2017 NISSAN JUKE steering

4-20Heater, air conditioner, audio and phone systems
SAA1898
3. Slowly back up the vehicle adjusting thesteering wheel so that the predictive course
lines
*Benter the parking space*C.
4. Maneuver the steering wheel to make the vehicle width guide lines
*Dparallel to the
parking space
*Cwhile referring to the
predictive course lines. 5. When the vehicle is parked in the space
completely, move the shift lever to the P
(Park) position and apply the parking brake.
How to switch the display
The Around ViewŠMonitor can display two split
views. Push the CAMERA button, change the
shift lever position, to switch between the
available views.
HOW TO ADJUST THE SCREEN VIEW
The display settings such as Display Mode,
Brightness, Contrast and Color of the Around
View
ŠMonitor can be adjusted.
1. Push the
button.
2. Touch “Settings”.
3. Touch “System” and then touch “Camera Settings”.
4. Select an item you wish to adjust.
5. Adjust the level of the setting item using the TUNE knob.
NOTE:
Do not adjust any of the display settings of
the Around View
ŠMonitor while the vehi-
cle is moving. Make sure the parking brake
is firmly applied.
AROUND VIEWŠMONITOR SYSTEM
LIMITATIONS
WARNING
Listed below are the system limitations
for Around ViewŠMonitor. Failure to
operate the vehicle in accordance with
these system limitations could result in
serious injury or death.
. Do not use the Around View
ŠMoni-
tor with the outside mirrors in the
stored position, and make sure that
the liftgate is securely closed when
operating the vehicle using the
Around View
ŠMonitor.
. The distance between objects
viewed on the Around View
ŠMoni-
tor differs from the actual distance.
. The cameras are installed above the
front grille, the outside mirrors and
above the rear license plate. Do not
put anything on the cameras.
. When washing the vehicle with
highpressure water, be sure not to
spray it around the cameras. Other-
wise, water may enter the camera
unit causing water condensation on

SAA0451
CD/USB MEMORY CARE AND
CLEANING
CD
.Handle a CD by its edges. Never touch the
surface of the disc. Do not bend the disc.
. Always place the discs in the storage case
when they are not being used.
. To clean a disc, wipe the surface from the
center to the outer edge using a clean, soft
cloth. Do not wipe the disc using a circular
motion.
Do not use a conventional record cleaner or
alcohol intended for industrial use. .
A new disc may be rough on the inner and
outer edges. Remove the rough edges by
rubbing the inner and outer edges with the
side of a pen or pencil as illustrated.
USB memory
.Do not touch the terminal portion of the USB
memory.
. Do not place heavy objects on the USB
memory.
. Do not store the USB memory in very humid
locations.
. Do not expose the USB memory to direct
sunlight.
. Do not spill any liquids on the USB memory.
Refer to the USB memory Owner’s Manual for
the details.
SAA3383
1. SOURCE select switch
2. Tuning switch
3. VOLUME control switch
STEERING WHEEL SWITCH FOR
AUDIO CONTROL
The audio system can be operated using the
controls on the steering wheel.
SOURCE select switch
Push the SOURCE select switch to change the
mode to available audio source.
Heater, air conditioner, audio and phone systems4-73

4-76Heater, air conditioner, audio and phone systems
CONNECT PHONE
To use this feature, a compatible smartphone
must be connected via BluetoothŠor USB to
the vehicle. For more information on connecting
your phone, see “Bluetooth
ŠHands-Free Phone
System (models without navigation system)”
(P.4-80) or “Bluetooth
ŠHands-Free Phone
System (models with navigation system)” (P.4-
89) .
NOTE:
. For Apple iPhones
Š, NissanConnectSM
Apps REQUIRES the phone to be
plugged in via USB.
. For Android phones, NissanConnect
SM
Apps REQUIRES the phone to be
paired via BluetoothŠ.
APPLICATION DOWNLOAD
Once connected, the NissanConnectSMApp
will search your phone to determine which
compatible applications are currently installed.
The user will then choose which apps they want
to bring into their vehicle from the list of apps
within the “Manage My Apps” section of the
NissanConnect
SMApp on their smartphone. The
vehicle will then download the in-vehicle inter-
face for each of these compatible applications.
Once downloaded, the user can access their
selected smartphone applications through the
vehicle touchscreen. For more information on application availability see NissanConnect
SM
website.
NissanConnectSMwebsite:
For U.S.
www.nissanusa.com/connect/
For Canada
www.Nissan.ca/NissanConnect (English)
www.Nissan.ca/NissanConnect/fr (French)
GENERAL INFORMATION
Apple SiriŠEyes Free personal assistant can be
accessed from the vehicle. SiriŠEyes Free can
be accessed in SiriŠEyes Free mode to reduce
user distraction. In this mode, SiriŠEyes Free is
available for interaction by voice control. After
connecting a compatible Apple device by using
Bluetooth
Š, SiriŠEyes Free can be activated
using theTALK switch on the steering
wheel.
Siri
Šis a trademark of Apple Inc., registered in
the U.S. and other countries.
INFO:
. Some Siri
ŠEyes Free functions, such as
opening apps, may not be available during
driving.
. For best results, always update your device
to the latest software version.
. Keep the interior of the vehicle as quiet as
possible. Close the windows to eliminate the
surrounding noises (traffic noises, vibration
sounds, etc.) , which may prevent the system
from recognizing the voice commands cor-
rectly.
. For functions that can be used in Siri
ŠEyes
Free, please refer to the Apple website.
SIRIŠEYES FREE

REQUIREMENTS
SiriŠis available on the iPhoneŠ4S or later.
Devices released before iPhoneŠ4S are not
supported by the SiriŠEyes Free system.
Visit www.apple.com/ios/siri for details about
device compatibility.
Siri
Šmust be enabled on the phone. Please
check phone settings.
If the device has a lock screen, Siri
Šmust be
accessible from the lock screen. Please check
phone settings.
For best results, always update your device to
the latest software version.
SAA3385
SIRIŠEYES FREE ACTIVATION
SiriŠEyes Free function can be activated by
using theTALK switch on the steering
wheel.
Models with navigation system
1. Connect a Siri
ŠEyes Free enabled iPhoneŠ
to the vehicle. (See “Connecting procedure”
(P.4-92) .)
2. After the Bluetooth
Šconnection is estab-
lished, push and hold theTALK switch
to activate the SiriŠEyes Free function.
Models without navigation system
1. Connect a Siri
ŠEyes Free enabled iPhoneŠ
to the vehicle. (See “Initialization” (P.4-83) .) 2. After the Bluetooth
Šconnection is estab-
lished, the switch operation select screen is
displayed.
3. Select “Short Press” or “Long Press” for Siri
ŠEyes Free activation. Switch action can
also be changed from the BluetoothŠ
settings menu. (See “Changing SiriŠEyes
Free Settings (models without navigation
system)” (P.4-78) .)
OPERATING SIRIŠEYES FREE
1. Push or push and hold theTALK switch.
2. Speak your command and then listen to the Siri
ŠEyes Free reply.
After starting SiriŠEyes Free, push theTALK switch again within 5 seconds of the end
of the SiriŠEyes Free announcement to extend
the session.
Example 1 - Playing music
1. Push or push and hold the
TALK switch.
2. Say “Play (artist name, song name, etc.)”.
3. Your vehicle will automatically change to Bluetooth
ŠAudio or iPodŠmode* when the
music starts playing. Mode selection is
determined by the phone.
*: If the iPhone
Šis also connected with the
USB cable.
If the audio track does not start playing
Heater, air conditioner, audio and phone systems4-77

TROUBLESHOOTING GUIDE
SymptomCause and Countermeasure
Cannot access SiriŠEyes Free from the switch on the steering wheel Check if a BluetoothŠconnection is established between the iPhoneŠand the system.
Check if SiriŠis enabled on the device. On your phone, go to SiriŠsetting.
Check that SiriŠcan be accessed from the device lock screen. This can be set in the settings menu
of your phone.
Models without navigation system:
Check the settings for Siri
ŠEyes Free activation on the vehicle audio system. If the setting is “Long
Press”, you must push and hold theTALK switch on the steering wheel for more than 1.5
seconds to start SiriŠEyes Free. If the setting is “Short Press”, a short push and release of the switch
should start SiriŠEyes Free.
Audio source does not change automatically to iPodŠor BluetoothŠ
Audio mode For best results, use the native music app. Performance of music control function while using
Podcasts, Audiobook or other 3rd party music apps may vary.
For best results, play media already stored on your device. Streaming music or playback from cloud
storage may degrade performance.
Switch the source manually by pushing the AUX or MEDIA button on the vehicle audio system or the
SOURCE select switch on the steering wheel.
Play, pause, next track, previous track or play timer does not work For best results, use the native music app. Performance of music control function while using Podcasts, Audiobook or other 3rd party music apps may vary and is controlled by the device.
Cannot hear any music/audio being played back from a connected
iPhone
ŠCheck that the audio source is set to BluetoothŠAudio or iPodŠmode. A USB connection is
required for iPodŠmode.
Cannot hear map turn-by-turn direction guidance from a connected
iPhone
ŠCheck that the audio source is set to BluetoothŠAudio or iPodŠmode. A USB connection is
required for iPodŠmode.
Cannot receive text message notifications on the vehicle audio
system Check if “Show Notifications” is enabled on your phone. On your phone, go to BluetoothŠsettings.
Find the device name, like “My Car”. Tapon your phone. Turn on “Show Notifications”.
Cannot reply to text message notifications using SiriŠEyes Free After receiving an incoming text message, follow the on-screen guidance. Push or push and hold theTALK switch on the steering wheel for SiriŠEyes Free. After SiriŠEyes Free starts, say “Text
Message”.
Heater, air conditioner, audio and phone systems4-79

4-82Heater, air conditioner, audio and phone systems
IC Regulatory information
.Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the
device.
. This Class B digital apparatus meets all
requirements of the Canadian Interference-
Causing Equipment Regulations.
BluetoothŠtrademark
BluetoothŠis a trademark owned
by Bluetooth SIG, Inc., and
licensed to Visteon Corporation.
USING THE SYSTEM
The voice recognition system allows hands-free
operation of the BluetoothŠPhone System.
If the vehicle is in motion, some commands may
not be available so full attention may be given to
vehicle operation.
SAA3385
Control buttons and microphone
The control buttons for the BluetoothŠHands-
Free Phone System are located on the steering
wheel.
PHONE SEND:
Push the
button to initiate a VR session or
answer an incoming call.
INFO:
If the “Siri” on the Bluetooth
Šsettings menu is
set to “Short Press”, pushing and holding the
PHONE SEND button initiates a VR
session for Hands-Free Phone operation. (See
“Bluetooth
Šsettings” (P.4-88).) You can also use the
button to interrupt the
system feedback and give a command at once.
See “List of voice commands” and “During a
call” in this section for more information.
PHONE END:
While the voice recognition system is active,
push and hold the
button to quit the voice
recognition system at any time.
Microphone:
Microphone is located near the map lights.
Manual control:
While using the Voice Recognition system, it is
possible to select menu options by using the
steering wheel controls instead of speaking
voice commands. To activate manual control
mode, push the
button on the steering
wheel to access the phone menu and then tilt
the tuning switch (
or) up or down.
The manual control mode does not allow dialing
a phone number by digits. The user may select
an entry from the Phonebook or Recent Calls
lists. To reactivate Voice Recognition, exit the
manual control mode by pushing and holding the
button. At that time, pushing thebutton
will start the Hands-Free Phone System.

Choosing a language
You can interact with the BluetoothŠHands-
Free Phone System using several languages
that are available. For operations to change the
language, see “Audio main operation” (P.4-45)
or “Audio main operation” (P.4-54) .
Changing voice feedback volume
If you want to adjust the volume of the voice
feedback, push the volume control switch on the
steering wheel while being provided with feed-
back. You can also use the VOL (volume) control
knob on the audio unit.
Initialization
When the ignition switch is placed in the ACC
or ON position, voice recognition is initialized,
which takes a few seconds. If the
button is
pushed before the initialization completes, the
system will announce “Hands-free phone sys-
tem not ready” and will not react to voice
commands. Connecting procedure:
NOTE:
The connecting procedure must be per-
formed when the vehicle is stationary. If
the vehicle starts moving during the pro-
cedure, the procedure will be cancelled.
You can register up to 5 different Bluetooth
Š
cellular phones in the in-vehicle phone module.
However, you can talk on only one cellular phone
at a time.
To connect a phone to the Bluetooth
ŠHands-
Free Phone System;
1. Push the ENTER/SETTING button.
2. Use the TUNE·FOLDER or TUNE·SCROLL control knob to select “Bluetooth” and then
push the ENTER/SETTING button.
3. Select “Add Phone” and then push the ENTER/SETTING button.
4. When a message with a PIN appears on the screen, operate the Bluetooth
Šphone to
enter the PIN.
The connecting procedure varies according to
each phone. See the phone’s Owner’s Manual
for details.
Giving voice commands
To operate voice recognition, push and release
thebutton located on the steering wheel.
After the tone sounds, speak a command.
The command given is picked up by the
microphone, and voice feedback is given when
the command is accepted.
. If you need to hear the available commands
for the current menu again, say “Help” and
the system will repeat them.
. If a command is not recognized, the system
announces, “Command not recognized.
Please try again.” Make sure the command
is said exactly as prompted by the system
and repeat the command in a clear voice.
. If you want to go back to the previous
command, you can say “Go back” any time
the system is waiting for a response.
. You can cancel a command when the
system is waiting for a response by saying,
“Cancel” or “Quit.” The system announces
“Cancel” and ends the VR session. You can
also push and hold the
button on the
steering wheel at any time to end the VR
session. Whenever the VR session is
cancelled, a double beep is played to
indicate you have exited the system.
Heater, air conditioner, audio and phone systems4-83

4-84Heater, air conditioner, audio and phone systems
.If you want to adjust the volume of the voice
feedback, push the (-or+) button
on the steering wheel while being provided
with feedback. You can also use the radio
volume control knob.
Voice Prompt Interrupt:
In most cases you can interrupt the voice
feedback to speak the next command by
pushing the
button on the steering wheel.
After interrupting the system, wait for a beep
before speaking your command.
One Shot Call:
To use the system faster, you may speak the
second level commands with the main menu
command on the main menu. For example, push
the
button and after the tone say, “Call
Redial”.
Operating tips:
To get the best performance out of the voice
recognition system, observe the following:
. Keep the interior of the vehicle as quiet as
possible. Close the windows to eliminate
surrounding noises (traffic noises, vibration
sounds, etc.) , which may prevent the system
from recognizing voice commands correctly.
. Wait until the tone sounds before speaking a
command. Otherwise, the command will not
be received properly. .
Start speaking a command within 5 seconds
after the tone sounds.
. Speak in a natural voice without pausing
between words.
Voice commands
Voice commands can be used to operate the
BluetoothŠHands-Free Phone System. Push
thebutton and say “Phone” to bring up the
phone command menu. The available options
are:
. Call
. Phonebook
. Recent Calls
. Show Applications
. Messaging
. Select Phone
Call:
For more information on the “Call” command,
see “Making a call” (P.4-85).
Phonebook:
The following commands are available under
“Phonebook”:
. (A Name)
Say a name in the phonebook to bring up a
list of options for that phonebook entry. The
system will say the name it interpreted
based on the voice command provided. If the name is incorrect, say “Correction” to
hear another name.
Once the correct phonebook entry is
identified, say “Dial” to dial the number or
“Send Text” to send a text message to that
number. Say “Record Name” to record a
name for the phonebook entry. Say “Delete
Recording” to delete a recorded name for
the phonebook entry.
. List Names
Speak this command to have the system list
the names in the phonebook one by one
alphabetically. Say “Dial” to dial the number
of the current name or “Send Text” to send a
text message to that number. Say “Next
Entry” or “Previous Entry” to move through
the list alphabetically. Say “Record Name” to
record a name for the current phonebook
entry. Say “Delete Recording” to delete a
recorded name for the current phonebook
entry.
. Delete Entry
Speak this command to delete an entry in
the phonebook. Choose an entry to delete
by speaking the desired name or say “List
Names”.