2017 VOLVO XC90 TWIN ENGINE HYBRID light

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.310
•the lane is at the top of a hill, on anuneven road surface or over a bump.
•bad weather conditions (rain, snow, fog,slush, poor visibility, backlighting, etc).
The driver should also be aware that PilotAssist has the following limitations:
•High curbs, barriers and temporary obsta-cles (cones, barriers etc) may not bedetected or could be detected incorrectlyas side marker lines, which may create arisk of collision. The driver must ensure asafe distance to these obstacles.
•The camera or radar sensor may not beable to detect objects if there are pot-holes or if there are stationary objectspartially or completely blocking the road.
•Pilot Assist does not "see" pedestrians,animals, etc.
•Pilot Assist's steering capacity is limitedand may not always be able to help thedriver keep the vehicle in the lane.

Hands on the steering wheel
Pilot Assist only functions when the driver'shands are on the steering wheel, which is con-tinuously monitored by the system. If this is notthe case, the driver will be alerted by a text mes-sage in the instrument panel. If the driver's handsare not returned to the steering wheel, an audiblesignal will sound.
If the driver does not return his/her hands to thesteering wheel after the audible signal, Pilot
Assist will go into standby mode and must be
reactivated by pressing .
Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Changing Pilot Assist-2 speed
Different speeds can be set for Pilot Assist.
Function buttons and symbols
–Change a set speed by pressing the (1)or — (3) buttons briefly or by pressing andholding them:
•Press briefly: changes speed in+/– 5 mph (+/– 5 km/h) increments.Each press changes the vehicle's speedby +/– 5 mph (+/– 5 km/h).
•Press and hold: changes the speed+/– 1 mph (+/– 1 km/h) at a time.Release the button when the set speedindicator (4) has moved to the desiredspeed.
If speed is increased by pressing the accelerator
pedal before the button is pressed, the vehi-cle's speed when the button is pressed will

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.312
Time interval controls
Press to reduce the time interval to the vehi-cle ahead
Press to increase the time interval to thevehicle ahead
Distance indicator
In order to follow the vehicle ahead as smoothlyas possible, Pilot Assist allows the time interval tovary considerably in certain situations. At lowspeeds, when the distance to the vehicle aheadis short, Pilot Assist increases the time intervalslightly.
•If Pilot Assist does not seem to react when itis put in active mode, this may be becausethe set time interval to the vehicle aheaddoes not allow an increase in speed.
•The higher the speed, the greater the dis-tance to the vehicle ahead for a given timeinterval.

WARNING
•Only use a time interval that is suitable incurrent traffic conditions.
•A short time interval gives the driver lim-ited reaction time if an unexpected situa-tion occurs in traffic.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Deactivating/resuming Pilot Assist
Pilot Assist can be temporarily deactivated, putin standby mode and then reactivated.
Function buttons and symbols (generic illustration)

Deactivating and putting Pilot Assist in
standby mode
–Press the button (2).
>Pilot Assist will go into standby mode. The
symbol in the instrument panel willchange colors from WHITE to GRAY andthe set speed in the center of the speed-ometer will change from BEIGE to GRAY.
or
–Press the ◀ button (2).
>Pilot Assist will be turned off and shift toAdaptive Cruise Control in active mode.

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.314
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
•Distance Alert* (p. 279)
Changing target vehicles andautomatic braking with PilotAssist-2
At certain speeds, Pilot Assist can change targetvehicles and automatically apply the brakes.

Changing target vehicles
If the target vehicle turns suddenly, there may be a sta-tionary vehicle ahead
When Pilot Assist is actively following anothervehicle at speeds under 20 mph (30 km/h) andchanges targets from a moving vehicle to a sta-tionary one, the system will brake for the station-ary vehicle.
WARNING
If Pilot Assist changes targets from a movingvehicle to a stationary one at speeds above20 mph (30 km/h), the system will not reactto the stationary vehicle and will accelerate tothe previously set speed.
The driver must actively apply the brakes toslow/stop the vehicle.

Automatic standby mode when changing
targets
Pilot Assist disengages and goes into standbymode if:
•your vehicle's speed goes below approx.3 mph (5 km/h) and Pilot Assist cannotdetermine if the target object is a stationaryvehicle or some other type of object such asa speed bump, etc
•the vehicle's speed goes below approx.3 mph (5 km/h) and the vehicle aheadchanges lanes or turns so that Pilot Assistno longer has a target vehicle to follow

Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, Pilot Assist will go into standby mode andthe auto-hold brake function will activate.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.316

WARNING
Pilot Assist is not a collision avoidance sys-tem. The driver is always responsible forsteering or applying the brakes if the systemdoes not detect another vehicle.
Do not use Pilot Assist in demanding drivingconditions such as city driving or other heavytraffic situations, in slippery conditions, whenthere is a great deal of water or slush on theroad, during heavy rain or snow, in poor visibil-ity, on winding roads or on highway on- or off-ramps.
In certain situations, it may be difficult for PilotAssist to assist the driver correctly or to deac-tivate automatically. In such cases, it is advisa-ble not to use Pilot Assist. Examples of suchsituations may be:
•the lane's side market lines are missing,badly faded or cross each other.
•the division of lanes is not clear, e.g.,when a line divides or merges withanother, at exits or if there are many roadsigns/markers.
•there are edges or other lines on or nearthe lane, e.g., curbs, cracks, repairedareas, sharp shadows, etc.
•the lane is narrow or winding.
•the lane is at the top of a hill, on anuneven road surface or over a bump.
•bad weather conditions (rain, snow, fog,slush, poor visibility, backlighting, etc).
The driver should also be aware that PilotAssist has the following limitations:
•High curbs, barriers and temporary obsta-cles (cones, barriers etc) may not bedetected or could be detected incorrectlyas side marker lines, which may create arisk of collision. The driver must ensure asafe distance to these obstacles.
•The camera or radar sensor may not beable to detect objects if there are pot-holes or if there are stationary objectspartially or completely blocking the road.
•Pilot Assist does not "see" pedestrians,animals, etc.
•Pilot Assist's steering capacity is limitedand may not always be able to help thedriver keep the vehicle in the lane.
The driver can always take action to override PilotAssist.

Steep roads and/or heavy loads
Pilot Assist is primarily intended for use on rela-tively level roads. The function may not be able tomaintain the correct time interval to the vehicleahead on when driving down steep hills. Thedriver should be attentive and prepared to applythe brakes in these situations.
Do not use Pilot Assist when the vehicle is trans-porting a heavy load or if it is towing a trailer.
Additional information
•The Off Road drive mode cannot beselected if Pilot Assist is activated.
•Pilot Assist uses the vehicle's camera andradar sensor, which have certain general limi-tations. See the articles "Camera limitations"and "Radar sensor limitations" for additionalinformation.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 symbols and messages(p. 317)
•Radar sensor limitations (p. 319)
•Camera limitations (p. 323)

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.322
Radar sensor - type approval
USA & Canada:
FCC ID: L2C0054TR IC: 3432A-0054TR FCCID: L2C0055TR IC: 3432A-0055TR
This device complies with Part 15 of the FCCRules and with Industry Canada license-exemptRSS standard(s). Operation is subject to the fol-lowing two conditions:
(1) This device may not cause harmful interfer-ence, and
(2) This device must accept any interferencereceived, including interference that may causeundesired operation.

WARNING
Changes or modifications not expressivelyapproved by the party responsible for compli-ance could void the user's authority to oper-ate the equipment.
The term “IC:” before the radio certification num-ber only signifies that Industry Canada technicalspecifications were met.

Related information
•Driver support system radar sensor (p. 318)
Driver support system camera
The camera is used by a number of driver sup-port systems to e.g., detect a driving lane's sidemarker lines or traffic signs.
Camera location
The camera is used by the following driver sup-port systems:
•Adaptive Cruise Control (ACC)*
•Driving lane assistance*
•Driver Alert Control*
•Pilot Assist*
•City Safety
•Run-off Mitigation
•Road sign information*
•Active high beams*
Related information
•Camera limitations (p. 323)
•Adaptive Cruise Control (ACC)* (p. 281)
•Driving lane assistance (p. 350)
•Driver Alert Control (DAC) (p. 348)
•Pilot Assist* (p. 295)
•City Safety™ (p. 326)
•Run-off Mitigation (p. 355)
•Road Sign Information (RSI)* (p. 346)
•High and low beam headlights (p. 148)

DRIVER SUPPORT
}}
323
Camera limitations
The camera used by several of the driver supportsystems has certain limitations, which also affectthe systems using it.

Reduced visibility
WARNING
•The camera has the same limitations asthe human eye. In other words, its “visionis impaired” by adverse weather condi-tions such as heavy snowfall, dense fog,etc. These conditions may reduce thefunction of systems that depend on thecamera or cause these systems to tem-porarily stop functioning.
•Strong sunlight, reflections from the roadsurface, ice or snow covering the road, adirty road surface, or unclear lane markerlines may drastically reduce the camera

||
DRIVER SUPPORT
324
CauseAction
There is dirt between the inside of the windshield and the camera/radar sensor.Have the area of the windshield cleaned by a trained and qualifiedVolvo service technician.
Strong backlightingNo action required. The came will reset automatically when lightingconditions improve.

High temperatures
If the temperature in the passenger compartmentis very high, the camera and radar sensor may betemporarily turned off for approx. 15 minutesafter the engine has been started to protect theirelectronic components. When the temperaturehas cooled sufficiently, the camera and radarsensor will restart automatically.

Damaged windshield CAUTION
•Service and maintenance on City Safetymay only be carried out by a trained andqualified Volvo service technician.
•If a crack, scratch or stone chip shouldoccur in the section of the windshield infront the camera/radar sensor, contact atrained and qualified Volvo service techni-cian to repair or replace the windshield.Failing to do so may result in reducedCity Safety functionality.
•This can also result in certain functionsbeing reduced or disabled, or they mayrespond incorrectly.
To help avoid the risk of incorrect, reduced ordisabled functionality for driver support sys-tems using the camera or radar sensors:
•Volvo recommends that cracks, scratchesor stone chips on the windshield in frontof the camera/radar sensor should not
be repaired; in such cases, the entirewindshield should be replaced.
•Before the windshield is replaced, con-tact a Volvo retailer to ensure that thecorrect windshield is ordered and instal-led. If the wrong type of windshield isused, this may cause City Safety to func-tion improperly or not at all.
•Volvo recommends the use of only Genu-ine Volvo Replacement Windshields.
•When replacing windshield wipers, usethe same type or ones approved by Volvo.
After the windshield has been replaced, thecamera/radar sensor will have to be recalibra-ted by a trained and qualified Volvo servicetechnician to help ensure proper function ofall of the vehicle's camera-/radar-based sys-tems.

Maintenance
In order for camera and radar sensor to functionproperly, the area of the windshield must be kept

||
DRIVER SUPPORT
328
takes action. If the vehicle has slowed to avoidcolliding with the vehicle ahead, your speed willbe reduced to that vehicle's speed.
When auto-brake is triggered, the seat belt pre-tensioners may also be activated, see the article"Seat belts" for additional information.
Auto-braking can be cancelled if the driverpresses hard on the accelerator pedal.
When City Safety applies the brakes, the brakelights will illuminate.
When City Safety is triggered and applies thebrakes, a text message will be displayed in theinstrument panel.

Related information
•City Safety™ troubleshooting (p. 332)
•City Safety in crossing traffic (p. 331)
•City Safety limitations (p. 334)
•City Safety symbols and messages (p. 337)
•Detecting obstructions with City Safety(p. 329)
•Rear Collision Warning (RCW) (p. 338)
•City Safety warning level settings (p. 328)
•City Safety in crossing traffic (p. 331)
•Seat belts (p. 66)
•City Safety when evasive action is not possi-ble (p. 332)
City Safety warning level settings
City Safety is always activated but the function'swarning distance can be adjusted.
NOTE
City Safety cannot be turned off and activatesautomatically each time the engine/electricmotor is started.

Setting a warning level (distance)
The distance set for warnings determines thesystem's responsiveness and sets the distance atwhich visual, audible and tangible (haptic) warn-ings will be triggered.
To do so:
1.Tap Settings in the center display's Topview.
2.Tap My CarIntelliSafeCity Safety.
3.Choose among Earlier, Normal or Later.
Begin by choosing Earlier. If too many warningsare given, change to Normal.
If the driver feels that warnings are given toooften, the warning level can be lowered. Thismeans that warnings will be provided later, result-ing in fewer warnings being given.
The setting Later should only used in exceptionalcircumstances, e.g., for a more dynamic drivingstyle.
WARNING
•No automatic system can be guaranteedto function 100% correctly in all situa-tions. For that reason, never test CitySafety by driving toward a person orobject. This could result in serious injuryor death.
•Even if the setting Earlier has beenselected, warnings may be perceived asbeing given late, e.g., if the difference inspeed is great or if the vehicle aheadbrakes suddenly.
•City Safety can provide a warning for apotential collision but it can never shortenthe driver's reaction time.
•To help make City Safety as effective aspossible, always using the setting Earlieris recommended.

NOTE
•Due to local traffic regulations in certainmarkets, RCW will not activate the rearturn signals. That part of the function willbe deactivated.
•The use of the rear turn signals will alsobe deactivated if the City Safety warninglevel is set at Later. See also the section"Setting a warning level (distance)" in thearticle "City Safety settings."
•If RCW detects a vehicle approachingfrom behind, the seat belt pretensioners