2018 AUDI A8 flat tire

Drivin g
-Avoid driving through sa lt water, because
this can cause corrosion .
Economical and environmentally-friendly
driving
The amount of fuel consumption, the env iron­
mental impact and the wear to the engine,
brakes and t ires depends mostly on your dr iv ing
style. W it h an anticipatory and economic dr iv ing
style , fu el consumption can be reduced by ap ­
p roximate ly 10 -15% . The following tips wi ll help
you conserve the environment and your money at the same time .
Anticipatory driving
A veh icle uses the most fuel when acce le rating.
When you dr ive with ant ic ipat io n, you do no t
need to brake as often and so you accelerate less .
When possib le, let your vehicle coast with a
gear
eng aged ,
for example, when you notice that the
next traffic light is red. This produces an engine
braking effect, which helps to protect the brakes
and tires and reduces the emissions and fuel con­
sumpt ion to zero (fuel shut -off during decelera­
tion) .
Shift efficientl y
Upshifting earlier is an effective way to save fuel.
Staying in a gear too long uses fue l unnecessari­
ly . Press down on the accelerator pedal slowly
and avoid "k ick-down" .
Avoid full accel eration
You shou ld rare ly trave l at the maximum vehicle
speed. High speeds cause a disproportionately h igh increase in fuel consumption, emissions and
traffic no ise . Slower driving saves fuel.
Reduce idlin g time
The Start/Stop system* he lps to reduce the idling
time automatically. In vehicles without the Start/
Stop system*, it is efficient to switch the eng ine
off when stopped at ra ilroad crossings and long
red l ights . Stopp ing the engine for 30 -40 sec­
onds already saves more fuel than the amount of
ext ra fuel needed to resta rt the eng ine.
74
It takes a ve ry long time in id le to warm the en­
gine up to operating temperature. Wear and
emissions are especially high in the warm -up
phase. Therefore, you shou ld begin driving im­
med iate ly after starting the engine. Avoid high
RPMs while doing this .
Hav e maintenance perfo rmed regul arly
By having maintenance performed reg ularly on
your vehicle, you can help to reduce fuel con­
sumption before you even start to drive. The maintenance condition of your vehicle not on ly
affects traffic safety and long-term value but al­
so impacts fuel consumpt ion. A poorly main­
ta ined engine can lead to fuel consumpt ion that
i s 10% hig he r th an no rma l.
Avoid short trip s
The engine and exhaust cleaning system must
reach their optimal operat ing temperature to ef­
fect ively reduce consumpt ion and emissions .
A cold engine uses a d isproportionately high
amount of fuel. The engine reaches operat ing
temperature and consumption normalizes only
after approximately 2 .5 m iles (4 km) .
Check the tire pressu re
To save fue l, make sure the t ires are always in­
flated to the correct pressure
¢ page 291. The
fuel consumpt ion can increase by 5% if the pres­
sure is only 0 .5 bar too low . Due to the increased
r oll ing resistance, low tire p ressures w ill also
l ead to greater tire wear and will affe ct driv ing
behav ior.
Drive w ith summer tires when poss ible because
t hi s can increase fue l economy by up to 10% .
Eliminate unnecessary weight
Since every pound of extra weight increases fuel
consumption, it pays to remove any unnecessary
weight.
A roof rack increases the w ind resistance on the
vehicle and shou ld be removed when it is not
needed. You will save approximately 12% of your
fuel when at speeds from 62-75 mph (100-120 km/ h).
.,.

Trailer towing
Trailer load distribution
Be sure the load in the trailer is held securely in
p la ce to prevent it from shifting forward, back­
ward or sideways .
Never allow a passenger to ride in a trailer~&.
in Driving instructions on page 91.
Engine cooling system
Towing a trailer makes the engine work harder . It
is important that the coo ling system's perform­
ance is up to t he additional load. Make sure that
the cooling system has eno ugh fluid .
Tire pressure
When tow ing a tra iler, inflate the tires of your
veh icle to the tire pressure listed under "Full
load " on the label
~ page 293. Inflate trailer
tires to trailer and tir e ma nufactu rers' specifica­
tions.
Lights
Check to make sure both vehicle and trailer lights
are working properly .
Safety chains
Be sure trailer safety chains are proper ly connect­
ed from the trailer to the hitch on the vehicle.
Leave enough slack in the chains to permit turn­
ing corners . When you install safety cha ins, make
sure they w ill not drag on the road when you are
driving.
The chains should cross under the trailer tongue
to prevent it from dropping in case of separation
from the hitch .
Adjusting the Audi drive select
Make sure the vehicle is on a level surface before
hitching up the trailer and before adjust ing the
tongue we ight. The vehicle must be in
auto or
comfort driving mode and not ra ised
~ page 111, ~0 .
Make sure that the vehicle is lowered. In Info­
tainment, select:
ICARI function butto n> Lower
control button.
90
If you must drive under poor road conditions, you
can raise the ve hicle
after coupling the trailer or
after adjust ing the tongue we ight ~ page 113.
@ Note
-Changes in temperature or load can aff ect
the height of the vehicle .
-Always select auto or comfort mode. Other­
wise, the tong ue load specified for your ve­
hicle will no longer be applicab le .
Driving instructions
Driving with a trailer always requires extra care
and consideration.
Weight distribution
Towing a loaded trailer with an empty car results
in a hig hly unstable distribution of we ight. If th is
cannot be avoided, drive at very low speeds only
to avoid t he risk of losing steering contro l.
A "balanced" rig is eas ier to operate and control.
This means that the tow vehicle s hould be loaded
to
the extent possible and permissib le, w hil e
keeping the trailer as light as possible under the
circumstances. Whenever possible, transfer
some cargo to the luggage compartment of the
tow veh icle while observing tongue load require­
ments and vehicle loading considerations.
Speed
The higher the speed, the more difficu lt it be ­
comes for the driver to control the rig . Do not
drive at the maximum permissible speed. Reduce
your speed even more if load, weather or wind cond it ions are unfavorable - particularly whe n
go ing down hill.
Reduce vehicle speed
immediately if the trailer
shows the slightest sign of sway ing.
Do not try
to stop the swaying by accelerating.
Observe speed limits. In some areas, speeds for
vehicles towing trailers are lower than for regular
vehicles.
A lways apply brakes early. When driving down­
hill, shift into a lower gear to use the engine
braking effect to slow the vehicle. Use of the
brakes alone can cause them to overheat and fail.
ll-

lL t:0 ....
"' ......
"' .... 0 0 :c ' ~ ALWA YS adjust you r sp eed to road , traffic and
weather conditions.
~ Take frequent breaks on long trips. Do not drive
for more than two hours at a stretch.
~ Do NOT drive when you are tired, under pres­
s ure or when you are stressed .
A WARNING
Impaired driv ing safety increases the risk of
ser ious personal inj ury and death whenever a
vehicle is being used .
Correct passenger
seating positions
Proper seating position for the driver
The proper driver sea ting po sit ion is impor tan t
for safe, relaxed driving .
Fig. 217 Correc t seat ing posit ion
F or your own s afety and to reduce the risk of in ­
jury in the event of an accident, we recommend
that you adjust the driver 's seat to the following
position :
~ Adjust the dr iver's seat so tha t you can easily
push the pedals all the way to the f loor wh ile
keeping your knee(s) s light ly bent
c:!;> _& .
~ Adjust the ang le of the seatback so that it is in
an upright position so that your back comes in
full contact w ith it when you drive.
~ Adjust the steering wheel so that there is a dis­
tance of at least 10 inches (25 cm) between the
stee ring wheel and you r breast bone
<:!;> fig . 217 .
If no t possib le, see you r autho riz ed Aud i dea l­
ersh ip about adaptive equipment .
Driving safety
~ Adjust the steering wheel so that the steering
wheel and airbag
cover points at your chest and
not at yo ur face.
~ Grasp the top of the steering wheel with you r
elbow(s) slightly bent.
~ Adjust the head restraint so the upper edge is
as
even as possible w ith the top of your head . If
that is not possible, t ry to adjust the head re­
s traint so that it is as close to this posit ion as
possible .
~ Fasten and wear safety belts correctly
c:!;> page 2 2 2.
~ Always keep both feet in the footwell so that
you are in contro l of the ve hicle at a ll times .
F or detailed information on how to adj ust the
driver's seat,
see r:!;> page 54 .
A WARNING
-
Drivers who are unbelted, out of position or
too close to the airbag can be se riously in­
jured by an airbag as it unfolds. To help re­ duce the risk of serious personal injury:
- Always ad just the driver's seat and the
steer ing whee l so that there are at least
10 inc hes (25 cm) between you r breastbone
and the steer ing wheel.
- Always ad just the d river's seat and the
steer ing wheel so that there are at least
4 inches (10 cm) between the knees and the
lowe r part of the instrument panel.
- Always hold the steering w heel on the out­
side of the steering wheel r im with yo ur
hands at the 9 o'clock and 3 o'clock posi­
tions to help reduce the risk of personal in­
jury if the driver's airbag inflates.
- N ever hold the stee ring wheel at the
12 o' clock position o r wi th yo ur hands at
other posi tions i nside the steer ing whee l
rim or on the steering wheel hub . Holding
the steering wheel the wrong way can cause
serio us injuries to the hands, arms and head
if the dr iver's airbag inf lates .
- Pointing the steering wheel toward your
face decreases the abi lity of the supplemen­
tal driver's airbag to protect you in a coll i-
sion .
..,
209

Drivin g saf ety
A WARNING
Improperly stored luggage or other items can
fly through the vehicle causing serious per­ sonal injury in the event of hard braking or an
accident. To help reduce the risk of serious
personal injury:
- Always put objects, for example, luggage or other heavy items in the luggage compart­
ment.
- Always secure objects in the luggage com­
partment using the tie-down hooks and
suitable straps .
A WARNING
Heavy loads will influence the way your vehi­
cle handles. To help reduce the r isk of a loss
of control leading to serious pe rsonal injury:
- Always keep in mind when transporting heavy objects, that a change in the center of
grav ity can also cause changes in vehicle
hand ling:
- Always distribute the load as even ly as
possible.
- Place heavy objects as far forward in the
luggage compartment as poss ible.
- Never exceed the Gross Axle Weight Rating
o r the Gross Vehicle Weight Rating specified
on the safety compliance sticker on the left
doo r jamb. Exceed ing permissible weight
standards can cause the vehicle to slide and
hand le differently .
- Please observe information on safe driving
c> page 208.
A WARNING
To help prevent poisonous exhaust gas from
being d rawn into the vehicle, always keep the
rear lid closed whi le driving.
- Never transport objec ts larger than those
fi tt ing complete ly into the luggage a rea be­
ca use the rear l id cannot be fully closed.
- If you absolutely mus t drive w ith the rea r lid
open, obse rve the follow ing notes to reduce
t h e risk of poisoning:
- Close all windows,
- Close the power roof,
214
-
- Open all a ir outlets in the instrument pan­
el,
- Switch off the air reci rculat ion
'
- Set the fresh air fan to the highest speed .
A WARNING -
Always make su re that the doo rs, all win ­
dows, the powe r roof and the rear lid are se­
curely closed and locked to re duce the risk of
in jury when the veh icle is not being used.
- After closing the rear lid, always ma ke sure
that it is properly closed and locked.
- Never leave your veh icle unattended espe­
cially with the rear lid left open . A child
could crawl into the vehicle through the lug­
gage compartment and close the rea r lid be­
coming trapped and unab le to get o ut. Be­
ing trapped in a vehicle can lead to ser ious
pe rsonal injury.
- Never let ch ildren play in o r around the vehi­
cle.
- Never let passengers ride in the luggage
compa rtment . Vehicle occupants mus t al­
ways be properly restrained in one of the ve­ hicle's seat ing pos itions.
(D Tips
- Air circulation helps to reduce w indow fog­
ging . Stale ai r esca pes to the outs ide
through vents in the trim panel, on the left
side of the luggage compartment. Be sure
to keep t hese s lo ts free and open.
- T he tire p ressure must correspond to the
load. The t ire pressure is shown on t he tire
press ure label. The ti re pre ssure label is lo­
c ated on the drive r's side B- pilla r. The tire
pressu re label lists the recommen ded cold
t ire inflation pressures fo r the veh icle at its
maximum capac ity we ight and the tires that
we re on your veh icle at the time it was man­
ufactured . For recommended t ire pressures
for normal load conditions, p lease see chap­
ter
c> page 294.

u. a:, .... N
" N .... 0
0
I Wheels
Wheels and Tires
General information
~check your tires regularly for
damage (punctures, cuts, cracks
and bulges). Remove foreign ob­
jects from the tire tread.
~ If driving over curbs or similar
obstacles, drive slowly and ap ­
proach the curb at an angle.
~Have faulty tires or rims re­
placed immediately.
~Protect your tires from oil,
grease and fuel.
~Mark tires before removing
them so that the same running
direction can be maintained if
they are reinstalled.
~Lay tires flat when storing and
store them in a cool, dry location
with as little exposure to light as possible.
(D Note
-Please note that summer and winter tires are designed for
the conditions that are typical in those seasons. Audi recom­
mends using winter tires dur­
ing the winter months. Low
temperatures significantly de­
crease the elasticity of summ­
er tires, which affects traction
Wheels
and braking ability. If summer
tires are used in very cold
temperatures, cracks can form on the tread bars, resulting in
permanent tire damage that
can cause loud driving noise
and unbalanced tires.
-Burnished, polished or chromed rims must not be
used in winter driving condi­
tions. The surface of the rims does not have sufficient corro­
sion protection for this and
could be permanently dam­
aged by road salt or similar
substances.
Tire designations
Fig. 264 Tire specification codes on the
sidewall of a tire
.,.
283

....
"' -N .... N
-0
0
J: ..
® Mud and snow capability
"M/S" or "M+S" indicates the tire
has properties making it suitable
to drive in mud or
snow .~ indi­
cates a winter tire .
@ Composition of the tire cord
and m aterials
The number of plies indicates the
number of rubberized fabric lay­
ers in the tire. In general : the
more layers, the more weight a
tire can carry . Tire manufacturers
must also specify the materials
used in the tire . These include
steel, nylon, polyester and other
materials .
@Maximum permitted load
This number indicates the maxi­
mum load in kilograms and
pounds that the tire can carry .
@Uniform ti re quality grade
standards for treadwear,
traction and temperature resistance
Treadwear , traction and tempera­
ture
ranges¢ page 299 .
@ Running direction
The arrows indicate the running
direction of unidirectional tires .
You must always follow the speci- fied running direction
¢
page 319.
@ Maximum permitted
inflation p ressure
Wh eel s
This number indicates the maxi­
mum pressure to which a tire can
be inflated under normal operat­
ing conditions.
Glossary of tire and loading
terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­ matic transmission, power steer­
ing, power brakes, power win ­
dows, power seats, radio, and
heater, to the extent that these
items are available as factory-in­
stalled equipment (whether in­
stalled or not) .
Aspect ratio
means the ratio of the height to
the width of the tire in percent .
Numbers of 55 or lower indicate a
low sidewall for improved steer­
ing response and better overall
handling on dry pavement .
285

Wheels
Bead
means the part of the tire that is
made of steel wires, wrapped or
reinforced by ply cords and that is
shaped to fit the rim .
Bead separation
means a breakdown of the bond
between components in the bead .
Cord
means the strands forming the
plies in the tire .
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manufac­
turer for
a tire of a designated
size that has not been driven for more than a couple of miles (kilo­
meters) at low speeds in the
three hour period before the tire pressure is measured or adjusted .
Curb weight
means the weight of a motor ve­
hicle with standa rd equipment in ­
cluding the maximum ca pacity of
fuel, oil, and coolant, air condi ­
tioning and addit ional weigh t of
optional equipment.
E x tra load tire
means a tire designed to operate
at higher loads and at higher
in -
28 6
flation pressures than t he corre­
spond ing standard tire. Extra load
tires may be identified as "X L",
"xl" , "EXTRA LOAD" , or "RF" on
the sidewall.
Gross Axle Weight Rating ("GAWR")
means the load-car rying capacity
of a single axle system , measu red
at the ti re-ground interfaces .
Gross Vehicle Weight Rating
("GVWR")
means the maximum total loaded
weight of the vehicle .
Groove
means the space between two ad­
jacent tread ribs .
Load rating (code)
means the maximum load tha t a
tire is rated to carry for a given i n­
flation pressure. You may no t find
this informat ion on all ti res be­
cause it is not required by law .
Maximum load rating
means the load rating for a tire at
the maximum permissible infla­
tion pressure for that tire .
Maximum loaded vehicle
weight
means t he sum of:

....
"' -N .... N
-0
0
J: ..
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Ma ximum (permissible }
inflation pres sure
means the maximum cold infla­
tion pressure to which a t ire may
be inflated . Also called "maxi ­
mum inflation pressure."
Normal occupant weight
means 150 l bs. (68 kilograms)
times the number of occupants
seated in the veh icle up to the to­
tal seating capacity of your vehi­
c le.
Occupant distribution
means distribution of occupants
in a vehicle.
Outer diameter
means the overall diameter of an
inflated new tire .
Overall width
means the linear distance be­
tween the exteriors of the side­
walls of an inflated tire, including
elevations due to labeling, deco­
rations, or protective bands or
ribs .
Wheels
Ply
means a layer of rubber-coated
parallel cords .
Production options weight
means the combined weight of
those installed regular production
options weighing over 5 lbs. (2.3 kg) in excess of those standard
items which they replace, not pre ­
viously considered in curb weight
or accessory weight, including heavy duty brakes , ride levelers ,
roof rack, heavy duty battery, and
special trim .
Radial ply tire
means a pneumatic tire in which
the ply cords that extend to the beads are laid at substantially 90
degrees to the centerline of the
tread .
Recommended inflation
pressure
see ~ page 286, Cold tire infla­
tion pressure .
Reinforced tire
means a tire designed to operate
at higher loads and at higher in­
flat ion pressures than the corre­
sponding standard tire. Rein ­
forced tires may be iden tified as
.,.
28 7