2017 MITSUBISHI SHOGUN tow

NOTElStowing the head restraints with their front
faces facing downward would prevent the
third seat from being stowed.
3. Pull up knob (C) on the side of the seat-
back, then tilt the seatback forward.
4. Push lever (D) forward, then tilt the seat-
back forward until the seatback touches
the seat cushion.CAUTIONl Do not drive with luggage placed on the for-
ward-folded seatback.
5. Pull lever (E), fold the seat backward,
and store it into the luggage floor box.
CAUTIONl Ensure that lever (E) is not operated while
the seat is occupied. The folding action of
the seat in such a situation could result in an unexpected accident.
l When folding the seat, be sure not to catch
your hands between seat and luggage floor box.
l When folding the seat away into the luggage
floor box, hold the seat by hand and fold it
slowly. If the seat is not held properly, it might fall under its own weight during fold-
ing and pinch your hand.
Making a luggage area
4-16OVWX17E1Seat and seat belts4

3.Push lever (B) forward, then tilt the seat-
back forward until the seatback touches
the seat cushion.
4. Pull the seat lock lever (C).
5. Fold the stands (D) towards you from
the seat side, while lifting the front end
of the seat.
6. Put down the front end of the seat to the
floor. In this situation, the seat locking system is unlocked automatically.
7. Remove the covers (E) by turning the
knobs (F) anticlockwise.
G- Unlock
H- Lock
Making a luggage area
4-18OVWX17E1Seat and seat belts4

WARNINGlAlways place the shoulder belt over your
shoulder and across your chest. Never put it behind you or under your arm.
l One seat belt should be used by only one
person. Doing otherwise can be danger-
ous.
l The seat belt will provide its wearer with
maximum protection if the recliner seat- back is placed in fully upright position.
When the seatback is reclined, there is
greater risk that the passenger will slide under the belt, especially in a forward im-
pact accident, and may be injured by the
belt or by striking the instrument panel or seatbacks.
l Seat belts should always be worn by every
adult who drives or rides in this vehicle, and by all children who are tall enough towear seat belts properly.
Other children should always use proper child restraint systems.
l Remove any twists when using the belt.
l No modifications or additions should be
made by the user which will either pre- vent the seat belt adjusting devices fromoperating to remove slack, or prevent the
seat belt assembly from being adjusted to
remove slack.
l Never hold a child in your arms or on
your lap when riding in this vehicle, even
if you are wearing your seat belt. To do so risks severe or fatal injury to the child in
a collision or sudden stop.
l Always adjust the belt to a snug fit.WARNINGlAlways wear the lap portion of the belt
over your hips.3-point type seat belt (with
emergency locking mechanism)
E00404902934
This type of belt requires no length adjust- ment. Once worn, the belt adjusts itself to the
movement of the wearer, but in the event of a sudden or strong shock, the belt automatical-
ly locks to hold the wearer’s body.
NOTEl You can check if the belt locks by pulling it
forward quickly.
To fasten
1. Pull the seat belt out slowly while hold-
ing the latch plate.
NOTEl When the seat belts cannot be pulled out in a
locked condition, pull the belts once force-
fully and then return them. After that, pull
the belts out slowly once again.
2. Insert the latch plate into the buckle until
a “click” is heard.
WARNINGl Never wear the lap portion of the belt
across your abdomen. During accidents it
can press sharply against the abdomen and increase the risk of injury.
l The seat belts must not be twisted when
worn.
3. Pull the belt slightly to adjust slackness
as desired.
Seat belts
4-22OVWX17E1Seat and seat belts4

To unfasten
Hold the latch plate and push the button on
the buckle.
NOTEl As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could damage the vehicle.
l If the seat belt (A) or ring (B) becomes dirty,
the belt may not retract smoothly. If the seat belt and ring are dirty, clean them with a
mild soap or detergent solution.NOTESeat belt reminder/warning
lamp
E00409800338
The seat belt warning lamp is located on the instrument panel. A tone and warning lamp
are used to remind the driver to fasten the seat belt.
When the ignition key is turned to the “ON”
position, the warning lamp will come on and
a tone will sound for about 6 seconds. If the
driver’s seat belt remains unfastened for ap-
proximately 1 minute later, the warning lamp will flash and the tone sound intermittently
(each 12 times) when the vehicle is driven. If the driver subsequently unfastens the seat belt while driving, the warning lamp and tone
will issue further warnings. And if the seat
belt remains unfastened, the warning lamp and tone will issue further warnings each time the vehicle starts moving from a stop.
When the seat belt is fastened, the warnings
will stop.Adjustable seat belt anchor
(front seats)
E00405000286
The seat belt anchor height can be adjusted.
Seat belts
4-23OVWX17E1Seat and seat belts4

CAUTIONsuddenly; consequently, avoid driving athigh speeds or applying the brakes suddenly.
Furthermore, the vehicle should be brought
to a stop in a safe location and to have it checked.
• The brake warning lamp does not illumi-
nate when the parking brake is applied ordoes not turn off when the parking brake
is released.
• The ABS warning lamp and brake warn-
ing lamp illuminate at the same time.
For details, refer to “ABS warning lamp” on page 6-38.
• The brake warning lamp remains illumi-
nated during driving.
• The brake warning buzzer does not turn
off.
l The vehicle should be brought to a halt in
the following manner when brake perform-
ance has deteriorated.
• Depress the brake pedal harder than usual.
Even if the brake pedal moves down to
the very end of its possible stroke, keep it pressed down hard.
• Should the brakes fail, use engine braking
to reduce your speed and pull the parking
brake lever.
Depress the brake pedal to operate the
stop lamp to alert the vehicles behind you.NOTEl In certain cases immediately after the engine
has been started or when the brake pedal is
depressed repeatedly, a noise generated by operation of brake devices may be heard coming from the engine compartment. At
this time, you may feel a shock from the brake pedal if you depress it. This type of
noise or shock is normal and there is no need for concern. In fact, they indicate that the
corresponding devices are operating normal- ly.
l The brake system uses brake fluid pressur-
ized by the pump.
Please refer to “Braking” on page 6-35.Check engine warning lamp
E00502603052
This lamp is a part of an on-
board diagnostic system
which monitors the emis-
sions, engine control system or automatic transmission
control systems.
If a problem is detected in one of these sys-
tems, this lamp illuminates.
Although your vehicle will usually be driva-
ble and not need towing, we recommend you to have the system checked as soon as possi-
ble.

[Vehicles to comply with the Euro 4 regula-
tion]
This lamp will also illuminate for a few sec-
onds when the ignition switch is turned to the
“ON” position. If it does not go off after a few seconds, we recommend you to have the vehicle checked.

[Vehicles to comply with the Euro 5 and Eu-
ro 6]
This lamp will also illuminate when the igni-
tion switch is turned “ON”, and goes off after the engine has started. If it does not go off af- ter the engine has started, we recommend youto have the system checked.CAUTIONl Prolonged driving with this lamp on may
cause further damage to the emission control system. It could also affect fuel economy
and drivability.
l If the lamp does not illuminate when the ig-
nition switch is turned to the “ON” position,
we recommend you to have the system
checked.
l If the lamp illuminates while the engine is
running, avoid driving at high speeds and we recommend you to have the system checked.
Accelerator pedal and brake pedal response may be negatively influenced under these
conditions.
Warning lamps
5-11OVWX17E1Instruments and controls5

NOTE•It becomes dark and bright suddenly and
continuously around your vehicle.
• Your vehicle is driven on uneven surfa-
ces.
• Your vehicle is driven on a winding road.
• A reflective object such as a noticeboard
or a mirror reflects a light ahead of yourvehicle
• The rear end of a vehicle in front (such as
a container truck) reflect a strong light.
• Your vehicle’s headlamp is broken or
dirty.
• Your vehicle is inclined due to a flat tyre
or towing.
• The automatic high-beam system warning
lamp comes on.
l Observe the precautions below to maintain
good usage conditions:
• Do not touch the camera lens.
• Do not subject the inside rear view mirror
and the camera to strong impact. Do not spill any liquid over them.
• Do not attempt to disassemble the camera.
• Do not affix a sticker or label on the
windscreen near the camera.
• Do not place any objects on the instru-
ment panel.
• Do no hang any accessories around the in-
side rear view mirror or the camera.
• Avoid overload.
• Do not modify your vehicle.
• When the windscreen is replaced, use the
MITSUBISHI MOTORS genuine parts.Automatic high-beam system
warning lamp
E00538300046
The automatic high-beam system warning
lamp (yellow) will illuminate when the auto-
matic high-beam system detects any fault when the ignition switch is in the “ON” posi-
tion.
CAUTIONl If the warning lamp comes on, we recom-
mend you to have the system checked.NOTEl If the warning lamp comes on, press the
OFF side (2) on the automatic high-beam
system switch to deactivate the system. It is the responsibility of the driver to switch theheadlamp beams (high/low) manually to suit
each driving condition.
Refer to “Dipper (High/Low beam change)”
on page 5-36.Headlamp flasher
E00506300128
The high-beams flash when the lever is
pulled slightly (2), and will go off when it is
released.
When the high-beam is on, the high-beam in- dication lamp in the instrument cluster will il-
luminate.
NOTEl The high-beams can also flash when the
lamp switch is OFF.
l If you turn the lamps off with the headlamps
set to high-beam, the headlamps are auto- matically returned to their low-beam setting
when the lamp switch is next turned to the
“
” position.
Combination headlamps and dipper switch
5-39OVWX17E1Instruments and controls5

To adjust the sensitivity of the rain sensor
With the lever in the “AUTO” (rain sensor)
position, it is possible to adjust the sensitivity of the rain sensor by turning the knob (A).
“+”-Higher sensitivity to rain“-”-Lower sensitivity to rainNOTEl It is possible to activate the following func-
tions. For further information, we recom- mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
• Automatic operation (rain droplet sensi-
tive) can be changed to intermittent opera-
tion (vehicle-speed sensitive).
• Automatic operation (rain droplet sensi-
tive) can be changed to intermittent opera-
tion (except vehicle-speed sensitive).Misting function
Move the lever in the direction of the arrow
and release, to operate the wipers once.
Use this function when you are driving in
mist or drizzle.
The wipers will operate once if the lever is raised to the “MIST” position and released
when the ignition switch is in the “ON” or “ACC” position. The wipers will continue to
operate while the lever is held in the “MIST” position.
With the ignition switch in the “ON” posi-
tion, if the lever is moved to the AUTO posi- tion and pulled towards you a little, the wip-ers operate once.
The wipers will operate once if the lever is moved to the “AUTO” position and the knob
(A) is turned in the “+” direction when the ig-
nition switch is in the “ON” position.
Wiper and washer switch
5-47OVWX17E1Instruments and controls5

Windscreen washer
E00507200528
The washer fluid will be sprayed onto the
windscreen by pulling the lever towards you.
The wipers operate automatically several times while the washer fluid is being sprayed.
On a vehicle equipped with the headlamp
washer, the headlamp washer operates to- gether with the windscreen washer the first time the windscreen washer is used if the
headlamps are on.
CAUTIONl If the washer is used in cold weather, the
washer fluid sprayed against the glass may
freeze resulting in poor visibility. Heat the
glass with the defroster or demister before using the washer.Rear window wiper and wash-
er
E00507300994
The rear window wiper and washer switch
can be operated with the ignition switch in
the “ON” or “ACC” position.
INT-The wiper operates continuously for several seconds then operates inter- mittently at intervals of about every
8 seconds.OFF-Off-The washer fluid will be sprayed on-
to the rear window when the knob is turned fully in either direction.
The wipers operate automatically
several times while the washer fluid is being sprayed.NOTEl To ensure a clear rearward view, the wiper
performs several continuous operations
when the reverse gear is engaged while the
switch is in the “INT” position.
Following this continuous operation, the wiper will automatically switch to intermit-
tent operation.
l It is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
• Adjustment of the interval for intermittent
operation
• The wipers can be changed to continuous
operation by turning the knob at the end of the lever twice to the --- (intermittent operation) position. (Continuous opera- tion mode)
• Changing intermittent wiper operation to
continuous wiper operationHeadlamp washer switch*
E00510100231
The headlamp washer can be operated when
the ignition switch is in the “ON” or “ACC” position and the headlamps are on.
Wiper and washer switch
5-48OVWX17E1Instruments and controls5