2018 AUDI A6 wheel

a co .... N
" N .... 0 0 \,;J ' (D Tips
You can also use all season tires instead of
winter tires . Please note that in some coun­
tries where winter tires are required, only
winter tires with
the ~ symbol may be per­
mitted.
Snow chains
Snow chains not only improve the driving in win­
ter road conditions, but also the braking .
.. Only install snow chains on the front wheels.
This applies also to vehicles with all wheel
drive* .
.. Check and correct the seating of the snow
chains after dr iv in g a few feet, if necessary . Fol­
low the instructions from the manufacturer .
.. Note the maximum speed of 30 mph (SO km/
h). Note the loca l regulations.
Use of snow chains is only perm itted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi dealer or author ­
ized Audi Service
Facility to see if you may use
snow chains.
You must remove the snow chains on roads with­
out snow. Otherwise, you could impair driving
ability and damage the tires.
A WARNING
Using incorrect snow chains or installing snow
chains incorrectly can result in loss of vehicle
control, which increases the risk of an acci­
dent .
{[J) Note
- Snow chains can damage the rims/wheel
covers* if the chains come into direct con­
tact with them . Remove the wheel covers*
first . Use coated snow chains.
- Using snow chains that add more than 0.4
inch (10.5 mm) of height can severely dam­
age the wheel housings and other vehicle
components.
- Do not install and use snow chains if there is
a malfunction in the air suspension*, be­
cause the vehicle height will be very low. If
Wheels
you drive with snow chains anyway, the
wheel housings and other vehicle compo­
nents can be severely damaged.
(D Tips
When using snow chains, it may be useful to
switch on sport
mode¢ page 120.
Low-profile tires
Applies to: vehicles with low-profile tires
Compared to other tire/rim combinations, low­
profile tires offer a wider tread surface and a
larger rim diameter with shorter tire sidewalls.
This results in an agile driving style . However, it
may reduce the level of comfort and increase
road noise when driving on roads in poor condi­
tion.
Low -profile tires can become damaged more
quickly than standard tires when driving over
large bumps, potholes, manhole covers , and
curbs . Therefore, it is particularly important to
maintain the correct tir e pressure
¢ page 211.
To reduce the risk of damage to the tires and
rims, drive very carefully on poor roads.
Check your wheels regularly every 2,000 mi
(3,000 km) for damage . For example, check for
bulges/cracks on the tires or deformations/
cracks on the rims.
After a heavy impact or damage, have the tires
and rims inspected or replaced immediately by
an authorized Audi dealer or authorized Audi
Service Facility.
Low-profile tires can wear out faster than stand­
ard tires .
Uniform tire quality grading
-Tread wear
- Traction AA ABC
- Temperature ABC
Quality grades can be found where applicable on
the tire side wall between tread shoulder and maximum section width
¢ page 202, fig. 185 .
217

Wheels
For example: Tr ead wea r 200, Traction AA, Tem ­
pe rature
A .
All passenge r ca r tires m ust conform to Federa l
Safety Requi rements in addition to these g rades.
Tread wear
The tread wear grade is a comparat ive rat ing
based on the wear rate of the t ire when tested
unde r contro ll ed conditions o n a specified gov ­
e rnmen t test co urse.
For example, a tire graded 150 would wear one
and one ha lf ( 11/2) t imes as well on the gove rn­
ment course as a tire g raded 1 00.
The relative performance of t ires depends upon
the actual condi tions of their use, howeve r, and
may depart s ignificant ly from the norm d ue to
va ria tions in driving hab its, service pra ctices and
d ifferences in road ch aract eris tics and clim ate.
Traction
The traction grades, from highest to lowest, are
AA, A, Band
C. T hose grades represent the t ire's
ab ility to stop on wet pavement as meas ured un­
de r contro lled condi tions o n specified gove rn ­
men t tes t su rfa ces of asp ha lt and conc re te. A tire
mar ked C m ay have poor trac tion pe rforma nce
q _&. ,
Temperature
The temperature grades a re A (t he highest), B,
and C, rep resent ing the tire' s resistan ce to t he
gener ation o f heat and it s abili ty to d iss ipate
heat when tested unde r controlled condi tions on
a specified in door laboratory test whee l.
Susta ined hig h tem perature can cause t he ma te ­
r ial of the t ire to dege nerate and re duce tire life,
an d excess ive temperatu re can lead to sudden
tire fai lure
q .&. .
The gr ade C co rresponds to a leve l of perfor m­
a nce wh ich all passenge r car tir es mus t mee t un ­
der t he Fede ra l Mo tor Vehicle Safety Standar d
No . 109 . Grades Band A represent higher leve ls
of perfo rmance on the labo rato ry test w heel than
the min imum required by law.
218
A WARNING -
The tract io n grade assigned to this t ire is
based on straight-a head braking traction
tes ts, a nd does no t in clude acceleration, cor­
ne ring, hy droplaning or pea k traction cha rac­
teris tics.
A WARNING
The tem perat ure grade fo r thi s tire is estab­
lishe d fo r a t ire th at is p roperl y infl ated and
n ot overloaded . Excessive s peed, under infla ­
tion, o r excessive loa ding, either separate ly or
i n comb inat io n, can cause heat bu ildup and
possib le t ire fai lure.
A WARNING
-
-
Tempe rature grades app ly to t ires that are
proper ly inflated a nd not over or under inflat­
ed .
Tire pressure monitoring
system
ill General notes
Each tire, including the spare (if prov ided),
shou ld be checked monthly when cold and inflat­
ed to the i nflat ion press ure recommended by the
vehicle manufacture r on the veh icle placard or
ti re infla tion p ressure labe l. (If your ve hicle has
t ir es of a diffe rent size t han the si ze ind icated on
t h e ve hicle placard or tire i nflat io n press ure la ­
bel, you sho uld dete rm ine the proper tire in fla­
tion press ure for those tires) .
As a n ad ded safety featu re, you r vehicle has been
equipped wi th a t ire p ress ure mon itor ing system
(TPMS) t hat ill umi nates a low tire p ressure tell ­
ta le w hen one or mo re of your tires is s ignificant ­
l y under -inflated. According ly, w hen the low ti re
pressure telltale illum inates, you sho uld stop and
c h eck your t ires as soon as possible, and inflate
them to the proper pressure. Dr iv ing on a sign ifi­
cant ly under -inflated t ire ca uses the t ire to over ­
heat and ca n lead to tire fa ilu re . U nder-inflation
also red uces fue l eff ic iency a nd tire tread life,
and may affect t he ve hicl e's handling a nd s top-
ping ability.
II>-

a co ,...,
N
" N ,...,
0 0 \,;J ' Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsib ility to ma intain correct tire pressure,
even if under-inf lation has not reached the level
to trigger illum ination of the TPMS low tire pres­
sure telltale .
Your veh icle has also been equ ipped w ith a TPMS
malfunct ion indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined w ith the low tire
pressure telltale. Whe n the system detects a
malfunct ion, the telltale will flash for approxi­
mately one minu te and then remain cont inuous ly
i llum inated. This sequence wi ll continue upon
subseq uen t veh icle start -ups as long as the ma l­
function exists.
When the malfunct ion i ndicator is ill uminated,
the system m ay not be ab le to detec t or sig nal
l ow tire press ure as intended. TPMS ma lfunctions
may occur for a var iety of reasons, incl uding the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly. Always check the TPMS malfunction telltale after rep lacing one or
more t ires or whee ls on your vehicle to ensu re
that t he replacement or alternate ti res and
wheels allow the TPMS to cont inue to func tion
p roperly.
If the tire pressure monitoring system
indicator appears
A ppl ies to: ve hicles with Tire Pressure Moni toring System in­
di cato r
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction .
Fig. 1 89 Instrument cl uste r: in dicator l ight w it h m essage
Wheels
Using the ABS sensors, the tire pressure monito r­
ing system compares the tire tread circumfer­
ence and vibration characterist ics of the ind ividu ­
al tires. If the pressure changes in one or more
t ires, th is is indicated in the instrument cluster
display with an indicator l ight
IE and a message .
If only o ne tire is affected, the location of tha t
t ir e will be indicated .
The tire pressures must be stored in the Infotain­ ment system again each time the pressures
change (switching between partial and full load
pressure) or afte r changing or replac ing a tire on
yo ur vehicle
Q page 220. The tire p ressure mon i­
tor ing system on ly mon itors the t ire pressure you
have stored. Refer to the t ire press ure label fo r
the recommended ti re pressure for yo ur vehicle
Q page 211, fig. 188 .
Tire tread c ircu mfe rence and vibr ation cha racter ­
istics can change and ca use a tire press ure warn­
ing if:
- the t ire pressure in one or more tires is too low
- the t ire has str uctural damage
- the t ire was replaced or the t ire pressure was
changed and it was not stored
Q page 220
- the spare tire* is i nstalled
Indicator light s
IE-toss of pressure in at least one tire Q & .
Check the tires and replace or repair if necessary .
Check/correct the pressures of all four tires and
store the pressu re again in the Infotainment sys­
tem
Q page 220.
m ( T ire Pressure Monitoring System) Ti re
pressure: System malfunction!.
If rn:m appears
after switching the ignition on or while driving
and the
IE indicator light in the instrument clus­
te r blinks for approx imately one minute and then
stays on, the re is system malf unct ion . Try to
store the co rrect t ire pressu res
Q page 220. If
t h e indicat or light does turn off or turns on agai n
af ter a sho rt pe riod o f time, d rive to an au thor­
ized Audi dea ler or authorized Audi Service Facili ­
ty immediate ly to have the ma lfunction correct-
ed.
~
219

Wheels
A WARNING
-If the t ire pressure indicator appears in the
display, reduce your speed immediate ly and
avoid any hard s teer ing or braking maneu­
vers . Stop as soon as possib le and check the
t ir es and thei r pressu re .
- The driver is responsib le for main taining the
correct tire pressure. You mus t check t he
t ir e pressure regu larly.
- Under certain conditions (such as a sporty
dr iv ing style, winter cond itions o r unpaved
ro ads), the tire p ressure mon itoring system
in dicator may be delaye d.
(D Tips
- The t ire pressu re monitoring sys tem can al­
so stop work ing when there is an ESC mal­
fun ct ion.
- Using snow chains may result in a system
malfu nction.
- The t ire pressu re monitoring sys tem in your
A udi was calibrated with "A udi Orig inal
T ires "~ page 208. Using these ti res is re c­
ommended.
Storing tire pressures
Applies to: vehicles with Tir e Pressure Monitor ing System in­
dicator
I f the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys­ tem .
.,. Make sur e before sto ring that t he tire pressures
of a ll fo ur t ires meet the specified val ues and
are ada pted to the load
c:;> page 211 .
.,. Switch the ign ition on .
.,. Se lect : the ICARI fu nction bu tton> ( Car )* Sys­
tems
con trol button > Service & control > Tire
pre ssure monitor > Store tire pre ssure > Yes,
store now .
(D Tips
Do not store the tire pre ssu res i f snow chains
are installed.
220

Care and cl eaning
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­ ing the underbody or the inside of the wheel
housings .
- After washing the vehicle, the braking effect
may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
c reases the risk of an acc ident. The brakes
must be d ried first w ith a few careful b rake
applica tions.
@ Note
- If you wash the veh icle in an automatic car
wash, you m ust fold the exte rior m irrors i n
to reduce the risk of damage to the mirrors.
Power folding exte rior m irro rs* must o nly
be fo lded in and out using the powe r folding
funct ion .
- To reduce t he risk of paint damage , do no t
wash the vehi cle i n direct sunlig ht. - T
o red uce the risk of damage to the s urface,
do not use insect removing sponges, kitchen
sponges o r similar items .
- Matte finish painted vehicle components:
- To reduce the r isk of damage to the sur-
face, do not use pol ish ing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
f inish paint. The paint could be damaged
when the stickers or magnets a re re­
moved.
@ For the sake of the environment
Only wash the veh icle in facilities spec ially de­
s igned for that pu rpose. This will reduce the
r isk of dirty wate r contam inated with o il from
en te ring the sewe r system.
Cleaning and care information
W hen clea ning and ca ring for ind ividua l vehicle
components, refer to the fo llow ing tables. The
information contained there is simply recom­
mendations. For questions or for components t
h at are not listed, cons ult an autho rized Audi
dealer or author ized A udi Servi ce Fac ility. Also
fo llow the information found
in ¢,&. .
Exterior cl eanin g
Component Situation Solution
Wind shield wiper
Deposits soft cloth with glass cleaner,
¢ page 45
blades
Headli ght s/
Deposits Soft sponge with a mild soap so lution3
)
Tail light s
S en sors /
Deposits Sensors: soft cloth with solvent-free cleaning solution
cam era l ens es Camera lenses: soft cloth w ith alcohol -free cleaning solu-
tion
Snow/ice Hand brush/solvent-free de -icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
E
xhaust tail pip es Road salt Water, clean ing solution su itab le for stainless stee l, if nee-
essary
D ecor ativ e part s/ Deposits Mild soap solution a), a cleaning solution suitable for stain-
trim less steel, if necessary
222

Care and cl eaning
Component Situation Solution
Tex tile s
Deposits adhering to Vacuum cleaner
art ifici al l eat her, the surface
A lca ntara Water -based deposits Absorbent cloth and mild soap solut
iona>
such as coffee, tea,
blood, etc.
O il-based deposits Apply a m ild soap solution
a), blot away the dissolved oil or
such as oil , make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain remover, blot with absorbent material, treat
as ink, na il polish, la- afterward with mild soap solution, if necessary a)
tex paint, shoe pol-
ish, etc.
Natural leathe r Fresh stains Cotton cloth
with a mild soap so lutiona >
Water-based deposits Fresh stairns : absorbent cloth
such as coffee, tea, Dried sta ins : stain remover suitable for leather
blood, etc.
Oil -based deposits Fresh stairns : absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc. Dried stains : grease dissolving spray
Special deposits such Spot remover suitab le for leather
as ink, nai l polish, la -
tex paint, shoe pol-
ish, etc.
Care Regula rly apply cond it ion ing cream that p rotects from
lig ht and penetrates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plastic parts
al Mild soap solution: maximum two tablespoons of neutral soap in 1 quart (1 liter) of water
_& WARNING
The windsh ie ld may not be treated wi th wa­
ter-repelling windshield coating agents. Un ­
favorable conditions such as wetness, dark ­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
-Headlight s/tail light s
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form .
-Wheel s
224
- - Never use any paint polish or other abra­
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately.
- Cam era lens es
- Neve r use wa rm or hot water to remove
snow or ice from the came ra lens . This
could cause the lens to crack .
- Neve r use ab rasive cleaning m aterials or
a lcohol to clean the camera lens . This
could cause scratches and cracks .
-Door wind ow s
- Remove snow and ice on windows and ex-
terior mirrors with a plast ic scraper. To

Emergency assistance
Emergency assistance
General information
.,. Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
.,. Set the parking brake .
.,. Switch the emergency flashers on .
.,. Set up the warning triangle r=;,page 226 .
.,. Have the passengers exit the vehicle . They
should move to a safe place, for example be­
hind a guard rail.
A WARNING
Follow the steps given above. This is for your
protection and the for the safety of other driv­
ers.
Equipment
Warning triangle
A pplies to: ve hicles w ith warning triangle
Fig. 190 Luggage compa rtment lid : wa rnin g triangle
The warning triangle placed in the vehicle at the
factory is located in the luggage compartment.
.,. To remove the warning triangle, press the re-
tainer in the direction of the arrow
r:;, fig . 190
and fold the holder down.
The luggage compartment lid is only designed to
hold the warning triangle offered by the Audi
Genuine Accessories program.
226
Vehicle tool kit
Fig. 191 Luggage compartment: vehicle tool kit
The vehicle tools and vehicle jack* are stored in
the luggage compartment under the floor cover.
.,. Lift the cargo floor by the plastic handle.
.,. Hook the handle into the luggage compartment
weather strip.
.,. Turn the handle counter-clockwise and remove
the cover or the spare tire* .
.,. Unhook the cargo floor before clos ing the lug­
gage compartment lid.
A WARNING
I mproper use of the veh icle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if yo u
use the hex head, potentially causing an ac­
cident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­
stances should it be used to lift heavy
vehicles or other loads; you risk injuring
yourself.
- Never start the engine when the vehicle is
raised, which could cause an accident .
- Support the vehicle securely with appropri­ ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a po­
tential risk for injury .
- Never use the jack supplied with your Audi
on another vehicle, particularly on a heavier
one. The jack is only suitable for use on the
vehicle it came with.

a co .... N
" N .... 0 0 \.J ' (D Tips
The vehicle jack* in your vehicle is mainte­
na nee-free.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel .
'"After you experience a tire failure, pull the car
well away from moving traff ic and try to reach
le ve l ground before you stop ¢,&. .
'"All passe ngers should le ave the car and move
to a safe location (for instance, be hind the
guardra il) ¢ ,&. .
.. Engage the parkin g brake to p revent your vehi ­
cle from rolling
unintentionally ¢,&. .
'"Move selecto r lev er to p osition P ¢ ,&. .
'"If you are towing a trailer, unh itch the trailer
from your veh icle.
'" Take the jac k and the sp are tir e* out of the lug­
gage compartment
i::> page 226 .
A WARNING
You or your passengers cou ld be inju red w hile
chang ing a wheel if you do not follow these
safety precautions :
- If you have a flat t ire, move a safe distance
off t he road. Tur n off the engine, t urn the
emergency flashers on and use other warn ­
ing devices to alert other motorists .
- Make s ure tha t pa ssengers w ait in a sa fe
place away from the vehicle and we ll away
from the road and traffic.
- T o help prevent the vehicle from moving
sudden ly and possibly slipping o ff th e jack,
always fully set the parking brake and b lock
the front and back of the wheel diagonally opposite the wheel be ing changed. When
one front whee l is lifted off the ground,
placing the Automatic Transm ission in P
(Park) w ill
not prevent the veh icle from
moving.
Em ergenc y ass is tanc e
-Before you change a whee l, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack.
- Always store the vehicle too l kit, the jack
and the replaced tire in the luggage com­
partment
¢ page 130.
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
tro ls for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the
jack ¢ page 229 .
Changing a wheel
When you change a wheel , follow the sequence
described below step-by-step and in exactly that
order .
l. Activate the vehicle jack mode* ¢ page 229.
2. Remove the deco rati ve wheel co ver* or the
wheel bolt c aps *. For more details see also
¢ page 228, Decorative wheel covers or
¢ page 228, Wheels with wheel bolt caps .
3. Loosen the wheel bolt s ¢page 229.
4. Locate t he p roper mount ing point for the
jack and align the jack be low that poin t
¢page 229 .
S. R ais e the car with the jack ¢ page 229 .
6. Remove the wheel with the fl at tir e and then
install
the spare ¢ page 231.
7. Tig hte n all wheel bolts lightly .
8 .
Lower the vehicle with the jack .
9 . Use the wheel bolt wrench and
firml y tighten
all wheel
bo lts ¢ page 229.
10. Replace t he decorat ive wh eel cover * or the
wheel bolt cap s*.
11. Deactivate the vehicle jack mode* in t he
MMI :
ICAR I function button > (Car )* sys tem s
contro l button > Ser vicing & che cks > Air
s usp.: jack mod e> Off.
The vehicle jack mode * switches off automatica l-
ly at speeds abov e 6 mph (10 km/h).
.,.
227