2018 AUDI A7 brake

0 0)
-N ,.... N
-0 0) \.) ..
are listed on the safety compli­
ance sticker labe l located on the
driver's side 8 -pillar .
A WAR NING
-
Overloading a vehicle can cause
loss of vehicle contro l, a crash
or other accident, serious per­
sonal injury , and even death .
-Carrying more weight than your vehic le was designed to
carry will p revent the vehicle
from handling properly and increase the risk of the loss of
vehicle control.
-The brakes on a vehicle that has been over loaded may not
be able to stop the veh icle
within a safe dis tance .
-Tires on a vehicle that has been overloaded can fail sud­
d en ly , including a blowout and
sudden deflation, causing loss
of control and a crash .
-Always make su re that the to­
tal load being transported -
includ ing the weight of a trail ­
er hitch and the tongue
we ight of a loaded trailer -
d oes not make t he vehicle
heavier than the vehicle's
Gross Vehicle We ight Rating .
Wheels
Determining correct load
limit
Use the example below to calcu ­
late the total weight of the pas­
sengers and luggage or other
things that you plan to transport
so that you can make sure that
your vehicle will not be overload­
ed .
Steps for Determining Correct
Load Limit
1 . L ocate the statement " THE
COMB INED W EIGH T OF OCCU­
PANTS AND CARGO S HOU LD
NEVER EXCEED XXX KG OR XXX
L BS" on your vehicle's placard
(tire inflation pressure label)
¢ page 215, fig. 189 .
2. Determine the combined
weight of the driver and pas­
sengers that w ill be riding in
your vehicle .
3 . Subtract the combined weight
of the driver and passengers
from
" XXX " kilog rams or " XXX "
pounds shown on the sticker
¢page 215, fig. 189 .
4. T he resulting figure equals the
available amount of cargo and luggage load capacity. For ex­
ample , if the
"XXX " amount
equa ls 1400 lbs . and there
will .,.
219

a co .... N
" N .... 0 00 \.J ' & WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the ca r
was h operator to reduce the risk of acci­
dents.
-T o red uce the risk of cuts, protect yourself
from sha rp metal components when wash­
ing the underbody or the inside of t he wheel
hous ings .
-After wash ing the vehicle, the brak ing effect
may be delayed due to mo isture on the
brake rotors or ice in the w inter . This in­
c reases the risk of an acc ide nt. The bra kes
mus t be d rie d first w ith a few careful brake
app lic at ions.
@ Note
-If yo u wash t he veh icle in an automatic car
wash, yo u m ust retract the rear spoi ler if
necessa ry, and fold the exte rior m irrors i n
to re du ce the risk of damage. Powe r fo ldi ng
ex ter io r m irr ors* m ust only be fo lde d in a nd
o ut u sing t he power folding fu nction .
-
Care and cleaning
-To re duce the risk of pa int damage, do not
was h the vehicle in direct su nlight .
-To re duce the risk of d amage to the s urface,
do not use insect removing sponges, kitche n
sponges or s imilar items .
-Mat te finish painted veh icle components :
-To reduce the risk of damage to t he sur-
face, do not use po lish ing agents o r hard
wax.
-Neve r use protective wax. It can destroy
the matte finish effect .
-Do not place any st ickers or magnetic
s igns on vehicle parts painted w ith matte
finish paint . The paint cou ld be damaged
when the stickers or magne ts are re ­
m oved.
@ For the sake of the environment
Only wash the veh icle in facili ties s pec ia lly de­
s igned for tha t pur pose . This will reduce the
r isk of di rty wate r cont ami nated with o il from
ente rin g t he sewe r sys tem.
Cleaning and care information
When cleani ng and ca ring for in dividua l vehicle
componen ts, re fer to the follow ing tables. The
i nf ormation contained there is s imp ly recom ­
mendations. Fo r qu est ions or for components t
h at are not liste d, co n su lt an au tho riz e d Au di
dealer or au thor ized A udi Se rvice Fa cility. Also
f o llow the information fo und
in ¢ .&. .
Exterior cleaning
Component Situation Solution
Windshield wiper
Deposits Soft cloth with g
lass cleaner, ¢ page 46
blades
Headlights/
Deposi ts So
ft spo nge wi th a m ild soap sol utiona )
Tail lights
Sensors /
Deposits Sensors: soft cloth wit h solvent-free cleaning solut io n
camera lenses Camera le nses: soft cloth w ith a lcoho l- free cleaning so lu -
tion
Snow/ice H
and br ush/solvent-free de -icing spray
Wheels Road salt Water
Bra ke dust Acid-f
ree s pecial clea ning so lution
E xhaust tail pipes Road salt Water, clean ing so lution su itab le for s tainless stee l, if nee-
ess ary
229

a co ,...,
N
" N ,...,
0 00 <.,;) ' Emergency assistance
General information
.. Par k the vehicle as far as poss ible from moving
traff ic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a leve l surface .
It you are on a steep hill, be especially careful.
.. Set the parking brake .
.. Switch the emergency flashe rs on .
.. Set up the warn ing triangle C) page 233 .
.. Have the passengers exit the veh icle . They
sho uld move to a safe place, for example be­
hind a guard rail.
_& WARNING
Follow the s teps given above. This is for your
protection and the for the safety of other d riv­
ers .
Equipment
Warning triangle
App lies to: ve hicles with warning triangle
D
Fig. 193 Luggage compa rtment U d : wa rnin g tr iang le
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
.. Turn the twist lock C) fig . 193 and pull the cover
downward to open the cover.
.. Remove the warning triangle from its holder.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genu ine Accessories program.
Em ergen cy as sis tanc e
Vehicle tool kit
Fig. 194 Lu ggage compartment: vehicle tool kit, tire mob i­
lity kit and comp resso r
The vehicle tool kit, vehicle ja ck*, tire mobility
ki t* and compressor are stored in the luggage
compartment under the ca rgo floor cover .
.. Lift the cargo floor by the p lastic handle .
.. Turn the handle cou nter- clockwise and remove
the cover or the spare tire *.
A WARNING
Improper use of the vehicle jack can cause se­
rious pe rsonal injuries.
-Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if yo u
use the hex head, potentially causing an ac­
cident.
-The factory-supplied jack is intended only
for your vehicle model. Under no circum­ stances shou ld it be used to lift heavy
veh icles o r othe r loads; you risk injuri ng
yourse lf .
-Never start the engine when the vehicle is
raised, which could cause an accident.
-Support the vehicle securely with appropri­
ate stands if wo rk is to be performed under­
neath the vehicle; otherwi se, there is a po­
t ential risk fo r injury .
-Never use the jack supplied with your Aud i
on another vehicle, particularly on a heavier
o n e. Th e jack is o nly sui tab le for u se on the
veh icle i t came wi th.
(D Tips
The vehicle jack* in your vehicle is mainte­
nance-free.
233

Emergency assistance
-If the tire is too severely damaged, see an
authorized Aud i dealer or authorized Aud i
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized Audi
Serv ice Facility for disposal.
(D Tips
Remember to obtain a new bottle of sealant
from an authorized Audi dealer or authorized
Audi Serv ice Facility after repairing a tire.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.,. After you exper ience a tire fa ilure, pull the car
well away from moving traff ic and try to reach
level ground
before you stop ¢.&, .
.,. All passengers sho uld leave the car and move
to a safe location (for instance, be hind t he
guardrail) ¢.&, .
.. Engage the parking brake to prevent your vehi­
cle from rolling
unintentionally ¢.&, .
.. Move selector lever to position P ¢ A-
.. If you are towing a trailer, unhitch the trailer
from your veh icle .
.,. Take the jack and the spare tire* out of the lug­
gage compartment
ca> page 233 .
.8, WARNING
You or your passengers could be inju red w hile
chan gin g a wheel if you do not follow these
safety precautions:
- If you have a flat ti re, move a safe d ista nee
off th e road. Turn off the engine, turn the
emergency flashers on and use other warn ­
ing devices to alert other motorists .
- Make sur e that passengers wait in a safe
place away from the vehicle and we ll away
from the road and traffic.
236
- To help prevent the vehicle from moving
suddenly and possibly s lipping off the jack,
always fully set the parking brake and block
the front and back of the wheel diagonally
opposite the wheel being changed. When
one front wheel is lifted off the ground,
p lacing the Automat ic Transmission in P
(Pa rk) w ill
not prevent the vehicle from
mov ing.
- Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the lu ggage com ­
pa rtment
¢page 134 .
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
trols for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack
ca> page 238 .
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order .
1. Act ivate the vehicle jack mode* ca> page 238 .
2. Remove the decorative wheel cover* or the
wheel bolt caps*. For more details see also
¢ page 23 7, Decorative wheel covers or
¢ page 237, Wheels with wheel bolt caps.
3. Loosen the wheel bolts ¢ page 238.
4. Locate the proper mounting point for the
jack and alig n the jack below that po int
¢ page 238 .
5. Raise the car with the jack ca> page 238.
6. Remove the wheel with the flat tire and then
install
the spare ca> page 240.
7. T ighten all whee l bolts lightly.
8 .
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten
all wheel
bolts ¢ page 238.
10. Replace the decorat ive wheel cover* or the
wheel bolt caps*.
11. Deact ivate the vehicle jack mode* in the
MM I:
ICARI function button > (Ca r)* systems .,.

Emergency assistance
The caps are to protect and keep the whee l bolts
clean.
Loosening and tightening the wheel bolts
Th e wheel bolts must be loosened b efore raising
the vehicle.
F ig . 2 00 Cha ngin g a w hee l: l oosening t he w heel bol ts
Loosening
.,. Slide the wheel wrench onto the wheel bolt as
far as it w ill go .
.,. Take t ight hold of the end of the wrench handle
and t urn the whee l bolts
counter -clockwise
about one single t ur n in t he d irec tion of ar row
¢ fig . 200.
Tightening
.,. Slide the wheel wrench onto the wheel bolt as
far as it w ill go .
.,. Take t igh t hold of the end of the wrench handle
and tu rn ea ch whee l bolt
clockwi se u ntil it is
sea ted.
_& WARNING
- Do not u se force or hurry when changing a
whee l
-you can ca use the vehicle to s lip off
th e jac k and cause serious pe rsonal injur ies .
-Do not loosen the whee l bolts more than
one turn
before you raise the vehicle with
t h e jac k.
-You risk an i njury.
(D Tips
- N ever use the he xag onal socket in the han­
dle of the screwd river to loosen o r tighten
the w heel bolts .
- If a whee l bolt is very tigh t, you m ay fi nd i t
eas ier to loosen by carefully pus hing down
238
on the end of the whee l bolt wrench with
one foot only. As you do so, ho ld on to the
car to keep your balance and ta ke care not
to slip .
Raising the vehicle
The vehicle must be lifted with the jack first be­
fore the wheel can be removed.
Fig . 201 Sill pa nels: marki ngs
.,, ..,
0
---"rn; S!~~;::---~
Fig. 20 2 S ill: p osit io nin g the ve hicle jack
.,. Ac tiva te the veh icle jack mo de* in the MMI:
!CAR I function button> (Car )* systems cont rol
but ton >
Servicing & che cks > Air su sp .: jack
mode > On .
.,. Engage the parking brake to prevent your veh i­
cle from rolling uninte ntionally .
.,. Move the selector lever to position P .
.,. Find the marking (imprint) on the sill that is
nea rest the w heel that will be changed
¢ fig. 201 . Behind the marking, there is a lift­
ing point
on t he sill fo r the ve hicle jack .
.,. Applies to: vehicles with a s ill: Remove the cov­
er fro m the sill before lifting the vehicle wi th a
veh icle
ja ck¢ page 239.
.,. Tur n the vehicle jack located un der the lifting
point o n the s ill to raise the jack unt il its
arm @
~ fig. 202 is locate d under the d esignated plas-
tic
mount ¢ .&,¢(D. II>

Emergency assistance
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig. 204 Changing a wheel: using the screw driver handl e
(wit h th e blade re m oved) to turn the bol ts
F ig . 205 Changing a wheel: alignment p in inside t he top
hole
Afte r you have loosened a ll w heel bo lts and
raised t he vehi cle off the ground, remove and re­
p lace the whee l as fo llows:
Removing the wheel
• U se the hexagonal so cket in the screwdriver
handle
t o comple tely remove the topmost
whee l bolt and set it aside on a
clean surfa ce
¢ fig. 204 .
• Screw the th readed end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole¢ fig. 2051> .
• Then remove the other wheel bolts as described
above.
• Takeoff th e wheel leav ing the a lignment pin in
the bo lt ho le
¢ 0 .
l) Applies to vehicles with ceram ic brake rotors*: Use a sec­
ond alignment
pin* (stored in th e spa re whee l well mo ld­
ing) for the lower ho le, fo llowing t he descr iption for the
first alignment pin .
240
Putting on the spare wheel
• Lif t the sp are whee l and caref ully slide it over
t he alignment p in to guide it in place
¢ (D .
• Use the hexagonal socket in the sc rewdr iver
ha nd le to screw in and tighten a ll w heel bolts
slightly.
• Remove the alignment pin and insert and t ight­
en the remaining w heel bo lt slight ly like the
rest.
• Tu rn the jack hand le co unte r-clockw ise to lowe r
t he vehicle unt il t he jac k is f ully re leased.
• Use the w heel bo lt wren ch to tighten a ll wheel
bolts fi rm ly¢
p age 238. Tighten them cross­
wise,
from one bo lt to the (a pprox imately) op ­
posite one, to keep the whee l centered.
([» Note
When remov ing o r installin g the wheel, the
rim co uld hit the brake rotor/ce ramic brake
r otor * and damage t he rotor . Work carefully
and have a second person he lp you.
(D Tips
N eve r use the he xagonal socket in the han dle
of the sc rew drive r to loosen or t ig hten the
whee l bolts.
- Pull the reversible blade from the screwdr iv­
er before yo u use t he hexagona l soc ket in
t h e handle to t urn the whee l bolts.
- When mounti ng tires with
unidirectional
tread design
make sure the tread pattern is
pointed the right
way¢ page 241.
- The wheel bolts sho uld be clean and easy to
t u rn. Check fo r dirt and corrosion on the
mating surfaces of both the wheel and t he
hub. Remove all d irt from these s urfaces be­
fore remounti ng the whee l.

Fuses
Driver side cockpit fuse
assignment
Fig. 208 Driver side cockpit: fuse panel with plastic bracket
Fuse panel @ (black)
No. Equipment
Electromechanical power steering, trailer
1 hitch, ionizer, switch strip, seat heating
(rear), electromechanical parking brake
Horn, climate control system, Gateway,
2 automatic
dimming interior rearv iew mi r-
ror, On-Board Unit
4 Park ing aid, headlight range adjustment
5 Dynamic steering, electronic stabilization
control (E5C)
6 Headlights
7 Adaptive cruise control
8 Front passenger's seat sensors, airbag
9 Gateway
10 Engine sound, night vision
assist, garage
door opener (Home link), parking aid
11 Video
camera image processing
12 Headlights
13 Steering column switch module
244
Fuse panel
@ (black)
14 Terminal 15 (luggage compartment)
15 Starter
Fuse panel @ (brown)
N o. Equipment
1 Infotainment system
2 Infotainment system
3 F
ron t passenger's seat
5 Airbag, electronic stabilizat
ion control
(ESC)
6 Anti-theft alarm system
7 Electromechanical parking brake
8 Inter
ior lights
9
Windshield video camera heating, light/
rain sensor
10 Lumbar support (dr iver's seat)
11 Driver's
seat
12 Electronic stabilization control
13 Horn
14 Headlights
15 F
ront seat heating
16 Dynamic steering
Fuse panel © (red)
No . Equipment
1 Clutch pedal
2 Fuel pump
3 Brake light sensor
4 Engin e acoustics
5 Rear door
6 Front
door
7 Electronic stabilizat ion control
8 Windshield wiper motor
9 Headlight washer system
10 Inter
ior lighting, climate control system
11 Headlights
12 Sunroof

a co ,...,
N
" N ,...,
0 00 <.:l ' Front passenger side
cockpit fuse assignment
F ig. 2 09 Front passenger side cockpit: f use pane l w it h
p las tic bracket
Fuse panel @ (red )
No . Equipment
1 Infotainment, CD changer
2 I nfotainment (disp lay)
Fuse panel @ (brown )
No . Equipment
1 Climate control system
2 Climate con
trol sy stem (blowe r)
3 Diagnostic interface
4 Ele ctrical ignit ion lo ck
5 Electronic steer ing column lock
6 S teer ing col umn sw itch modu le
7 Power steering column adjustment
8 Light swi tch
9 Head-up display
1 0 I
nst rument cluste r
1 1 Infotainment, DVD changer
Fuses
Luggage compartment
fuse assignment
F ig . 2 10 L uggage compa rtment: fuse pane l with p last ic
b racket
Fuse panel @ (black )
No . Equipment
1 Tra
ile r hitc h/220 volt soc ket
2 Tra ile r hi tc h /climati ze d cup holder
3
Tra iler hitc h/ad justing front passenger's
seat from the rear
4 El ec trome chanic al pa rking brake
s Electromec hanical parking brake
6 F ront door (fron t passenger's si de)
7 Rear exterior lighting
8 Cen tral locking, closi ng aid
9 Seat heating (front)
1 1 Seat heating (rear), c
limate control system
12 Tra ile r hitch
Fuse panel @ (red)
No . Equipment
1 Left safety belt tensioner
2 R igh t safety be lt te nsion er
3 F u el pump
4 En gine moun t (gasoline e ngine)
s
Sensor-controlled l uggage compa rtment
lid
6 A ir su sp ension, ad ap tive d am pers
7 Rear door (front passenger's side)
8 Tail lights
9 Luggage compartment lid
10 Rear sea t ente rtainmen t
12 Rear spoiler (Spo rtback), sunroof
245