2017 VOLVO XC90 TWIN ENGINE HYBRID light

||
INSTRUMENTS AND CONTROLS
114
been running, the power windows can be oper-ated for several minutes after the ignition hasbeen switched off, or until a door has beenopened.

NOTE
•Movement of the windows will stop if theyare obstructed in any way. If this happenstwice in succession, the automatic func-tion will not work for several minutes andthe window can be closed by holding thebutton up.
•To reduce buffeting wind noise if the rearwindows are opened, also open the frontwindows slightly.

Manual up/down
–Move one of the controls up/down slightly.
>The power windows move up/down aslong as the control is held in position.

Auto up/down
–Move one of the controls up/down as far aspossible and release it.
>The window will open or close completely.
Resetting
If the battery has been disconnected, the autoopen function must be reset so that it will workproperly
1. Gently raise the front section of the button toclose the window and hold it for one second.
2. Release the button briefly.
3. Raise the front section of the button againfor one second.

Related information
•Child safety locks (p. 257)
Rearview mirror
The interior rearview mirror has an auto-dimfunction that helps reduce glare from followingvehicle's headlights.
Auto-dim function
The auto-dim function is controlled by two sen-sors: one pointing forward (located on the for-ward-facing side of the mirror, which monitors theamount of ambient light) and one pointing rear-ward (located on the side of the mirror facing thedriver at the upper edge, which senses thestrength of following vehicles' headlights), andwork together to help eliminate glare.

NOTE
Obstructing the forward sensor with e.g.,parking stickers, transponders, etc., or the rearsensor by loading the cargo area or the rearseat in such a way that light is prevented fromreaching the sensor will reduce the auto-dimfunction in the interior rearview mirror andoptional auto-dim function in the door mirrors.
The auto-dim function is always active while thevehicle is being driven except when the reversegear has been selected. The level of sensitivityfor this function can be set to three levels, whichaffect the rearview mirror and door mirrors.

INSTRUMENTS AND CONTROLS
}}
115

NOTE
When the level of sensitivity is changed, thischange will not be noticeable immediately butwill take effect after a short period of time.
The level of sensitivity is set from the center dis-play:
1.Tap Settings in Top view.
2.Tap My CarMirrors.
3.Under Auto Dim Mirrors, select Normal,Dark or Light.

Related information
•Adjusting the power door mirrors (p. 108)
Using sun shades
Both rear doors have integrated sun shades.
Rear doors
Hook and locking mechanism
1.Pull up the sun shade and hook it to theupper section of the door frame.
2. Lock the sun shade by moving the lockingmechanism upward.
The window can be opened/closed when the sunshade is being used.

Related information
•Power windows (p. 113)
Settings view
The center display's Settings view is used tomake many of the vehicle's function settings andto display vehicle-related information.
Opening Settings view
Top view with the Settings button
1. Pull down the tab on the upper edge of thecenter display to open Top view.
2.Tap Settings.
3.Tap one of the categories displayed and nav-igate to sub-categories and settings by tap-ping again.
4.Tap Back to go back in Settings view.
Tap Close to close Settings view.

||
INSTRUMENTS AND CONTROLS
* Option/accessory, for more information, see Introduction.116

Changing a setting
A sub-category in Settings view with various possiblesettings
1. Tap the category/sub-category to navigate tothe desired setting.
2.Change the setting(s).
> The changes are saved immediately.

Types of settings
Type ofsettingDescription
TriggerfunctionStarts an app or a separate viewfor more advanced settings. Tapthe text to e.g., connect aBluetooth device.
RadiobuttonSelect one of the possible set-tings by tapping the desired radiobutton to e.g., change the systemlanguage.
Type ofsettingDescription
Multi-selectionbutton
Select a level for a particular set-ting by pressing the desired partof the button e.g., to set thedesired level for City Safety.
CheckboxTap to activate/deactivate a func-tion e.g., to select automatic startfor steering wheel heating.
SliderSelect a level for a function bypressing and dragging the slidercontrol e.g., to set a volume level.
Informa-tion dis-play
This is not an actual setting butdisplays information such as thevehicle's VIN number.
Related information
•Center display overview (p. 33)
•Navigating in the center display's views(p. 43)
•Using the center display (p. 50)
•Changing system settings in Settings view(p. 118)
•Categories in Settings view (p. 116)
Categories in Settings view
Settings view consists of a number of main cate-gories and sub-categories that contain settingsand information for many of the vehicle's fea-tures and functions.
The main categories in Settings view are: MyCar, Sound, Navigation, Media,Communication, Climate and System.
Each main category, in turn, contains several sub-categories with possible settings. The tableshows the first level of sub-categories. The possi-ble settings for a function or area are describedin greater detail in their respective articles in theowner's manual. For system settings not descri-bed in the respective articles, see "Changing sys-tem settings in Settings view."
My Car
Sub-categoriesType of setting
DisplaysPersonal
IntelliSafeCombination
Park AssistGlobal
Drive Mode/IndividualDrive Mode*
Combination
LightsCombination
MirrorsPersonal
LockingCombination

||
INSTRUMENTS AND CONTROLS
120
3.Tap OK to confirm your choice.
For Reset Personal Settings, tap Resetfor the active profile or Reset for allprofiles for confirmation.
>The selected settings will be reset.

Related information
•Settings view (p. 115)
•Resetting user data when the vehiclechanges owners (p. 120)
•Changing system settings in Settings view(p. 118)
Resetting user data when thevehicle changes owners
When the vehicle changes owners, all user set-tings should be reset to the factory defaults.
When the vehicle changes owners, it is essentialto reset all user data and system settings to theirfactory defaults, including Volvo On Call.

Related information
•Resetting the settings view (p. 119)
•Volvo ID (p. 32)
Ambient temperature sensor
The ambient temperature sensor displays thetemperature outside the vehicle in the instrumentpanel.
Location of the ambient temperature sensor in 12"(upper) and 8" (lower) instrument panels (temperatureshown here in degrees Celsius)

NOTE
When the ambient temperature is between23° and 36 °F (–5° and +2 °C), a snowflakesymbol will be displayed next to the tempera-ture. This symbol serves as a warning for pos-sible slippery road surfaces. Please note thatthis symbol does not indicate a fault with yourvehicle.
At low speeds or when the vehicle is not mov-ing, the temperature readings may be slightlyhigher than the actual ambient temperature.

INSTRUMENTS AND CONTROLS
121

Settings
Changing measurement standard in the centerdisplay:
1. Pull down the center display's Top view andtap Settings.
2.Tap SystemUnits.
3.Select measurement standard, Metric,Imperial or US.

Related information
•Instrument panel (p. 132)
•Climate system sensors (p. 189)
Clock
The clock is displayed in the instrument paneland in the center display.
Location of the clock in the instrument panel in 12"(upper) and 8" (lower) instrument panels
Certain messages and other information in theinstrument panel may temporarily obscure theclock.
In the center display, the clock is located at theupper right of the status bar.

Settings for date and time
Select SettingsSystemDate & Time inthe center display's Top view to change the for-mat for displaying date or time.
Set the date and time by tapping the up or downarrows on the center display.
Automatic time
The function Automatic Time is also available,which adjusts the time zone automatically,depending on the vehicle's location. If AutomaticTime has not been selected, set the date andtime manually by tapping the up or down arrowson the center display.

Daylight savings time
In certain countries, an automatic change to day-light savings time can be selected by activatingAuto. If the automatic change is not available,change to daylight savings time by selecting Onor Off.

Related information
•Instrument panel (p. 132)
•Center display overview (p. 33)
•Using the center display (p. 50)

INSTRUMENTS AND CONTROLS
* Option/accessory, for more information, see Introduction.122
Head-up display (HUD)*
The head-up display provides information suchas speed, cruise control functions, navigation,traffic sign information, incoming phone calls,etc. at the base of the windshield in the driver'sfield of vision.
Incoming phone call
The HUD supplements the instrument panel andprojects information on the lower section of thewindshield. The projected information can only beseen from the driver's seat.

CAUTION
The HUD's projection unit is located in thedashboard. Avoid scratching or placingobjects on the unit's glass surface.
Example of information in the head-up display. The infor-mation shown is generic and may vary slightly from mar-ket to market or in terms of units of measure
Speed
Cruise control
Navigation
Road signs
Symbols such as the following ones may appeartemporarily in the HUD.
If the warning symbol appears, read thewarning text in the instrument panel.
If the information symbol appears, readthe warning text in the instrumentpanel.
NOTE
If the City Safety is activated, the informationin the HUD will be replaced by a City Safety-related graphic. This graphic will illuminateeven if the HUD is turned off.
A graphic for the City Safety flashes to attract the driv-er's attention

INSTRUMENTS AND CONTROLS
}}
123

NOTE
The driver's ability to see information in theHUD may be impeded by:
•the use of polarizing sunglasses
•the use of an aftermarket or non-Volvoreplacement windshield
•not sitting in the center of the driver'sseat
•objects on the HUD projector glass onthe dashboard
•certain ambient lighting conditions
•certain types of vision problems, whichmay also result in headaches or eyestrain.
•Activating/deactivating and settings forHUD are only possible when an image isprojected on the windshield. The enginemust be running.

Activating/deactivating HUD
HUD can be activated in two ways in the centerdisplay:

Via Function view
Tap the Head-up display but-ton.
Via settings
1.Tap Settings in Top view.
2.Tap My CarDisplays.
3.Select/deselect Head-Up Display.
This selection can be stored as a personal set-ting in a driver profile.

Selecting display alternatives
1.Tap Settings in Top view.
2.Tap My CarDisplaysHead-UpDisplay Options.
Tap Go to the center display's Settings viewand select Driver Display & Head-upDisplay.
3.Select : Show Navigation In Head-UpDisplay, Road Sign Information In Head-Up Display, Show Driver Support InHead-Up Display or Show Phone InHead-Up Display.
This selection can be stored as a personal set-ting in a driver profile.
Adjusting HUD brightness and height
position
1.Tap Head-up display adjustments in thecenter display's Function view.
2.Use the right-side steering wheel keypad toadjust the HUD's brightness and height posi-tion on the windshield in the driver's field ofvision.
Reduce brightness
Increase brightness
Higher position

||
INSTRUMENTS AND CONTROLS
* Option/accessory, for more information, see Introduction.124
Lower position
Confirm

Adapting brightness
The brightness of the graphics displayed in theHUD are also automatically adjusted according toambient lighting conditions. HUD brightness isalso affected by adjustments to the brightness ofthe other displays in the vehicle.

Power front seat * memory function
The position of the HUD can be stored in thepower seat's memory function.

Replacing the windshield
Vehicles with a head-up display have a specialtype of windshield meeting the requirements fordisplaying projected information.
If the windshield has to be replaced, contact atrained and qualified Volvo service technician orauthorized workshop. The correct type of replace-ment windshield must be used for a head-up dis-play.

Calibrating the horizontal position
If the windshield has been replaced, it may benecessary to calibrate the HUD's horizontal posi-tion. This means that the projected image willhave to be rotated clockwise or counterclockwise.To do so:
1. Pull down the center display's Top view andtap Settings.
2.Select My CarDisplaysHead-UpDisplay Calibration.
3.Use the buttons on the right-side steeringwheel keypad to calibrate the horizontal posi-tion.
Rotate counterclockwise
Rotate clockwise
Confirm

Cleaning
Wipe the glass covering the HUD projection unitcarefully with a clean and dry (or very slightlydamp if necessary) microfiber cloth.
Never use strong stain removers. For difficultcleaning conditions, a special cleaning agent canbe purchased at a Volvo retailer.
Related information
•Center display overview (p. 33)
•Navigating in the center display's views(p. 43)