2018 AUDI A4 ECO mode

Warm and cold
Warm and cold
Climate control system
Description
The climate control system warms, cools and re­ moves humidity from the air in the vehicle interi­
or. It is the most effective when the windows and
sunroof * are closed. If there is a bui ld-up of heat
inside the vehicle, ventilation can he lp to speed
up the cooling process.
I n all heating mode f unctions except for
defrost,
the blower only switches to a higher speed once
the engine coolant has reached a sufficient tem­
perature .
Pollutant filt er
The po llutant filter removes poll utants such as
dust and pollen from the a ir .
Ke y recognit ion
The climate control settings are automatically
stored and assigned to the remote contro l key
that is in use .
76
® For the sake of the environment
-If you would like to reduce fuel consump­
t ion, sw itch the air conditioning
off. This
will also reduce emissions.
- In veh icles with a diesel engine, you can
switch the auxiliary heater
off in the Info­
tainment system.
(D Tips
- To prevent interference with the heating
and cooling output and to prevent the win­
dows from fogging over, the air intake in
front of the windshie ld must be free of ice,
snow or leaves.
- Condensation from the cooling system can
dr ip and form a pudd le of water under the
vehicle . This is norma l and does not mean
there is a leak.
- The energy management system may tem­ porarily switch
off certain functions, such as
the seat heating* o r rear window defogger.
T hese systems are ava ilable again as soon
as the ene rgy supply has been restored.

Warm and cold
3 zone deluxe automatic climate control
Operation
.... M
~ a,
Fig. 90 3-zone de lu xe a uto mat ic cl imate contro l; cockpit controls
Fig. 9 1 3-zone de luxe automatic cl imate control system: rear controls
Press the knobs, buttons or rocker switches to
turn the functions on or off . When the funct ion is
sw itched on, the LED in the respect ive button or
knob t urns
on ¢ fig. 90. The rocker switc hes are
se nsitive to to uch. The drive r and front passenger
sett ings can be ad justed sepa rately.
You can adjust the settings for the rea r of the ve­
hi cle using the controls in the rear
~ fig. 91 .
On right-hand dr ive vehicles*, the functions of
the rocker sw itched ® and ® are switched .
OFF
clima te control sy stem
You can switc h the cl imate control system on and
off using the OFF button.
It also sw itches on when you press another button or a knob. A
irflow
from outside is b locked when the clima te control
system is sw itched off.
A/C Cooling mode
You can switch the coo ling mode on or off using
the rocker switch ®· The air is not coo led and hu­
mid ity is not removed when cooling mode is
switched off. This can cause fog on the w indows .
Cooling mode switches off automatically when
t h e outs ide tempe ra ture is below zero .
A/Ceco cooling mode*
You can switch the eco cooling mode on or off us-
ing the rocker switch ®· The climate control
..,.
77

Warm and cold
system operates most efficiently in eco cooling
mode.
A/C MAX cooling mode*
You can switch the maximum cool ing mode on or
off using the rocker switch@. Th e air is not
coo led and humidity is not removed when cooling
mode is switched off. This can cause fog on the
windows. Cooling mode switches off automati­
cally when the outside temperature is below
zero. When the cooling mode is switched on, the
vehicle interior is cooled as quickly as possible
and dehumidified .
c:E) Recirculation mode
In recirculation mode, the air inside the vehicle is
circu lated and filtered. This prevents the unfil­
tered air outside the vehicle from entering the
vehicle interior. Switching recirculation mode on
when dr iv ing through a tunnel or when s itting in
traffic is recommended
Q &, .
Using the button, recirculation mode is~ using
the button. You can also switch the recirculation
mode off by pressing the knob (D or the ~ but­
ton.
AUTO
Automatic mode
Automatic mode maintains a constant tempera­
ture inside the vehicle. Air temperature, airflow
and air distribution are controlled automatically .
You can switch automatic mode on or off by
pressing the
knob@.
Temperature
You can adjust the temperature between 60°F
( + 16°()
and 84°F ( +28°() by turn ing the knob
(D . Outs ide of this range, LO or HI will appear in
the climate control system display . In both set­
tings, the climate control runs constantly at the
maximum cooling or heating level. The tempera­
ture is not regulated.
The temperature can be adjusted in the rear us­
ing the rear contro ls
Q fig. 91.
86'~ Blower
You can adjust the vo lume of air generated by the
blower to your preference using the rocker switch
@ . The blower should always run at a low setting
78
to prevent the windows from fogging and to en ­
sure a continuous exchange of air inside the vehi­
cle. To have the blower regulated automatically,
press one of the knobs
(D .
Air distribution
You can use the rocker sw itches @to adjust the
vents where the air will flow out of. Press the
rocker switches @repeatedly unti l the desired
air distribution setting is displayed in the climate
control system controls. To have the air distribu­
tion regulated automatically, press one of the
knobs
(D .
""lll"' OPEN/CLOSE the wide vent
You can open and close the wide vent in the cock­
pit using the rocker switch ®·
JI~ Seat heating and ventilation*
If you press the button J ,J, the seat heating/
ventilat ion is switched on at the highest leve l (3) .
The LEDs indicate the temperature level. To re­
duce the temperature, press the button again. To
switch the seat heating/ventilation off, press the
button repeatedly until the LED turns
off.
3% Defrosting
The windshield and side windows are defrosted
or cleared of condensation as quick ly as possible .
The maximum amount of air flows mainly from
the vents below the windsh ield. Recirculation
mode switches off. The temperature should be
set at
+72°F (+22°() or higher . The temperature
i s controlled automat ically .
Defrost is switched on and off
3% using the but­
ton. You can switch the function off by pressing a knob
(D .
Applies to vehicles with windshield defogger: the
windshield defogger switches on automatically
when outside temperatures are low. If you would like to sw itch the windshield defroster on man­
ually, press the
3%. The LED in the button blinks.
ClWREAR Rear window defogger
Press the button [email protected] switch the rear window de­
fogger on. It on ly operates when the engine is
running. It switches off automatically after
10 to .,,.

a co .... N ,....
N .... 0 0
3 co
20 minutes, depending on the outside
temperature.
To keep the rear window defogger on contin uous­
l y, press and hold the
QWREAR button longer
than
3 seconds. This is stored unti l the ignition is
switched off .
SYNC Synchronization
Use the rocker switc h® to sele ct the funct ion.
When synch ronization is switched on, the set­
tings for the driver's side are applied to the front
passenger's side and the rear (except for seat
heating/venti lation*) . When the settings on the
front passenger's side or in the rear are changed,
the synchron iz at ion is automatically sw itched off
and
3 -z one appears in the display .
SET REAR function
Use t he rocker switch ® to select the function .
When the function is switched on, you can adjust
all settings for the rear us ing the climate control
system controls in the cockpit. The rear climate
control system controls cannot be operated at
the same time . This function switches off auto­
mat ically after a certain period of time or after
leaving the menu.
Vent s
You can open or close the center and rear vents in
the cockpit and the vents in the rear center con­
sole us ing the r idged thumbwheels . The levers
adjust the d irection of the airflow from the vents.
The wide vent is opened and closed using the
r ocker switch
® ·
Residu al heat
You can activate the residual heat funct ion when
the ignition is switched off by pressing the knob
(D . The res idual heat from the coolant is used to
h eat the vehicle inte rior. The residual heat func­
tion swi tches off automatically afte r abou t 15
minu tes .
A WARNING
- You should not use the recirculation mode for an exten ded period of time, because no
fresh a ir is drawn in and the w indows can
Warm and c old
fog when cooling mode is switched off. This
increases the r isk of an accident.
- Individuals with reduced sensitivity to pain
or temperature could develop burns when
using the seat heat ing* function. To reduce
the risk of injury, these individua ls should
not use seat heating*.
(D Note
To avoid damaging the seat heat ing* ele­
ments, do not knee l on the seats or place
heavy pressure on one area of the seat.
Setup
The climate control system basic settings ore ac­
cessed in the Infotainment system .
.,. Select in the Infotainment system : I MENU! but­
ton
> Vehicle > l eft control button > Ai r co ndi ­
tioning
Auto recircu lation
When switched on, a utomat ic rec irculat ion con­
trols the recircu lation mode automatically . You
must press the
®MAX button if fog forms on
the windows.
Automatic auxiliary heater*
T he aux iliary hea ter he lps to wa rm the vehicle in ­
terior more q uickly.
Steering wheel heating
Applies to: vehicles with steering wheel heating
The steering wheel rim con be heated.
.,. Press the bu tton on the m ultif unct ion steeri ng
wheel to switch the steering whee l heating on
and
off~ r=:> poge 15, fig . 11 . The message
Steering wheel heating : on /Steering wheel
heating: off
appears in the instrument cluster
disp lay.
The temperature is maintained at a constant lev­ el when steering wheel heating is switched on .
T he s teer ing whee l heating se tt ings a re stored
automat ica lly and assigned to the remo te control
key that is in use.
79

Driving
Driving
General information
Breaking in
A new vehicle must be broken in for the first 1,000 mi les (1,500 km). Do not drive at speeds
that will exceed 2/3 of the maximum perm itted
engine speed (RPM) for the first 600 miles
(1,000 km), and avoid full acceleration during
this period . You may gradually start increasing
the RPM and the speed between 600 miles (1,000 km) and 1,000 miles (1,500 km) .
During the first hours of use, the engine has a
h igher internal friction than later on when all
moving parts have settled into place with each
other.
How the vehicle is driven during the first 1,000
miles (1,500 km) also affects the engine quality.
Drive at moderate engine speeds after the initial
break-in period, particularly when running a cold
engine. This will reduce engine wear and improve
the mileage .
Do not drive at too low of an engine speed (RPM) .
Shift down if the engine stops running "smooth­ ly". Extremely high engine speeds are automati­
cally reduced .
Reducing the risk of vehicle damage
(D Note
When driving on poor roads, by curbs and on
steep ramps, make su re that low-hang ing
components such as the spoi ler and exhaust
system do not come into contact with these
or they could be damaged. This especially ap­
plies to vehicles with low ground clearance
and vehicles that are heavily loaded.
Driving through water on roads
Note the following to reduce the risk of vehicle
damage when driv ing through water, for example
on flooded roads:
-The water must not be any higher than the bot­
tom of the vehicle body .
80
-Do not drive faster than walking speed .
A WARNING
After driving through water or mud, the effec­
tiveness of the brakes may be reduced due to
moisture on the brake rotors and brake pads.
A few careful brake applications should dry
off the brakes and restore the full braking ef­
fect .
{CT) Note
-Vehicle components such as the engine,
transmission, suspension or electrical sys-
tem can be severely damaged by driving
through water .
-Always switch the Start/Stop system* off
when driving through water <=:>page
85.
@ Tips
-Determine the depth before driving through
water.
-Do not stop the vehicle, drive in reverse or
switch the engine off when driving through
water .
'
-Keep in mind that oncoming vehicles may
create waves that raise the water level and
make it too deep for your vehicle to drive
through safe ly .
-Avoid driving through salt water, because
this can cause corrosion .
Economical and environmentally -friendly
dr iving
The amount of fuel consumption, the environ­
mental impact and the wear to the engine,
brakes and tires depends mostly on your driving
style. With an anticipatory and economic driving
style, fuel consumption can be reduced by ap­ proximately 10-15%. The following tips will help
you conserve the environment and your money at the same time .
Anticipatory driving
A vehicle uses the most fuel when accelerating.
When you drive with anticipation, you do not need to brake as often and so you accelerate less.
When possible, let your vehicle coast with a gear
..,.

you stop it. You also cannot lock the vehicle from
the outside .
Applies to: vehicles with au tomatic transm issions
Shift to P , otherwise vehicle can roll away.
Doors do not lock if gearshift is not in P
This message appears for safety reasons if the
selector lever is in the N position when you
sw itch the ignition off. Move the selector leve r to
the P position. Otherwise the vehicle is not pro­
tected from ro lling and it cannot be locked .
DJ Remote control key: hold back of key
against the designated area . See owner 's man­
ual
If the indicator light turns on and th is message
appears, there is a malfunction
q page 85 .
Applies to: vehicles with automatic transmissions
Shift to P before leaving car, otherwise vehicle
can roll away
This message appears if the driver's door is
opened while the ignition is switched on and the
transmission has not been shifted to the P posi­
tion . Sh ift the transmiss ion into the P position
and turn off the ignition if you are leaving the ve­
hicle . Otherwise the vehicle could roll. Also see
c::> page87 .
Starting the engine when there is a
malfunction
It may not be possible to start the engine under
certain circumstances, for example if the battery
in the vehicle key is drained, if interference is af­
fected the key or if there is a system malfunc ­
tion .
Fig. 94 Cente r console/ remote contro l key: starting t he
eng ine if there is a malfunc tion
Driving
Requirement: the message Remote control key:
hold back of key against the designated area .
See owner's manual
must display and the DJ i n­
dicator light must turn on.
.,. Place the remote control key on the location
shown in the illustration
y >l) c::> fig . 94.
Applies to: vehicles with manual transmission
.,. Press the clutch pedal.
Applies to: vehicles with automatic transmissions
• Press the brake pedal.
.. Press the !START ENGINE STOP ! button. The
engine will start.
.,. Drive to an authorized Audi dea ler or author­
ized Aud i Service Facility immediately to have
the malfunction corrected.
@ Tips
You can view the message again by pressing
the
I S TART ENGINE STOP I button.
Start/Stop system
Description
Applies to: vehicles with Start/Stop system
The Start/Stop system can help increase fue l
economy and reduce CO2 emissions.
In Sta rt/Stop mode, the engine shuts off auto­
matically when the vehicle is stopped, such as at
a traffic light. The ignition remains switched on
during this stop phase . The engine wi ll restart
automatica lly when needed .
Th e Start/Stop system is a utomaticall y activated
as soon as the ignition is switched on.
Basic requirements for Start/Stop mode
-The driver's door must be closed .
-The driver's seat belt much be fastened.
- The hood must be closed.
- The vehicle must have driven faster than
2 mph
(3 km/h) since the last time it stopped .
- A trailer must not be hitched to the vehicle.
If you leave the vehicle during a stop phase, the
engine can be restarted within approximately 30
seconds if the following requi rements are met:
IJ>
85

a co .... N ,....
N .... 0 0
3 co
@j indicator light appears in the instrument clus­
ter disp lay, the engine will not be stopped, for
examp le in the following situations:
- T he eng ine has not reached the minimum re­
quired temperature for Start/Stop mode.
- T he interior temperature selected by the cli-
mate contro l system has not been reached .
- T he outs ide temperature is ext remely h igh/low.
- The windshield is being defrosted.
- The vehicle battery charge level is too low.
- The steering whee l is turned at a sharp angle or
is mov ing .
- After engaging the reverse gear.
- On sharp inclines.
- At high a ltitudes.
Engine automatically restarts
The standard Start/Stop mode will be cance led
during a stop phase in the follow ing s ituations .
The engine restarts without any action by the
d river.
- The vehicle rolls, for examp le while on a slope.
- The interior temperature differs from the tem-
perature se lected in the A/C system .
- The windshield is being defrosted .
- The brake pedal is pressed several times in a
row.
- The vehicle battery charge level is too low.
- Power consumption is high.
The engine can t urn off again when the condi­
tions for Start/Stop mode are met.
Ignition is switched off automatically
To prevent the veh icle battery from drain ing, the
ignition will switch off automat ica lly under the
following conditions :
- The Start/Stop system has stopped the engine .
- The veh icle is stationary.
- You left the vehicle and the engine was not re -
started within approximately 30 seconds .
I f this happens, you wi ll see the message
Igni­
tion turns off automatically
in the instrument
cluster and the activated low beams are replaced by the parking light. The parking lights will
sw itch off after approximately 30 minutes or
when you lock the vehicle .
Driving
The ignition also switches off when you lock the
vehicle from the outside during a stop phase.
If the Start/Stop system has not turned off the
engine or if you have switched the Start/Stop sys­
tem off manually, the ignition will not be auto ­
matically switched off and the engine will contin­
ue to run
¢ .&..
A WARNING
To reduce the risk of poisoning, never allow
the eng ine to run in confined spaces .
(D Tips
Applies to : vehicles with auto matic transmissions
-
- If you leave the vehicle with the D/S or R se­
lector lever position engaged, the parking
brake is automatically set.
- If you select the D or N selector lever posi­
tion after shifting into reverse, the vehicle
must be driven faster than 6 mph ( 10 km/h)
in o rder fo r the engine to switch off again .
' Manually switching the Start/Stop system
, off/on
Applies to: vehicles wi th Start/Stop syste m
If you do not wish to use the system, you can
switch it off manually.
Fig. 96 Cente r console : Start/Stop system button
.,. To switch the Start/Stop system off/on man­
ually, press the
l v'> ~I button. The LED in the but­
ton turns on when the system is switched off .
(D Tips
If you switch the system off during a stop
phase, the engine will start aga in automati­
cally .
87

Driving
"'T o activate hill hold assist, press and hold the
brake peda l for several seconds. The vehicle
must be in an uph ill direction of travel.
Afte r releasing the bra ke pedal, the brak ing pow­
er is ma intained for a brie f
moment¢ A to pre­
vent the vehicle from rolling back when starting .
During this time, you can eas ily beg in to move
your veh icle.
A WARNING
- If you do not begin dr iving immediately or
the engine stalls after releas ing t he brake
peda l, yo ur vehicle may begi n to roll back­
ward . Press t he b rake pedal o r set the park ­
i ng bra ke immed iate ly.
- The intelligent techno logy of hill hold assist
c annot overcome the lim itations imposed by
n atu ral physical laws. The incre ased comfo rt
offered by h ill hold assist sho uld not cause
yo u to take safety risks .
- Hill ho ld assis t can not hold the veh icle in
place on all h ills ( for example, i f the gro und
is slippery or icy) .
- T o reduce the risk of an ac cident, always
make sure the vehicle is si tuated safely
whi le stat ionary.
Driving offroad
General information
A ppl ies to: a ll r oad
The electro nic stabilization co ntrol (ESC) func­
tions were e nhanced for dr iv ing offroad. Offroad
mode c an be ac tivated whe n driving in situat ions
where slipp age or a different ia l loc k func tion is
necessary ¢ page 147. The h ill descent ass ist is
a lso available, which automatica lly brakes the
ve­
h icle and mainta ins a constant speed as a result
¢ page 148. In add ition, your Audi prov ides con­
tinuous all wheel drive.
However , you r Audi is not an offroad vehicle.
Only drive in terrain that is su itable for the vehi ·
cle and your driving abilit y. Never take an y un·
neces sary risks!
90
Afte r driving offroad
- After driving off road , remove b ranches and
other debris from the rad iator grille, under ­
body, and wheels . Look especially fo r foreign
objects (such as stones) that may be st uck in
the t ire tread.
- Clean the vehicle body and underbody and
in­
spect the vehicle for possible damage.
- Clean the windows, headlights, tail lights and
the license p late if they are dirty.
- Per form a brake test (especia lly after d riving
throug h water) .
A WARNING
-Be especially aware and attentive when d riv ­
ing under diff icu lt cond itions. Vehicle dam­
age and in juries may occur when driving at
excess ively high speeds or with incorrect
driving maneuvers.
- Always ad just yo ur speed and driving sty le
to the roads, terrain, traffic and weat her
conditions . Drive especially slowly if there is
low visibility when off road.
- Please note that t he wheels can sp in mo re
and the vehicle can swerve when in offroad
mode, espe cially when the road is slippery
or h as loose s urfa ce mate rial.
- D riving stability is reduce d when in offroad
mode.
@ For the sake of the environment
Avo id harm ing the env ironmen t and show
conside ration fo r nat ure.
(D Tips
Only drive where it is permitted and always
stay on the prov ided roads and paths .
Driver messages
Applies to : allroad
There is only one right way to drive in difficul t
conditions: slowly and with caution!
Observe the following when driving on unpaved
r oads :
1111>