2017 MITSUBISHI SHOGUN tow

WARNINGlBe sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.NOTEl The chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if needed.
l If chocks are not available, use stones or any
other objects that are large enough to hold the wheel in position.
6. Get the spare wheel, jack, jack handle
and wheel nut wrench ready.
Refer to “Tool, jack and jack handle” on page 8-07.
Spare wheel information
E00803600266
Check the air pressure of the spare tyre fre-quently and make sure it is ready for emer-
gency use at any time.
Maintaining the spare wheel at the highest specified air pressure will ensure that it can
always be used under any conditions (city/ high-speed driving, varying load weight,etc.).
The spare wheel is stored on the outside of
the backdoor. (Refer to “To remove the spare wheel” on page 8-10).
1- Spare wheel
CAUTIONl The tyre pressure should be periodically
checked and maintained at the specified
pressure while the tyre is stowed.
Driving with an insufficient tyre pressure can lead to an accident. If you have nochoice but to drive with an insufficient tyre
pressure, keep your speed down and inflate the tyre to the correct pressure as soon as
possible. (Refer to “Tyre inflation pressures”
on page 10-11.)To remove the spare wheel
E00803500177
CAUTIONl Grasp the spare wheel firmly when remov-
ing or attaching it.
l When removing the spare wheel, put on
gloves. Removing the spare wheel with your
bare hands may cause injury to the fingers.
1. Open the backdoor.
2. Open the lids (A) inside of the backdoor.
How to change a tyre
8-10OVWX17E1For emergencies8

TowingE00801505888
If your vehicle needs to be tow- ed
If towing is necessary, we recommend you to have it done by your MITSUBISHI
MOTORS Authorized Service Point or a
commercial tow truck service.

In the following cases, transport the vehicle
using a tow truck.
l The engine runs but the vehicle does not
move or abnormal noise is produced.
l Inspection of the vehicle’s underside re-
veals that oil or some other fluid is leak- ing.
If a wheel gets stuck in a ditch, do not try to tow the vehicle. Please contact your author-
ized MITSUBISHI MOTORS dealer or a
commercial tow truck service for assistance.

Only when you cannot receive a towing serv-
ice from a MITSUBISHI MOTORS Author-
ized Service Point or commercial tow truck service, tow your vehicle carefully in accord-
ance with the instructions given in “Emer- gency towing” in this part.

The regulations concerning towing may dif-
fer from country to country. It is recommen-
ded that you obey the regulations of the area where you are driving your vehicle.Towing the vehicle by a tow
truckCAUTIONl This vehicle must not be towed by a tow
truck using sling lift type equipment (Type A) as illustrated. Using a sling lift will dam-age the bumper and front end.
l Be sure to shift the transfer shift lever to
“2H” position and transport the vehicle with the driving wheels on a carriage (Type C, D
or E) as illustrated. Never try to tow with the transfer shift lever in “4H”, “4HLc” or “4LLc” positions and with the front or rearwheels on the ground (Type B or Type C) as illustrated. This could result in driving sys-
tem damage or the vehicle may jump at the
carriage. If you cannot shift the transfer shift lever to the “2H” position or the transmis-sion is malfunctioning or damaged, transport the vehicle with all wheels on a carriage
(Type D or E) as illustrated.
l As your vehicle equipped with the Active
Stability & Traction Control system (ASTC), if the vehicle is towed with the ig-
nition switch in the “ON” position and only
the front wheels or only the rear wheels raised off the ground, the active Traction
Control System may operate, resulting in an accident.
Towing
8-16OVWX17E1For emergencies8

CAUTIONlIf you tow the vehicles with the driving
wheels on the ground (Type B) as illustrated,
make sure that the towing speed and dis-
tance given below are never exceeded, caus-
ing damage to the transmission.

Petrol-powered vehicles
Towing speed: 50 km/h (31 mph)
Towing distance: 50 km (31 miles)

Diesel-powered vehicles
Towing speed: 30 km/h (19 mph)
Towing distance: 80 km (50 miles)

For the towing speed and the towing dis- tance, follow the local driving laws and reg- ulations.
Towing with front wheels off
the ground (Type B)
Place the selector lever in the “N” (NEU-TRAL) position.
Release the parking brake.
CAUTIONl Never tow an
A/T vehicle with the front
wheels up (and the rear wheels on the
ground) (Type B) when the A/T fluid level is low. This may cause serious and expensive damage to the transmission.Towing with rear wheels off the
ground (Type C)
Place the selector lever in the “N” (NEU- TRAL) position. Turn the ignition key to the
“ACC” position and secure the steering wheel in a straight-ahead position with a ropeor tiedown strap. Never place the ignition
switch in the “LOCK” position when towing.
Emergency towing
If towing service is not available in an emer-gency, your vehicle may be temporarily tow-ed by a rope secured to the towing hook.If your vehicle is to be towed by another ve-
hicle or if your vehicle tows another vehicle, pay careful attention to the following points:
If your vehicle is to be towed by
another vehicle
1. The front towing hooks (A) and rear
towing hooks (B) are located as shown
in the illustrations. Secure the tow rope
to the towing hook.
Rear
NOTEl Using a wire rope or metal chain can result
in damage to the vehicle body. It is best to use a non-metallic rope. If you use a wire
rope or metal chain, wrap it with cloth at any
point where it touches the vehicle body.
l Take care that the tow rope is kept as hori-
zontal as possible. An angled tow rope can
damage the vehicle body.
Towing
8-17OVWX17E1For emergencies8 Front

NOTElSecure the tow rope to the same side towing
hook, to keep the tow rope as straight as pos-
sible.
2. Keep the engine running.
If the engine is not running, turn the ig-
nition switch to the “ACC” or “ON” po- sition to unlock the steering wheel.
CAUTIONl When the engine is not running, the brake
booster and power steering pump do not op- erate. This means higher brake depression
force and higher steering effort are required. Therefore, vehicle operation is more difficult
than usual.
l Do not leave the key in the “LOCK” posi-
tion. The steering wheel will lock, causing
loss of control.
3. Place the selector lever in the “N”
(NEUTRAL) position.
4. Shift the transfer shift lever to “2H” po-
sition.
5. Turn on the hazard warning lamps if re-
quired by law. (Follow the local driving
laws and regulations.)
6. During towing make sure that close con-
tact is maintained between the drivers of
both vehicles, and that the vehicles trav- el at low speed.
CAUTIONl Avoid sudden braking, sudden acceleration
and sharp turning; such operation could
cause damage to the towing hooks or the tow
rope.
People in the vicinity could be injured as a
result.
l When towing or being towed down a long
slope, the brakes may overheat reducing the effectiveness. In this situation, have your ve-hicle transported by a tow truck.
l When the vehicle is to be towed by another
vehicle with all the wheels on the ground,make sure that the towing speed and dis-
tance given below are never exceeded,
avoiding damage to the transmission.

Petrol-powered vehicles
Towing speed: 50 km/h (31 mph)
Towing distance: 50 km (31 miles)

Diesel-powered vehicles
Towing speed: 30 km/h (19 mph)
Towing distance: 80 km (50 miles)

For the towing speed and the towing dis- tance, follow the local driving laws and reg- ulations.If your vehicle tows another ve-
hicle
Only use the rear towing hook as shown in
the illustration. Secure the tow rope to the rear towing hook.
CAUTIONl When you are going to tow another vehicle,
move the transfer shift lever to “4H” posi-
tion.
Selecting “2H” drive may increase the dif- ferential oil temperature, resulting in possi-
ble damage to the driving system.
Further, the drive train will be subjected to
excessive loading possibly leading to oil leakage, component seizure, or other serious faults.
Towing
8-18OVWX17E1For emergencies8

NOTElDo not tow a vehicle heavier than your own
vehicle.Operation under adverse
driving conditions E00801704160
If your vehicle becomes stuck
in sand, mud or snow
If the vehicle becomes stuck in snow, sand,
or mud, it can often be moved with a rocking
motion. Move the selector lever alternately
between the Sports mode and “R” (RE- VERSE) position, while applying slight pres-sure to the accelerator pedal.
Avoid racing the engine or spinning the
wheels. Prolonged efforts to free a stuck ve-hicle may result in overheating, transmission
and drivetrain failure. Allow the engine to idle for a few minutes to let the transmissioncool between rocking attempts.
If the vehicle remains stuck after several rocking attempts, seek other assistance.WARNINGl When attempting to rock your vehicle out
of a stuck position, be sure that the area around the vehicle is clear of people and
physical objects. The rocking motion may cause the vehicle to suddenly launch for-ward or backward, causing injury or
damage to nearby people or objects.
On a flooded road
l Avoid flooded roads. In the event driv-
ing flooded roads, doing so may causethe following serious damage to the ve-
hicle. • Engine stalling
• Short in electrical components
• Engine damage caused by water im-
mersion
After driving on flooded roads, be sure
to have an inspection at an Authorized MITSUBISHI MOTORS dealer and takethe necessary measures or repair.
l When driving in rain, or water-covered
roads, or through a car wash, water could enter the brake discs, resulting in
temporarily ineffective brakes.
In such cases, lightly depress the brake
pedal to see if the brakes operate proper- ly. If they do not, lightly depress the pedal several times while driving in or-
der to dry the brake pads.
l When driving in rain or on a road with
many puddles a layer of water may form
between the tyres and the road surface.
This reduces a tyre’s frictional resistance
on the road, resulting in loss of steering
stability and braking capability.

To cope with this, observe the following items: (a)Drive your vehicle at slow
speed. (b)Do not drive on worn tyres. (c)Always maintain the specified
tyre inflation pressures.
On a snow-covered or frozen
road
l When driving on a snow-covered or fro-
zen road, it is recommended that you use snow tyres or tyre chains.
Operation under adverse driving conditions
8-19OVWX17E1For emergencies8

WARNINGlAs with any vehicle, do not park or oper-
ate this vehicle in areas where combusti-
ble materials such as dry grass or leaves
can come in contact with a hot exhaust since a fire could occur.
l Paint should not be applied to the catalyt-
ic converter.NOTEl In case of the petrol-powered vehicles, use
UNLEADED PETROL ONLY of the typerecommended in “Fuel selection” on page
2-02.Bonnet
E01000304445
To open
1. Pull the release lever towards you to un-
lock the bonnet.
LHDRHD
2. Raise the bonnet while pressing the safe-
ty lock.
NOTEl Only open the bonnet when the wipers are in
the original position. Failure to do so maycause damage to the bonnet, wiper arms or
windscreen.
3. Support the bonnet by inserting the sup-
port bar in its slot.
Bonnet
10-03OVWX17E1Maintenance10

CAUTIONlDo not bring nearby parts, plastic parts and
so on into contact with sulphuric acid (bat-
tery electrolyte) which may crack, stain or discolour them.
If they are in contact, wipe off with soft
cloth, chamois or the like and an aqueous solution of neutral detergent then immedi-
ately rinse the affected parts with plenty of
water.NOTEl Keep the terminals clean. After the battery is
connected, apply terminal protection grease.
To clean the terminals, use lukewarm water.
l Check to see if the battery is securely instal-
led and cannot be moved during travel. Also check each terminal for tightness.
l When the vehicle is to be left unused for a
long period of time, remove the battery and
store it in a place where the battery fluid will not freeze. The battery should be stored only in a fully charged condition.Tyres
E01001300239WARNINGlDriving with tyres that are worn, dam-
aged or improperly inflated can lead to a
loss of control or blow out of the tyres which can result in a collision with serious
or fatal injury.Tyre inflation pressures
E01001404254
Except for vehicles for Russia, Kazakhstan, Belarus and UkraineTyre sizeUp to 5 passengersUp to max. loadAt trailer towingFrontRearFrontRearFrontRear265/65R17 112H2.2 bar (220 kPa)2.4 bar (240 kPa)2.4 bar (240 kPa)2.8 bar (280 kPa)2.6 bar (260 kPa)3.0 bar (300 kPa)265/65R17 112S2.4 bar (240 kPa)2.6 bar (260 kPa)2.6 bar (260 kPa)3.0 bar (300 kPa)2.6 bar (260 kPa)3.0 bar (300 kPa)265/60R18 110H2.2 bar (220 kPa)2.4 bar (240 kPa)2.4 bar (240 kPa)2.8 bar (280 kPa)2.6 bar (260 kPa)
3.2 bar (320 kPa) *3.0 bar (300 kPa)
3.5 bar (350 kPa) **
: 5 door models
Tyres
10-11OVWX17E1Maintenance10

Vehicles for Russia, Kazakhstan, Belarus and UkraineTyre sizeUp to 5 passengersUp to max. loadAt trailer towingFrontRearFrontRearFrontRear265/65R17 112H2.0 bar (200 kPa) *
2.2 bar (220 kPa)2.2 bar (220 kPa) *
2.4 bar (240 kPa)2.4 bar (240 kPa)2.8 bar (280 kPa)2.6 bar (260 kPa)3.0 bar (300 kPa)265/60R18 110H2.0 bar (200 kPa) *
2.2 bar (220 kPa)2.2 bar (220 kPa) *
2.4 bar (240 kPa)2.4 bar (240 kPa)2.8 bar (280 kPa)2.6 bar (260 kPa)3.0 bar (300 kPa)* : Vehicles for 3000 models
Check the tyre inflation pressure of all the tyres while they are cold; if insufficient or excessive, adjust to the specified value.
After the tyre inflation pressure has been adjusted, check the tyres for damage and air leaks. Be sure to put caps on the valves.

Wheel condition
E01001800478
1- Location of the tread wear indicator
2- Tread wear indicator
Check the tyres for cuts, cracks and other
damage. Replace the tyres if there are deep
cuts or cracks. Also check each tyre for pieces of metal or pebbles.
The use of worn tyres can be very dangerous
because of the greater chance of skidding or
hydroplaning. The tread depth of the tyres
must exceed 1.6 mm in order for the tyres to meet the minimum requirement for use.
Tread wear indicators will appear on the sur-
face of the tyre as the tyre wears, thereby in-
dicating that the tyre no longer meets the
minimum requirement for use. When these
wear indicators appear, the tyres must be re-
placed with new ones.
When replacement of any of the tyres is nec- essary, replace all of them.CAUTIONl Always use tyres of the same size, same
type, and same brand, and which have no wear differences.
Using tyres of different size, type, brands or
degree of wear, will increase the differential
oil temperature, resulting in possible damage to the driving system. Further, the drive train
will be subjected to excessive loading, possi- bly leading to oil leakage, component seiz-ure, or other serious faults.
Tyres
10-12OVWX17E1Maintenance10