is ac tive.
- The settings for volume and automatic act i­
vation* are au toma tically s to red and as-
140
signed to the remote control key be ing
used .
Error messages
Applies to: vehicles with a rear parking system/parking sys­
tem plus/rearview camera/peripheral cameras
Ill Rear parking aid : malfunction! Obstacles
cannot b e dete cted
Ill Front par king aid: m alfunction! Obstacles
cannot b e detected
Ill Pa rking aid : malfunct ion ! Obstacles cannot
b e detected
When one of these messages appears, there is a
system malfunction. The L ED in the
Pw, button al­
so blinks when sw itching it on. The relevant mes­
sage on ly appears again when you manually acti­
vate the park ing aid with the button .
[ii Rear parking aid: obstacle detection re stri ct­
ed
The rear cross -traffic assist* ¢ page 124, Rear
cross-traffic assist
is not available. Either the ESC
i s sw itched off, or the radar sensors may be cov ­
ered by a bike rack, stickers, leaves, snow or oth­
er objects. Swi tch the ESC on , or clean the area in
front of the sensors if necessary¢
page 121,
fig . 115 .
If this message cont inues to be d is­
played, drive immed iate ly to an authori zed Audi
dealer or author ized A udi Service Fac il ity to have
t h e mal funct ion repaired .
Parking system plus *
If a sensor or speaker is faulty, the IM symbol
will appear in front of/behind the vehicle in the
Infotai nment system d isplay. If a rear sensor is
faulty, only obs tacles that are in areas @ and @
are show n
¢page 133, fig. 128 . If a front senso r
i s fa ulty, only obstacles that are in areas © and
@ are s hown.
Peripheral cameras*
There is a system malfunction if the% symbol
appea rs and the co rresponding area of the dis ­
play is shown in black . The camera is no t wo rking
in this area.

Cl a:, .... N
" N .... 0
0
::r ' Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunct ion corrected.
Trailer hitch
Applies to: vehicles with a rear parking system/parking sys­
tem plus/ rearv iew camera/peripheral cameras and trailer
hitc h
When the tra iler socket is in use, the parking sys­
tem rear sensors are not activated when you shift into reverse gear or when you press the
Pw~ but­
ton. This results in the following restrictions.
Rear parking system*
There is no distance warning.
Parking system plus*
There is no distance warning for the rear. The
front sensors remain activated . The visual display
switches to trai ler mode.
Rearview camera* /peripheral cameras*
There is no distance warning for the rear. The
front sensors remain activated. The visual display
switches to trai ler mode. The rearview camera
image will not show the orientation lines and the
b lue surfaces.
@ Tips
Trailer hitches that are not installed at the
factory may cause the parking system to ma l­
function or they may restrict its function.
Parking systems
141

a co ...... N r--. N ...... 0
0
:E ' Map
Map operation
Applies to: veh icles with navigation system
Fig. 192 Example: 30 map with the c ross hair s switched off
--,-
@
Fig. 193 Examp le: stan da rd map with t he crosshai rs
sw itc hed on
~ Press the I NAV /MAPI button repeatedly until
the map is displayed
c;,fig. 192.
Zooming in/out on the map
- Turn the control knob to the left or to the right.
Alternatively, you can also zoom in/out on the
map using the MMI touch control pad*
¢ page 154, if the crosshairs are switched on.
Or: turn the left thumbwheel on the mu ltifunc­
tion steering wheel*¢
page 13.
Turning the crosshairs on/off
- Switching the crosshairs on :
press the control
knob in the map view
¢fig. 192.
- Switching the crosshairs off: press the I BACKI
button .
When the crosshairs are switched off¢ fig. 192 :
(D Direction. For additional information, see
¢page 215.
@ The distance to the destination includes the
calculated arrival time.
1l Only appl ies to vehicl es w ithou t camer a-b as ed speed lim it
d ispla y.
Navigation
@ When the trailer mode function is switched
on~, the corresponding symbol is displayed
next to the arrival time.
@ Scale: turn the control knob to the left or
right to decrease or increase the scale. When
the
Automatic zoom function is sw itched on
~, an "A" for "Automat ic " is displayed in the
magnifying gla ss.
® Altitude
@ Vehicle position
0 Route information: various information will
be displayed during active route guidance
(for example, the upcoming maneuver in­
cluding calculated distance and street
names) . The display also provides traffic in­
formation or points of interest on the current route .
® Road currently being driven on
When the crosshairs are switched on¢ fig. 193 :
® The crosshairs: move the crosshairs in the de-
s ired direction and set a po int on the map us­
ing the MMI touch control pad* or the con­
t rol knob . When the crosshairs are turned
off, the road being currently driven on is
shown.
@ Speed limit display1>: display of the maxi­
mum perm itted speed on the expressways
and highways .
@ Entertainment sliding menu*: see
¢page 155 .
@ Additional information on the crosshairs po­
sit ion: if you move the crosshairs to a loca­
t ion on the map, available information for
the current posit ion is displayed . Tap briefly
on the MMI touch control pad.
Or: press the
control knob. In the destination details, you
can start route guidance to the displayed lo ­
cation. Select and confirm
Start route guid­
ance.
@ Map contents (points of interest, favorites) .
When there are multiple points of interest in
the immediate vicin ity, the symbols are
shown stacked on the map.
213

0 a, .... N
" N .... 0
0
l: ..
& WARNIN G
Please note the important safe­
ty precautions regarding tire
pressure
c:::> page 340 and load
limits
c:::>poge 343.
Tires and vehicle load limits
There are limits to the amount of
load or weight that any vehicle
and any tire can carry. A vehicle
that is overloaded will not handle
well and is more difficult to stop.
Overloading can not only lead to
loss of vehicle control, but can al­
so damage important parts of the
vehicle and can lead to sudden
tire failure, including a blowout
and sudden deflation that can
cause the vehicle to crash .
Your safety and that of your pas­ sengers also depends on making
sure that load limits are not ex­
ceeded . Veh icle load includes ev­
erybody and everything in and on
the vehicle . These load limits are
technically referred to as the vehi­
cle's
Gross Vehicle Weight Rat ­
ing ("GVWR").
The "GVWR" includes the weight
of the basic vehicle, all factory in­
stalled accessories, a full tank of
fuel, oil, coolant and other fluids
Wheels
plus maximum load . The maxi­
mum load includes the number of
passengers that the vehicle is in­
tended to carry ("seating capaci­
ty ") with an assumed weight of
150 lbs. (68 kg) for each passen ­
ger at a designated seating posi­
tion and the total weight of any
luggage in the vehicle . If you tow
a trailer, the weight of the trailer
hitch and the tongue weight of
the loaded trailer must be includ­ ed as part of the vehicle load .
The
Gross A xle Weight Rating
(" GAWR ") is the maximum load
that can be applied at each of the
vehicle's two axles.
T he fact that there is an upper
limit to your vehicle 's Gross Vehi­
cle Weight Rating means that the
total weight of whatever is being
carried in the vehicle (including
the weight of a trailer hitch and
the tongue weight of the loaded
trai ler) is lim ited. The more pas­
sengers in the vehicle or passen ­
gers who are heavier than the
standard weights assumed mean
that less weight can be carried as luggage.
The Gross Vehicle Weight Rating and the Gross Axle Weight Rating .,.
34 3

Wheels
are listed on the safety compli­
ance sticker label located on the
driver's side B-pillar.
A WARNING ,-= · -
Overloading a vehicle can cause
loss of vehicle control, a crash
or other accident, serious per­
sonal injury, and even death .
-Carrying more weight than your vehicle was designed to carry will prevent the vehicle
from handling properly and i ncrease the risk of the loss of
vehicle control.
-The brakes on a veh icle that
has been overloaded may not
be able to stop the vehicle
within a safe distance.
-Tires on a vehicle that has been overloaded can fail sud­
denly, including a b lowout and
sudden deflation, causing loss
of contro l and a crash.
-Always make sure that the to­ tal load being transported -i nc luding the weight of a tra il­
er hitch and the tongue
weight of a loaded trailer­
does not make the vehicle
h eavier than the vehicle's
Gross Vehicle Weight Rating.
3 44
Determining correct load
limit
Use the example below to calcu­
late the tota l weight of the pas­
sengers and luggage or other
things that you plan to transport
so that you can make sure that
your vehicle will not be over load ­
ed.
Steps for Determining Correct Load Limit
1 . Locate the statement " TH E
COMBIN ED WE IGH T OF OCC U­
PANTS AND CARGO SHOU LD
NEVER EXCEED XXX KG OR XXX
LBS" on your vehic le's placard
(tire inflation pressure label)
¢ page 340, fig . 272 .
2. Determine the combined
weight of the drive r and pas­
sengers that will be riding in
your vehicle.
3. Subtract the combined weight
of the driver and passengers
from
"XXX" kilograms or "XXX"
pounds shown on the stick­
er ¢
page 340, fig. 272 .
4. The resu lting figure equa ls the
available amount of cargo and
luggage load capacity . For ex­
ample, if the "XXX" amount
eq uals 1400 lbs. and there will~

Cl a:, ...... N
" N ,-1 0
0
::r ' -If a tire pressure of 29 psi (200 kPA) cannot
reached after inflating for 6 minutes, then
the tire is too severely damaged. Do not
continue driving .
- If the t ire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au­
thorized Aud i Serv ice Facility for ass istance .
(D Tips
Do not operate the compressor for more than
six m inutes continuously, or it can overheat.
Once the compressor has cooled, you ca n con­
tinue to use it .
Completing
"'Adhere the sticker that says "max . SO mph
(max. 80 km/h)" that is p rovided w it h the t ire
mobility kit within the dr ive r's fie ld of vision.
"' Stop the vehicle afte r driving for about 10 m i­
nutes and check the tire pressure .
"' If the tire pressure is lower than 19 psi ( 130
kPA), then the tire is too severely damaged. Do
not cont inue driving.
A WARNING
Pay attent ion to the following after repair ing
the t ire :
- Do not drive faster than SO mph (80 km/h).
- Avoid hard acceleration, brak ing sharply,
and fast cornering.
- The vehicle may become more difficu lt to
contro l.
- If the tire is too severely damaged, see an
authorized Audi dealer or authorized Audi
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Service Facility for disposal.
(D Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Em ergenc y ass is tanc e
Replacing a wheel
Preparation
You must complete the preparation before
changing a tire .
"'Read and follow the impor tant safe ty precau-
tions
¢ page 357.
"'Set the park ing brake .
"' Select the "P" selector lever position .
"' When towing a tra iler : disconnect the trailer
from you r vehicle.
"' Lay out t he vehicle too l kit ¢
page 357 and the
spare tire.
"' Switch on wheel change mode* in the Infotain­
ment syst em:
!MENUI button> V ehicle > left
control button >
S erv ic e & ch ecks > Air s uspen­
s io n: w heel chang e.
"'Switch the ignit ion off.
The vehicle jack mod e* switches off automatica l­
ly at speeds above 6 mph ( 10 km/h).
A WARNING "---
When us ing the ve hicle jack" on a road with a
steep hill or offroad, you must take extra pre ­
cautions to prevent the vehicle from rolling .
Use su itable objects to block the front and
back of t he wheel t hat is diagonal from the
whee l with the flat t ire.
A WARNING
You o r yo ur passenge rs could be injured while
changing a whee l if you do no t follow these
safety precautions :
- I f yo u have a flat tire, move a safe dis tance
off the road. Turn off the eng ine, turn the
emergency flashers on and use other warn ­
ing devices to a lert other motorists.
- Make sure that passengers wait in a safe place away from the vehicle and well away
from the road and traff ic.
- To he lp prevent the vehicle from moving
suddenly and possib ly slipping off the jack*,
a lways f ully set the park ing brake and block
the front and back of the wheel diagonally
opposite the wheel being changed. When
one front wheel is lifted off the ground,
~
359

Emergency situations
,.. Or: pull sharply on the trim in the direction of
the arrow to remove
¢fig. 291.
,.. Tighten the towing loop in the threaded open ­
ing until it stops and then tighten it with a
wheel wrench.
,.. After using, place the towing loop back in the
vehicle tool kit.
,& WARNING
If the towing loop is not tightened until it
stops when insta lling, the threads may be
pulled out when towing the vehicle and tha t
could cause an accident .
(D Note
The trim is attached to the bumper with sev­
eral hooks. To redu ce the r isk of damage, do
not use any force when removing and instal­
ling.
Rear towing loop
Fig. 292 Rear bumper: installing the tow ing loop
Vehicles with a towing loop
On veh icles w ithout a factory-installed trailer
h itch*, the towing loop threads are located on
the right rear side of the bumper.
-
,.. Remove the tow ing loop from the veh icle tool
kit
¢page 357.
• Press the cap inward with b rief, forcefu l pres­
s u re~
fig. 292. The cap will loosen from the
bumper.
.. Tighten the towing loop in the threaded open ­
ing until it stops and then tighten it with a
wheel wrench.
,.. After using, place the towing loop back in the
vehicle tool kit.
372
Vehicles with a trailer hitch*
"' Attach the towing bar or the towing cable to
the trailer hitch.
Vehicles with a factory-installed trailer hitch* are
not equipped with towing loop threads at the
r ear.
,& WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when towing the vehicle and that
could cause an accident.
A WARNING
Applies to: vehicles with trailer hitch
-Only use a special towing bar to prevent
damaging the ball hitch. These towing bars
have been specially designed for trailer tow­
ing h itches.
- Only use special towing cables.
Loading the vehicle onto a flatbed truck
Fig. 293 Ve hicle on flatbed truck
Front hook up
.. Align the vehicle with the centerline of the car
carrier ramp.
• Attach the winch hook to the front towline eye
previously installed .
Rear hook up
,.. Align the vehicle with the centerline of the car
carrier ramp.
• Attach the w inch hook to the rear towline eye
previously installed . ..,