2017 SUBARU CROSSTREK ignition

Fuel consumption results screen
1) The average fuel consumption for the
entire driving distance, from when the
ignition switch was turned to the“ON”
position to when it was turned to the
“LOCK”/“OFF”position.
2) This display shows the average rate of
fuel consumption since the trip meter
was last reset. It displays the average
fuel consumption corresponding to the A
trip meter mileage or the one corre-
sponding to the B trip meter mileage.
&Self-check screen
When the ignition switch is turned to the
“ON”position, the vehicle self-check will
be performed. The screens corresponding
to the following items will appear one after
another for several seconds each.
1) Engine oil: Checks the interval of engine
oil replacement.
2) Oil filter: Checks the interval of oil filter
replacement.
3) Tires: Checks the interval of tire rotation.
4) Inspection and maintenance: Checks the
interval of inspection and maintenance.
When the checks are performed, the color
of the icon corresponding to the checked
item will turn green.
If there is no warning message, the self-
check will be complete without notification.
Example of notification
If there is a warning message or a
maintenance notification, the color of the
icon corresponding to the item will turn
yellow and the warning message or the
maintenance notification will be displayed.
Take the appropriate actions based on the
messages indicated.
NOTE
.The self-check screen can be set to
on or off. For details, refer to“On/Off
setting”F3-74.
.After performing the maintenance,
change the setting of the correspond-
ing maintenance item. For details, refer
to“Maintenance settings”F3-73.
.The maintenance notification screen
will be displayed under either of the
Instruments and controls/Multi function display
–CONTINUED–3-45

!Information bar
1) Information bar
2) Outside temperature indicator
3) Top display
4) Clock
While the ignition switch is in the“ACC”or
“ON”position, the outside temperature
indicator, clock, etc. will be shown on the
information bar.
!Outside temperature indicator
This displays the outside temperature
between−408F(−408C) and 1228F
(508C).
Icy road surface warning screen
When the outside temperature becomes
378F(38C) or less, the icy road surface
warning screen interrupts to inform the
driver that the road surface may be frozen.
NOTE
.The outside temperature indicator
shows the temperature around the
sensor. Therefore, the temperature in-
dication may differ from the actual
outside air temperature.
.The icy road surface warning screen
should be treated only as a guide. Be
sure to check the condition of the road
surface before driving.
.Once the icy road surface warning
screen is displayed, it will not be
displayed again unless the outsidetemperature has increased to 418F
(58C) or higher.
!Top display
One of the following items can be dis-
played on the top display.
.Average fuel consumption correspond-
ing to the driving distance of each trip
meter
.Current fuel consumption (This may
not be displayed when driving at a low
speed.)
.Driving range on remaining fuel
For details about the setting of the top
display, refer to“Top display setting”F3-
65.
NOTE
The driving range on the remaining fuel
is calculated using the average fuel
consumption of the last 19 miles (30
km) driven. This value may be different
from the values calculated using the
average fuel consumption correspond-
ing to the driving distance of each trip
meter or the current fuel consumption.
Instruments and controls/Multi function display
–CONTINUED–3-47

!EyeSight screen (models with
EyeSight system)
1) Current vehicle speed
2) Set vehicle speed
3) Preceding vehicle
4) Your vehicle
This screen displays the status of the
EyeSight system. For details, refer to the
Owner’s Manual supplement for the
EyeSight system.!Triple meter screen
Triple meter screen (display example)
This screen displays up to three optional
pieces of information that can be selected
from the following items.
The items shown in the triple meter screen
can be changed. For details, refer to
“Triple meter setting”F3-69.
Item Details
Average vehicle speed (Average
vehicle speed for the entire driving
time from when the trip meter was
reset)
Lifetime fuel consumption
Engine oil temperature
Accelerator opening ratio
Journey time (the time that has
elapsed since the ignition switch
was turned to the“ON”position) (if
equipped)
Journey distance (the distance
that has been driven since the
ignition switch was turned to the
“ON”position)
Average fuel consumption for the
entire driving distance from when
the ignition switch was turned to
the“ON”position
Boost pressure Instruments and controls/Multi function display
–CONTINUED–
3-51

Instruments and controls/Multi function display
Top menu Menu option Description Page
Maintenance
Engine Oil Set and adjust the oil maintenance notification date. 3-73
Oil Filter Set and adjust the oil filter maintenance notification date. 3-74
Tires Set and adjust the tire maintenance notification date. 3-74
Maintenance Schedule Set and adjust the vehicle maintenance notification date. 3-74
On/OffTurn on or off the self-check screen that is
activated when the ignition switch is turned to
the“ON”position.On or Off 3-74
Clear All Settings Clear all settings for maintenance items. Yes or No 3-75
Go Back Return to the top menu.—
Driving History
Set Register and overwrite the driving record. 3-76
Go Back Return to the top menu.—
Car Setting
Keyless Buzzer Volume Set the audible signal volume. 0 (OFF) to 7 3-78
Hazard Warning Flasher Set the hazard warning flasher. On or Off 3-78
Defogger Set and customize the operation of the defogger. 15 minutes or Continuous 3-79
Interior LightSet and customize the interior light off delay
timer.10, 20, 30 seconds or Off 3-81
Auto Light Sensor (if equipped)Set and customize the sensitivity of the auto
light sensor.Low, Mid, High or Max 3-82
Keyless Access Setting (if
equipped)Set and customize the keyless access function.Driver’s Door Unlock 3-83
Rear Gate Unlock 3-84
Go Back Return to top menu.—
3-54

Instruments and controls/Multi function display
&Date and time settings
The items in the date and time settings
can be set. To change the items, operate
the“
”or“”switch.
NOTE
.The“Time/Date”item must be set to
display the“Birthday”,“Anniversary”
and notifications for vehicle mainte-
nance.
.The“Birthday”and“Anniversary”
items can be entered after the“Date”
item has been set.
.Dates that do not exist in the
Gregorian calendar cannot be set (for
example, April 31).
.If your vehicle is equipped with
genuine SUBARU navigation system,
the clock of navigation system must be
set separately.
!Preparation for date setting
1. Turn the ignition switch to the“ON”
position.
2. Push and hold the
button to show
the selection screen.
3. After the selection screen is displayed,
operate the“”or“”switch to show the
“Time/Date”item. Then, push the
button.
!Current date and time setting
1. Perform the preparation steps accord-
ing to“Preparation for date setting”F3-
56.
2. Operate the“”or“”switch to
select the“Time/Date”item. Then push
the
button.
3. Select the item to set by operating the
“”or“”switch. Then push thebutton.
3-56

9. The system will notify you that the
setting is complete.
If a birthday is approaching, the following
screen will be displayed accompanied by
a beep when the ignition switch has been
turned to the“ON”position. This function
can be set to on or off. For details, refer to
“Bypass screen setting”F3-71.From 1 to 7 days prior to the birthday
On a birthday (displayed in red)
NOTE
If“__”is selected for either the
“Month”or“Day”item instead of
numbers, the birthday notification willbe deactivated.
!Anniversary setting
1. Perform the preparation steps accord-
ing to“Preparation for date setting”F3-
56.
2. Operate the“”or“”switch to
select the“Anniversary”item. Then push
the
button.
Instruments and controls/Multi function display
–CONTINUED–3-59

8. After entering the name by repeating
step 7, select“Set”by operating the“”
switch and confirm the setting by pushing
the
button.
9. The system will notify you that the
setting is complete.If an anniversary is approaching, the
following screen will be displayed accom-
panied by a beep when the ignition switch
has been turned to the“ON”position. This
function can be set to on or off. For details,
refer to“Bypass screen setting”F3-71.
From 1 to 7 days prior to the anniversary
On an anniversary (displayed in orange)
NOTE
If“__”is selected for either the
“Month”or“Day”item instead of
numbers, the anniversary notification
will be deactivated.
!Clearing birthday or anniversary
1. Perform the preparation steps accord-
ing to“Preparation for date setting”F3-56
and display“Birthday”or“Anniversary”on
the screen.
2. Select the preferred birthday/anniver-
sary.
3. When“__”is selected for either the
“Month”or“Day”item instead of numbers,
the setting of“Birthday”or“Anniversary”
will be cleared.
Instruments and controls/Multi function display
–CONTINUED–3-61

&Image quality and volume
settings
The image quality and volume settings
can be adjusted. To change the items,
operate the“
”or“”switch.
!Preparation for image quality and
volume settings
1. Turn the ignition switch to the“ON”
position.
2. Push and hold the
button to show
the selection screen.
3. After the selection screen is displayed,
operate the“”or“”switch to show the
“Display”item. Then, push thebutton.!Contrast setting
1. Perform the preparation steps accord-
ing to“Preparation for image quality and
volume settings”F3-63.
2. Operate the“”or“”switch to
select the“Contrast”item. Then push the
button.
3. Select a contrast level by operating the
“”or“”switch, and confirm the setting
by pushing thebutton.
!Screen OFF setting
1. Perform the preparation steps accord-
ing to“Preparation for image quality and
volume settings”F3-63.
Instruments and controls/Multi function display
–CONTINUED–3-63