2018 AUDI A7 engine oil

a co .... N
" N .... 0 00 \.J ' intervals and ensures a better reaction time for
the brakes in wet weather.
The braking effect can also be reduced if you are
driving on salted roads and you do not apply the
brakes for long periods of time. The layer of salt
on the brake rotors and pads must be worn off
first when the brakes are applied.
Due to its surface, the ceramic brake rotor* ab­
sorbs moisture in certain situations. Therefore,
there will temporarily be less braking force than
when the brakes are dry. You can compensate for
this by pressing the brake pedal harder.
Corrosion
Leaving the vehicle parked for long periods of
time, low mileage and avoiding heavy braking
can contribute to corrosion on the brake rotors
and to dirty brake pads.
If you usually avoid heavy braking or if there is
corrosion present, occasional heavy braking at
high speeds is recommended to clean the brake
rotors and
pads ¢.&. .
Brake system malfunction
If you notice that the brake pedal travel has sud­
denly increased, then a brake circuit in the dual­
circuit brake system may have malfunctioned. Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
problem corrected. On the way there, drive with
reduced speed and keep in mind that you will
need a longer distance to stop and you will need
to press the brake pedal harder .
Low brake fluid level
When the brake fluid level is low, malfunctions in
the brake system may occur . The brake fluid level
is electronically monitored .
Brake booster
The brake booster amplifies the pressure you ap­
ply to the brake pedal. It only works when the en­
gine is running.
A WARNING
-Only apply the brakes for the purpose of
cleaning the brake system when road and
-
Intelligent Technology
traffic conditions permit. You must not en­
danger other road users. This increases the
risk of an accident.
- Never let the vehicle roll while the engine is
stopped because this increases the risk of an
accident.
- New brake pads do not achieve their full
braking effect during the first 250 mi
(400 km) . They must be "broken in" first.
The break-in period can be considerably lon­
ger for vehicles with ceramic brake rotors*.
However, you can compensate for the
slightly reduced braking force by pressing
firmly on the brake pedal. Avoid heavy brak­
ing during the break-in period.
- Certain weather and operating conditions
such as driving through water, driving in
heavy rain or driving after washing your ve­
hicle can impair the effectiveness of the
brakes. In the winter, ice may build up on
the brake pads, rotors and drums. Check
these components by braking carefully. Ap­
plying the brakes carefully several times
dries the brakes and removes ice build-up .
- The efficiency of the brakes can also be im­
paired by driving for long stretches on roads
covered with salt without using the brakes.
You can remove salt deposits from the
brake rotors and pads by carefully applying
the brakes several times.
- If the front spoiler is damaged or you install
another spoiler, make sure the front wheel
brakes are ventilated properly. Otherwise,
the brake system could overheat, which re­
duces their effectiveness.
- Failure of a brake circuit impairs braking
performance, which increases braking dis­
tance. Avoid driving the vehicle and have it
towed it to the nearest authorized Audi
dealer or authorized Audi Service Facility.
- If the brake booster is not working, you will
have to press much harder on the brake
pedal to compensate for the lack of the
booster .
@ Note
-Never let the brakes "rub" by pressing the
pedal lightly when braking is not actually
123

Intellig ent T echn olo gy
necessary. This causes the brakes to over­
heat and increases braking distance and
causes wear.
- Before driving downhi ll a long distance on a
steep hill, decrease your speed and select a l ower gear. This makes use of the engine
braking effect and relieves the brakes. If
you need to brake additionally, brake in in­
tervals and not continuously .
(D Tips
-If the brake booster is not working, you
must press the brake pedal with much more
force than normal.
- If you retrofit your vehicle with a front spoil­
er, wheel covers or s imilar items, make sure
that the a ir flow to the front wheels is not
i nterrupted. Otherw ise the brake system
ca n become too hot.
Electromechanical
steering, dynamic
steering
The electromechanical steering supports the
driver's steering movements .
Power steering adapts electronically based on
the vehicle speed .
Indicator light s and me ssages
• Do not d rive vehicle: St eering d efecti ve
If t his ind icator light tu rns o n and stays o n and
this message appears, t he power steer ing may
have fai led.
Stop the veh icle in a safe locat io n as soon as pos­
sib le. Do
n ot continue dr iving. See an author ized
Aud i dea ler or authorized Aud i Serv ice Facility for
assistance.
l;:r-ij St ee ring : Sys tem f ault You can con tinu e
dri ving
If the ind icator light turns on and the message
appears, the steering wheel may be more diff i­
cult to move or mo re sensit ive tha n usual. The
steer ing whee l may a lso be at an angle when
driving straight .
124
Drive slowly to an authorized Audi dea ler or au­
thorized Audi Service Facility to have the mal ­
funct ion corrected .
'I-ij Dyn ami c ste ering : Initializing
If the indicator l ight is blinking and this message
appears, dy namic stee ring* is be ing initialized.
The steer ing whee l will be easy to move afte r
start ing t he engine . Re -init ialization mig ht be
necessary if the steering wheel was moved hard
to the left and right while the vehicle was not
moving . The d isp lay turns off if the init ia li zation
was successful.
(D Tips
- If the . or 'Tfl indicator light only stays on
for a short time, you may cont inue driving .
- Th e dynamic steering stability systems
<=>page 120 are not avai lab le in the event of
a system malfunction.
- For additiona l information on dynamic
steering, see
<=> page 105.
All wheel drive (quattro)
Applies to: vehicles with all wheel drive
In all wheel drive, all four wheels are powered.
G en eral information
In all whee l dr ive, the dr iv ing power is divided be ­
tween all four whee ls. This happens automatical­
l y depending on your driving behavior as we ll as
the current road conditions . Also see
c> page 120, Electronic stabili zation control
(ESC).
A center differential distributes the driving power
variab ly to the front and rear ax le. It works to­
gether w ith selective whee l torque contro l, wh ich
activates when driving through curves
<=>page 120 . With the sport d ifferent ial*, power
distribution to the rear wheels is variable and can
be adjusted with d rive select
c> page 105 .
The all wheel drive concept is designed for high
engine power . Your vehicle is except ionally pow­
erful and has excellent driving characteristics
both under normal driving conditions and on
snow and ice. A lways read and follow safety pre-
ca utions
c> .&. . II>-

Intellig ent T echn olo gy
A WARNING
When extending and retracting the rear spoil­
er, make sure there are no persons or objects
w ith in the spoiler range to reduce the risk of
injury .
A WARNING -
Driv ing at higher speeds w ithout the rear
spoiler dep loyed can impa ir hand ling cha rac­
ter istics, mak ing the veh icle h arder to con­
trol.
- Always make sure that the spoiler is de ­
ployed whe n driving at speeds ove r 85 mp h
(140 km/h) . If the rear spoiler warning/indi ­
cator lig ht in the instrument cluster comes
on, the rear spoi ler may not have deployed.
- Never drive at speeds higher than 85 mph
(140 km/h) if the spoiler is not deployed .
Have the spoiler inspected as soon as possi­
ble by an author iz ed Audi dealer or qualif ied
workshop.
- Always obey speed limits and other traffic
laws .
@ Note
-Never push on the vehicle on the rear spoi l­
er . T his cou ld cause damage.
- To prevent damage to the rear spoiler do not lean or p lace anyt hing on it.
- Only operate t he rear spoiler manually when
the luggage compartment lid is close and
the rear spoiler moving parts are not
blocked. Otherwise, damage could occur.
(D Tips
Clean the rear spoi ler compartment every 2 to
3 months . To function correctly, the rear
spoiler must be free of ice, snow and leaves.
126
Energy management
The starting ability is optimized
T he energy management sys tem manages the
electrical energy distribution and optimizes the
availability of electrical energy for starting the
engine.
When a vehicle with a conventional energy sys ­
tem is not driven for a long time, the veh icle bat­
tery is drained by equ ipment (for example, the
i mmob il izer). I n certa in circumstances, there
could may not be enough energy to start the en ­
gine.
Your vehicle is equipped with an intell igent ener­
gy management system fo r dist ributing elect rici­
ty. Thi s sign if icantly improves the start ing ab il ity
and increases the vehicle battery life .
The energy management system Is made up of
battery dia gno sis , idling current management ,
and dynamic energ y m ana gement .
Battery di agnosis
T he battery diagnos is determines the vehicle bat ­
tery cha rge level. The sensors detect the batte ry,
t h e battery cur rent, and the battery temperature .
The current cha rge level and the pe rformance of
t h e ve hicle battery are dete rm ined based on th is.
Idling current management
The idling current management decreases the
energy used while parked . With the engine
switched off , it ma nages the ene rgy distr ib ution
to the d ifferent e lectr ica l components . Data from
t h e battery d iagnosis is ta ken into a ccou nt for
t hi s.
Depend ing on the vehicle batte ry cha rge level,
electr ical eq uipme nt is switched off one item af ­
te r th e o ther to p revent the veh icle bat tery from
dra ining and to ma intain the starting ab ility.
Dynamic energy manag ement
While driv ing , dynam ic energy management dis­
t ributes the app ropr iate amo unt of energy to t he
electr ical eq uipme nt.
It contro ls the batte ry
c h arge level so tha t the amount of energy is no t
..,.

Checking and Filling
belt, alternator and radiator fan) and from
the high-voltage ignition system.
- Do not under any circumstances give gas in­
advertently (for example, by hand from the
engine compartment) if the vehicle is sta­
tionary but the engine is running and a gear
is engaged. Otherwise, the vehicle will start
to move immediately and this could result
in an accident.
- Pay attention to the following warnings list­
ed when work on the fuel system or on the
electrical equipment is required.
- Do not smoke.
- Never work near open flames.
- Always have a working fire extinguisher
nearby.
- All work on the battery or electrical system
in your vehicle can result in injuries, chemi­
cal burns, accidents or burns. Because of
this, all work must be performed
only by an
authorized Audi dealer or authorized Audi
Service Facility.
- To reduce the risk of electric shock and in­
jury, never touch the following components when the engine is running or is being start­
ed:
- Ignition cable
- Other components in the electronic high-
voltage ignition system
- If you must check or perform work on the
engine while it is running:
- Set the parking brake and place the selec­ tor lever in the P (park) position first.
- Always proceed with extreme caution so that clothing, jewelry or long hair do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compo­
nents. Tie back long hair before beginning
work and do not wear clothing that can
hang down into the engine.
- Limit your exposure to exhaust and chemi­
cals to as short a time as
possible~ &..
A WARNING
California Proposition 6S Warning:
194
-Engine exhaust, some of its constituents,
and certain vehicle components contain or
emit chemicals known to the State of Cali­
fornia to cause cancer and birth defects and
reproductive harm . In addition, certain flu­
ids contained in vehicles and certain prod­
ucts of component wear contain or emit
chemicals known to the State of California
to cause cancer and birth defects or other
reproductive harm.
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive harms.
Wash hands after handling.
@ Note
When filling fluids, be sure not to mix the flu­
ids up. Otherwise severe malfunctions and en­
gine damage will occur.
@ For the sake of the environment
You should regularly check the ground under
your vehicle in order to detect leaks quickly. If there are visible spots from oil or other fluids, bring your vehicle to an authorized Audi deal­
er or authorized Audi Service Facility to be
checked.

Checking and Filling
Engine compartment overview
The most important check points.
Fig. 181 Typical location of the rese rvoir and the engine o il filler open ing
(D Jump start po int(-) with hex head screw
~ page 202, ¢page 247
@ Jump start point(+) under the cover
~page 202, ¢page 247
® Engine oil label* w ith VW standard
¢ page 196
@ Brake fluid reservoir ((0)) ¢ page 201
® Engine oil filler opening(~)¢ page 198
@ Coolant reservoir (- L) ~ page 200
(j) Washer fluid reservoir (0) ¢ page 203
The engine oil fill er opening ® may be located in
a different area depending on the specific engine.
& WARNING
Read and follow all WARNINGS before check­
ing anything in the engine
compartment¢ &
in Working in the engine compartment on
page 193.
196
Engine oil
If the engine oil level is too low
If you need to add engine oil, use an oil that is
listed on the sticker.
The sticker is located at the
front of the eng ine
compartment¢ page 196,
fig . 181 .
If the recommended engine o il is not availab le,
in an emergency you may add a maximum of 1
quart(! liter) of ACEA C3 or API SN eng ine oi l
one time until the next oil change .
For more information on the correct eng ine oil
for your vehicle, contact an authorized Audi deal­
er or authorized Aud i Serv ice Facility . Have the oil
c h anged by an authorized Audi dealer or author­
i zed Service Facility.

a co .... N
" N .... 0 00 \,;J ' Audi rec ommends
~ Castrot /lftlg;'f.E@t Frtrrr.::--.~lri,'lAl.
A ud i recomm ends using the Lo ng Life h igh ­
perfo rm ance eng ine oil from Aud i Genu ine
Parts .
Checking the engine oil level
The engine oil level can be checked in the Info­
tainment system
Observe the safety precautions¢ A in Working
in the engine compartment on page 193.
~ Park your vehicle on a level surface.
~ Shut the engine off when it is warm.
~ Switch only the ignition back on.
~ Wait approx imately two minutes.
~ Select: the ICARI function button > ( C ar)* Sys ­
tem s
control button > Service & control > O il
l e v el.
~ Read the o il level in the I nfota inme nt system.
Add eng ine oil if the ba r in the oil leve l ind ica ­
tor is just before
"min"¢ page 198.
(UJ) Note
The engine oil leve l mus t not be unde r the
"min" mark ing, as this will increase the risk of
engine damage.
(D Tips
The o il level indica tor in the disp lay is on ly an
informationa l display. If the o il level is too
low, a minimum oi l warning appears in the in ­
strument cluster. Add oil and close the hood.
The current oil level is d isplayed in the Info­
tainment system the next t ime the ignition is
sw itched on.
(D Tips
The engine oil consumption may be up to
0.5 quart/600 m iles (0.S liter/1,000 km), de­
pending on driving style and operating condi­
tions. In RS models, the o il consumption may
be up to 1 qt/600 mi (0 .8 l/ 1,000 km). Con­
sumpt io n may be h igher du ring the first
3,00 0 miles (5, 000 km). Be cause of this, the
eng ine o il level must be checked reg ularly. It
Ch eck ing and F illing
is best to check each time you refue l yo ur ve ­
hicle and before long drives.
- In order to p rov ide effective lubrication and
cooling of interna l engine components, a ll
internal comb ustion engines consume acer ­
tain amount of oil. Oi l consumption var ies
from engine to engine and may change sig­ nifica ntly over the life of the engine. Typi­
cally, eng ines with a specif ied break-in peri­
od consume more o il du ring the break-in pe­
r iod than they consume afte r oil cons ump­
tion has stabilized.
- Under norma l condit ions, the rate of oil
c ons umption depends on the q ual ity and
vis cos ity of the oil, the R PM (revo lutions per
m in ute) a t which the engine is operated, the
ambient temperature and road conditions .
Furt her factors are the amount of oi l di lu­
tion from water condensat ion or fue l resi ­
due and the oxidation level of the oil. As any
eng ine is subject to wear as m ileage builds
up, the oil consumption may increase over
t ime until replacement of worn components
may become necessa ry.
- With all these var iables com ing into play,
no sta ndard rate of o il consumption can be
established o r specified. There is no a lter na­
ti ve to c hec king the oil leve l reg ula rly and
frequently.
- If you have the impress ion your engine co n­
sumes excessive amo unts of o il, we recom ­
mend that yo u consult an author ized A udi
dea ler to have the cause of your concern
properly diagnosed . Keep in mind that the
accurate measurement of o il consumption
requires great care and may take some
time. An authorized Aud i dealer has instruc­
tions about how to measure o il consump­
tion accurately.
- You can find informat ion on engine oil and
eng ine o il capacit ies for the USA at
www .aud i usa .com/he lp/ma intenance, o r
for Ca nada at www.aud i.ca/ca/web/en/
cu stomer -area/ ca re -and -m a i ntena nee/ au di­
serv i ce -sched u les. htm l, or ca ll
800 -8 22-2834 .
197

Check ing and F illing
Adding engine oil
F ig. 182 Engine co mpartment : en gin e oil fille r opening
cove r
Observe the safety precaut ions ¢&. in Working
in the engine comportment on page
193 .
"'Turn the eng ine off.
"' Open the hood ¢ page 195.
"'Unscrew the cap~ for the eng ine oi l filler
opening
¢ fig. 182.
"'Carefu lly add 0.5 quart (0 .5 liter) of the correct
oi l
¢pag e 196.
"'Close the engine oil filler opening cap .
"'Close the engine compartment lid.
"'Restart the ign ition after two mi nutes and read
the current o il level in the Infotainment system
¢ page 197 , Checking the engine oil level .
"'Add more oil if necessa ry .
,& WARNING
- Whe n add ing o il, do not let oil d rip onto hot
engine components . This increases the r is k
of a fire.
- Yo u m ust seal the cap on the oil fi lle r open ­
ing correctly so that oil does not leak o ut
onto the hot engine and exhaust system
when the eng ine is r unning, because this is
a fire hazard.
- Always clean skin thorough ly if it comes into
contact with engine oil.
- Engine oil is poisono us and must be kept
o ut of reach of chi ld ren.
- Store the engine oi l sec urely in the original
container.
(LlJ) Note
- If the message Ill Oil l evel i s too full.
Plea se redu ce oil le vel.
appears, there is too
198
much oil in the engine and the re is a r isk o f
cata lytic converter and engine damage. Do
not start t he engine. Contact an autho rized
Audi dealer or author ized Audi Service Fa­
cility to have excess eng ine o il extracted if
necessary .
- Your L imited New Vehicle Warranty does
not cover damage or ma lfunctions due to
failure to follow recommended mai nte­
nance and use requ irements as set fort h in
the A udi Owne r's Manual and War ranty
&
Ma inte nan ce bookle t.
- Use on ly a high quality engine o il that ex­
press ly complies with the A ud i oi l quality
s ta ndard spec ified fo r yo ur vehicle 's eng ine.
Us ing any othe r oi l c an cause ser io us eng ine
damage .
- Do not mix any add it io na l lubr ic a nts in to
t he engine oil. Damage ca used by such add i­
tives is not covered by the warranty .
@ For the sake of the environment
- Oil sho uld neve r en ter the sewer sys tem or
come in to contact with the g round .
- Pay attent ion to lega l re quir emen ts when
disposing o f emp ty o il conta iners.
Changing the engine oil
We recommend that hove your oil changed by on
authorized Audi dealer or a qualified servi ce sta ­
tion.
Befo re yo u check anything in t he engine compart ­
ment,
alway s read and h eed all WARNINGS ¢ &
in Working in the engine comportment on
page
193.
The eng ine o il must be changed according to the
i nte rvals spec ified in yo ur War ranty
& Ma inte ­
nance boo klet. This is ve ry important because the
l ubricating prope rties of oil diminish gradua lly
during norma l vehicle us e.
Un der some c ircumstances the engine oil should
be c hanged more freq uent ly. Change oi l more of ­
ten if you drive mostly s hort distances, operate
the ve hicle in dusty areas or under
predominantly ..,.

a co .... N
" N .... 0 00 \,;J ' stop-and-go traffic conditions, or have your vehi­
cle where temperatures remain below freezing
for extended periods.
Detergent additives in the oil will make fresh oil
l ook dark after the engine has been running for a
short time. This is norma l and is not a reason to
change the oil more often than recommended.
Because of the problem of proper disposa l, along
with the special tools and necessary expertise re­
quired, we strong ly recommend that you have
your oil changed by an authorized
Audi dealer or
a qualified service station .
If you choose to change your oil yourself, please
note the following important information:
A WARNING
To reduce the risk of personal injury if you
must change the engine oil in your veh icle
yourself:
- Wear eye protection.
- To reduce the risk of burns from hot engine
o il, let the eng ine cool down to the touch.
-
-When removing the oil drain plug with your
fingers, stay as far away as possible. Always
keep your forearm parallel to the ground to
help prevent hot oil from running down your
arm.
- Drain the oil into a container designed for
this purpose, one large enough to hold at
least the total amount of oil in your engine .
- Engine oil is poisonous. Keep it well out of
the reach of children.
- Cont inuous contact w ith used engine oil is
harmful to your sk in. Always protect your
sk in by washing oil off thoroughly w ith soap
and water.
@ Note
Never mix oil addit ives with your engine o il.
These additives can damage your eng ine and
adversely affect your Audi Limited New Vehi­
cle Warranty.
Checking and Filling
@) For the sake of the environment
-Before changing your oi l, first make sure
you know where you can properly dispose of
the used oil.
- Always dispose of used engine oi l properly.
Do not dump it on garden soil, wooded
areas, into open streams or down sewage
drains.
- Recycle used engine o il by tak ing it to a used
eng ine oil collection fac ility in your area, or
contact a service station .
Cooling system
Coolant
The engine cooling system is filled wit h a mixture
of purified water and coolant additive at the fac ­
tory. This coolant must not be not changed.
T he coolant level is monitored through
the . in­
dicator light
r=;, page 14. However, we do recom­
mend occasionally checking the coolant leve l
manua lly.
If you must add coolant, use a mixture of water
and coolant additive. Mixing the coo lant additive
with distilled water is recommended.
Coolant additive
The coolant additive is made of anti-freezing and
corrosion protection agents. Only use the follow­
ing coolant additives. These additives may be
mixed with each other .
Coolant additive Specification
Gl2evo
TL 774 L
Gl2++ TL 774 G
Gl3 TL 774
J
The amount of coolant additive that needs to be
mixed with water depends on the climate where
the vehicle wi ll be operated .
If the coolant addi ­
tive percentage is too low, the coolant can freeze
and damage the engine.
.,.
199