2017 MITSUBISHI SHOGUN instrument cluster

NOTElThe lamp auto-cutout will not function when
the lamp switch is in the “” position
l When the ignition key has been turned to ei-
ther the “LOCK” or “ACC” position or re- moved from the ignition switch with the
lamp switch in the “
” position, and the
lamp switch is returned to the “OFF” within
approximately 3 minutes, the auto-cutout function will not be activated.
When you want to keep the
lamps on
l Turn the lamp switch in the “OFF” posi-
tion while the ignition switch is in the
“LOCK” or “ACC” position.
l Turn on the lamps with the switch in the
“
” or “” position again, then the
lamps will remain on.
l Remove the ignition key.
NOTElFor further information, we recommend you
to consult a MITSUBISHI MOTORS Au-
thorized Service Point.Lamp monitor buzzer
E00506100256
If the driver’s door is opened when the key is
in the “LOCK” or “ACC” position or re-
moved from the ignition switch while the
lamps are on, a buzzer will sound to remind the driver to turn off the lamps.
When the lamp auto-cutout function acts, the
buzzer will stop automatically.
Dipper (High/Low beam
change)
E00506201586
When the lamp switch is in the “” posi-
tion, the beam changes from high to low (or
low to high) each time the lever is pulled fully (1). While the high-beam is on, the
high-beam indication lamp in the instrument
cluster will also illuminate.
NOTEl On vehicles equipped with the automatic
high-beam system, if you press the ON side
of the automatic high-beam system switch when high-beam is on, automatic high-beam
system will be activated.Automatic high-beam system*
E00538200074
The system switches the headlamp beams
(high/low) when the automatic high-beam system camera (A) senses a illuminant such as lights of a vehicle in front or oncoming ve-
hicle or a street lamp.
Combination headlamps and dipper switch
5-36OVWX17E1Instruments and controls5

NOTE•It becomes dark and bright suddenly and
continuously around your vehicle.
• Your vehicle is driven on uneven surfa-
ces.
• Your vehicle is driven on a winding road.
• A reflective object such as a noticeboard
or a mirror reflects a light ahead of yourvehicle
• The rear end of a vehicle in front (such as
a container truck) reflect a strong light.
• Your vehicle’s headlamp is broken or
dirty.
• Your vehicle is inclined due to a flat tyre
or towing.
• The automatic high-beam system warning
lamp comes on.
l Observe the precautions below to maintain
good usage conditions:
• Do not touch the camera lens.
• Do not subject the inside rear view mirror
and the camera to strong impact. Do not spill any liquid over them.
• Do not attempt to disassemble the camera.
• Do not affix a sticker or label on the
windscreen near the camera.
• Do not place any objects on the instru-
ment panel.
• Do no hang any accessories around the in-
side rear view mirror or the camera.
• Avoid overload.
• Do not modify your vehicle.
• When the windscreen is replaced, use the
MITSUBISHI MOTORS genuine parts.Automatic high-beam system
warning lamp
E00538300046
The automatic high-beam system warning
lamp (yellow) will illuminate when the auto-
matic high-beam system detects any fault when the ignition switch is in the “ON” posi-
tion.
CAUTIONl If the warning lamp comes on, we recom-
mend you to have the system checked.NOTEl If the warning lamp comes on, press the
OFF side (2) on the automatic high-beam
system switch to deactivate the system. It is the responsibility of the driver to switch theheadlamp beams (high/low) manually to suit
each driving condition.
Refer to “Dipper (High/Low beam change)”
on page 5-36.Headlamp flasher
E00506300128
The high-beams flash when the lever is
pulled slightly (2), and will go off when it is
released.
When the high-beam is on, the high-beam in- dication lamp in the instrument cluster will il-
luminate.
NOTEl The high-beams can also flash when the
lamp switch is OFF.
l If you turn the lamps off with the headlamps
set to high-beam, the headlamps are auto- matically returned to their low-beam setting
when the lamp switch is next turned to the
“
” position.
Combination headlamps and dipper switch
5-39OVWX17E1Instruments and controls5

Automatic headlamp levellingwarning lamp
E00525901045
The automatic headlamp levelling warning
lamp should illuminate when the ignition switch is turned “ON”, and should go off in a
few seconds.
CAUTIONl If the warning lamp stays on or does not illu-
minate when the ignition switch is turned
“ON”, it indicates that the automatic head- lamp levelling device is not functioning.
We recommend you to have your vehicle in- spected.Turn-signal lever
E00506500928
1- Turn-signalsWhen making a normal turn, use posi-
tion (1). The lever will return automati-
cally when cornering is completed.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when released.
Also, when you move the lever to (2)
slightly then release it, the turn-signal
lamps and indication lamp in the instru-
ment cluster will flash 3 times.
NOTEl If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned out. We recommend you to have the vehicle
inspected.NOTEl It is possible to activate the following func-
tions. For further information, we recom- mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
• Sounding of a buzzer as the turn-signal
lamps flash.
• Flashing of the turn-signal lamps when
the lever is operated with the ignition switch in the “ACC” position.
• The turn-signal lamps 3-flash function for
lane changes can be deactivated.
• The time required to operate the lever for
the 3-flash function can be adjusted.Hazard warning flasher
switch E00506600440
Use the hazard warning flasher switch when
the vehicle has to be parked on the road for
any emergency.
The hazard warning flashers can always be operated, regardless of the position of the ig-
nition key.

Push the switch to turn on the hazard warning flashers, all turn-signal lamps flash continu-
ously.
Turn-signal lever
5-42OVWX17E1Instruments and controls5

To turn them off, push the switch again.NOTElIt is possible for a buzzer to sound with
flashing of the turn-signal lamps. For further information, we recommend you to consult aMITSUBISHI MOTORS Authorized Serv-
ice Point.Fog lamp switch
E00506700047Front fog lamp switch*
E00508301839
The front fog lamps illuminate only when theheadlamps or tail lamps are on. Push the
switch to turn on the front fog lamps, and push the switch again to turn them off.
The indication lamp in the instrument cluster
will illuminate while the front fog lamps are
on.LHDRHD
NOTEl The front fog lamps are automatically turned
off when the headlamps or tail lamps are turned off. To turn on the front fog lamps again, push the switch again when the head-
lamps or tail lamps turn on.
l Do not use fog lamps except in conditions of
fog, otherwise excessive lamp glare may temporarily blind oncoming vehicle drivers.Rear fog lamp switch
E00508401856
The rear fog lamp illuminates only when the
headlamps or front fog lamps (if so equipped)
are on.
Push the switch to turn on the rear fog lamp, and push the switch again to turn it off.
The indication lamp in the instrument cluster
will illuminate while the rear fog lamp is on.
Type 1
Fog lamp switch
5-43OVWX17E1Instruments and controls5