2017 VOLVO XC90 TWIN ENGINE HYBRID key

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.285

Activating ACC (putting it in active
mode and setting a speed)
Before ACC can be put in active mode:
•The driver's seat belt must be buckled andthe driver's door must be closed.
•There must be a vehicle ahead (a target vehi-cle) within a reasonable distance or yourvehicle's current speed must be at least9 mph (15 km/h).
–With the symbol displayed (ACC is in
standby mode), press the button (1) onthe left-side steering wheel keypad.
>This puts ACC in active mode and setsthe vehicle's current speed, which is indi-cated by digits in the center of the speed-ometer.
The time interval to the vehi-cle ahead will only be shownwhen two vehicles are dis-played.
A speed interval will also beindicated:
•The higher speed is the one set in ACC
•The lower one is the speed of the vehicleahead (the target vehicle).

Related information
•Adaptive Cruise Control (ACC)* (p. 281)
•Setting an Adaptive Cruise Control timeinterval (p. 288)
•Deactivating/resuming Adaptive CruiseControl (ACC) (p. 285)
Deactivating/resuming AdaptiveCruise Control (ACC)
ACC can be put temporarily in standby modeand then reactivated.
Function buttons and symbols
To temporarily deactivate and put Adaptive CruiseControl in standby mode:
–Press the button (2).
>The symbol in the instrument panelwill change colors from WHITE to GRAYand the set speed in the center of thespeedometer will change from BEIGE toGRAY.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.290

WARNING
If ACC changes targets from a moving vehicleto a stationary one at speeds above 20 mph(30 km/h), the system will not react to thestationary vehicle and will accelerate to thepreviously set speed.
The driver must actively apply the brakes toslow/stop the vehicle.

Automatic standby mode when changing
targets
ACC disengages and goes into standby mode if:
•your vehicle's speed goes below approx.3 mph (5 km/h) and ACC cannot determineif the target object is a stationary vehicle orsome other type of object such as a speedbump, etc
•the vehicle's speed goes below approx.3 mph (5 km/h) and the vehicle aheadchanges lanes or turns so that ACC nolonger has a target vehicle to follow.

Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, ACC will go into standby mode and theauto-hold brake function will activate.
–The driver will then have to reactivate ACC inone of the following ways:
•Press the button on the left-sidesteering wheel keypad.
•Press the accelerator pedal.
>ACC will resume following the vehicleahead (target vehicle) if it begins to movewithin approx. 6 seconds.
NOTE
ACC can keep the vehicle at a standstill forup to 5 minutes, after which the parking brakewill be set and ACC will go into standbymode.
The parking brake has to be released beforeACC can be reactivated.

Deactivation of the auto-hold brake function
In certain situations, auto-hold will be deactivatedwhen the vehicle is at a standstill and ACC will gointo standby mode.
This means that the brakes will be released andthe vehicle can begin to roll.
The driver must actively apply the brakes to keepthe vehicle at a standstill.
This can occur in the following situations:
•the driver presses the brake pedal
•the parking brake is set
•the gear selector is moved to the P, N or Rpositions
•the driver puts ACC in standby mode.
Automatically setting the parking brake
In certain situations, the parking brake is setautomatically to help keep the vehicle at a stand-still.
This occurs if ACC keeps the vehicle at a stand-still with the brakes and:
•the driver unbuckles the seat belt or opensthe door
•ACC has kept the vehicle at a standstill formore than approx. 5 minutes
•the brakes overheat
•the engine is turned off.

Related information
•Adaptive Cruise Control (ACC)* (p. 281)
•Auto-hold brake function (p. 379)
•Parking brake (p. 382)

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.291
Adaptive Cruise Control (ACC) -troubleshooting
If this symbol is displayed in the instru-ment panel and the messageWindscreen sensor Sensorblocked, see Owner's manualappears, the ACC radar sensor is blocked andcannot detect vehicles ahead.
This message also indicates that the followingsystems may have reduced functionality:
•Distance Alert
•City Safety
•Driver Alert Control
•Pilot Assist
•Lane Keeping Aid (LKA)
•Road Sign Information (RSI)
The following table lists possible causes for this message being displayed and suitable actions:
CauseAction
The windshield in front of the radar is dirty or covered with snow/ice.Clean/clear the windshield in front of the radar.
Heavy rain or snow is interfering with the radar signals.No action possible. Heavy precipitation may affect the function of the radar.
Swirling water or snow from the surface of the road may interfere with theradar signals.No action possible. A very wet or snow-covered road surface may affect thefunction of the radar.
The windshield in front of the radar is clean but the message remains in thedisplay.Wait a short time. It may take several minutes for the radar to detect that it isno longer obstructed.
A text message can be erased by briefly pressingthe O button on the right-side steering wheelkeypad. If the message recurs, contact a trainedand authorized Volvo service technician orretailer.

Related information
•Adaptive Cruise Control (ACC)* (p. 281)

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.294
SymbolMessageExplanation
Adaptive cruise
Service required
The system is not functioning properly. Contact a trained and qualified Volvo Service tech-nician.
Windscreen sensor Sensor blocked, seeOwner's manualClean the windshield in front of the camera/radar sensor.
A text message can be erased by briefly pressingthe O button on the right-side steering wheelkeypad. If the message recurs, contact a trainedand authorized Volvo service technician orretailer.

Related information
•Adaptive Cruise Control (ACC)* (p. 281)
•Road Sign Information (RSI)* (p. 346)

DRIVER SUPPORT
}}
299

Prerequisites
The prerequisites for activating Pilot Assist are:
•The vehicle ahead must be within a reasona-ble (detectable) distance
•The camera must be able to clearly detectthe traffic lane's side marker lines
•The vehicle's speed must be under approx.30 mph (50 km/h).
A WHITE symbol indicates thatPilot Assist has been selected.
In other cases, the WHITEarrow pointing to the right indi-cates that the system is availa-ble.
A YELLOW symbol with a flashing WHITE arrowindicates that the system is about to shift intostandby mode.
With ACC in standby mode:
1.Tap ▶ (6).
>The symbol will be displayed and PilotAssist will go into standby mode.
2.Press the button (2) on the left-sidesteering wheel keypad.
>Pilot Assist will go into active mode.

WARNING
Pilot Assist is not a collision avoidance sys-tem. The driver is always responsible forsteering or applying the brakes if the systemdoes not detect another vehicle.
Do not use Pilot Assist in demanding drivingconditions such as city driving or other heavytraffic situations, in slippery conditions, whenthere is a great deal of water or slush on theroad, during heavy rain or snow, in poor visibil-ity, on winding roads or on highway on- or off-ramps.
In certain situations, it may be difficult for PilotAssist to assist the driver correctly or to deac-tivate automatically. In such cases, it is advisa-ble not to use Pilot Assist. Examples of suchsituations may be:
•the lane's side market lines are missing,badly faded or cross each other.
•the division of lanes is not clear, e.g.,when a line divides or merges withanother, at exits or if there are many roadsigns/markers.
•there are edges or other lines on or nearthe lane, e.g., curbs, cracks, repairedareas, sharp shadows, etc.
•the lane is narrow or winding.
•the lane is at the top of a hill, on anuneven road surface or over a bump.
•bad weather conditions (rain, snow, fog,slush, poor visibility, backlighting, etc).
The driver should also be aware that PilotAssist has the following limitations:
•High curbs, barriers and temporary obsta-cles (cones, barriers etc) may not bedetected or could be detected incorrectlyas side marker lines, which may create arisk of collision. The driver must ensure asafe distance to these obstacles.
•The camera or radar sensor may not beable to detect objects if there are pot-holes or if there are stationary objectspartially or completely blocking the road.
•Pilot Assist does not "see" pedestrians,animals, etc.
•Pilot Assist's steering capacity is limitedand may not always be able to help thedriver keep the vehicle in the lane.

Hands on the steering wheel
Pilot Assist only functions when the driver'shands are on the steering wheel, which is con-tinuously monitored by the system. If this is notthe case, the driver will be alerted by a text mes-sage in the instrument panel. If the driver's handsare not returned to the steering wheel, an audiblesignal will sound.
If the driver does not return his/her hands to thesteering wheel after the audible signal, PilotAssist will go into standby mode and must be
reactivated by pressing .

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.301

WARNING
•Only use a time interval that is suitable incurrent traffic conditions.
•A short time interval gives the driver lim-ited reaction time if an unexpected situa-tion occurs in traffic.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-1* (p. 295)
•Starting and activating Pilot Assist-1*(p. 298)
•Deactivating/resuming Pilot Assist-1(p. 301)
•Automatic braking with Pilot Assist-1(p. 303)
•Pilot Assist-1 limitations (p. 304)
Deactivating/resuming PilotAssist-1
Pilot Assist can be temporarily deactivated, putin standby mode and then reactivated.
Putting Pilot Assist in standby mode
Function buttons and symbols (generic illustration)
1.Press the button (2).
>Pilot Assist will go into standby mode andsymbol (8) in the instrument panel willchange from WHITE to GRAY.
2.Press the ◀ button (3).
> Pilot Assist will be turned off and shift toACC in standby mode.
or
–Press the ◀ button (3).
>Pilot Assist will be turned off and switchto ACC in active mode.
Standby mode due to driver action
If a turn signal is used or if the accelerator pedalis pressed, Pilot Assist will temporarily go intostandby mode. When the turn signal is switchedoff or the accelerator pedal is released, PilotAssist will reactivate automatically.
Automatic reactivation from standby mode can bedone within 1 minute. After 1 minute haselapsed, Pilot Assist must be reactivated man-
ually by pressing the button.
Pilot Assist will temporarily go into standby modeif:
•the brakes are applied
•the gear selector is moved to the N position.
The driver will then have to regulate speed anddistance to the vehicle ahead, or reactivate Pilot
Assist manually by pressing the button onthe left-side steering wheel keypad.

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.303
Automatic braking with PilotAssist-1
The auto-hold brakes function as follows withPilot Assist.

Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, Pilot Assist will go into standby mode andthe auto-hold brake function will activate.
–The driver will then have to reactivate PilotAssist in one of the following ways:
•Press the button on the left-sidesteering wheel keypad
•Press the accelerator pedal
>Pilot Assist will resume following the vehi-cle ahead (target vehicle) if it begins tomove within approx. 6 seconds.

NOTE
Pilot Assist can keep the vehicle at a stand-still for up to 5 minutes, after which the park-ing brake will be set and Pilot Assist will gointo standby mode.
The parking brake has to be released beforePilot Assist can be reactivated.
Deactivation of the auto-hold brake function
In certain situations, auto-hold will be deactivatedwhen the vehicle is at a standstill and Pilot Assistwill go into standby mode.
This means that the brakes will be released andthe vehicle can begin to roll.
The driver must actively apply the brakes to keepthe vehicle at a standstill.
This can occur in the following situations:
•the driver presses the brake pedal
•the parking brake is set
•the gear selector is moved to the P, N or Rpositions
•the driver puts Pilot Assist in standby mode

Automatically setting the parking brake
In certain situations, the parking brake is setautomatically to help keep the vehicle at a stand-still.
This occurs if:
•the driver unbuckles the seat belt or opensthe door
•Pilot Assist has kept the vehicle at a stand-still for more than approx. 5 minutes
•the engine is turned off
•the brakes overheat
Related information
•Pilot Assist* (p. 295)
•Pilot Assist-1* (p. 295)
•Starting and activating Pilot Assist-1*(p. 298)
•Setting a Pilot Assist-1 time interval (p. 300)
•Deactivating/resuming Pilot Assist-1(p. 301)
•Pilot Assist-1 limitations (p. 304)

DRIVER SUPPORT
}}}}
309

Prerequisites
The prerequisites for activating Pilot Assist are:
•The driver's seat belt must be buckled andthe driver's door must be closed.
•There must be a vehicle ahead (a target vehi-cle) within a reasonable distance or yourvehicle's current speed must be at least9 mph (15 km/h).
With ACC in standby mode:
1.Tap ▶ (6).
>The symbol will change to PilotAssist in standby mode (8).
2.Press the button (2) on the left-sidesteering wheel keypad.
>Pilot Assist will go into active mode andthe current speed will be stored and dis-played in the center of the speedometer.
or
If Adaptive Cruise Control has been started:
–Tap ▶ (6).
>Pilot Assist will start.
Pilot Assist's steering assis-tance is only active when thesteering wheel symbol (2)changes from GRAY to WHITE.
And Pilot Assist will only regulate the time inter-val to the vehicle ahead when a vehicle symbol(1) is displayed above the steering wheel.
At the same time, a speedinterval will be marked.
The higher speed is the onestored by the driver and thelower one is the speed of thevehicle ahead (target vehicle).

WARNING
Pilot Assist is not a collision avoidance sys-tem. The driver is always responsible forsteering or applying the brakes if the systemdoes not detect another vehicle.
Do not use Pilot Assist in demanding drivingconditions such as city driving or other heavytraffic situations, in slippery conditions, whenthere is a great deal of water or slush on theroad, during heavy rain or snow, in poor visibil-ity, on winding roads or on highway on- or off-ramps.
In certain situations, it may be difficult for PilotAssist to assist the driver correctly or to deac-tivate automatically. In such cases, it is advisa-ble not to use Pilot Assist. Examples of suchsituations may be:
•the lane's side market lines are missing,badly faded or cross each other.
•the division of lanes is not clear, e.g.,when a line divides or merges withanother, at exits or if there are many roadsigns/markers.
•there are edges or other lines on or nearthe lane, e.g., curbs, cracks, repairedareas, sharp shadows, etc.
•the lane is narrow or winding.