2017 MINI Convertible Owner's Manual

by using the maximum cooling or heating
power, and then keeps it constant.
Settings Turn the ring to set the desired
temperature.
The automatic climate control reaches this temperature as quickly as possible, if needed,
by increasing the cooling or heating output, and then keeps it constant.
Do not rapidly switch between different tem~
perature settings. The automatic climate con~
trol will not have sufficient time to adjust the
set temperature.
Air
conditioning
Concept
The air in the vehicle's interior will be cooled
and dehumidified and, depending on the tem~
perature setting, warmed again.
The vehicle's interior can only be cooled with
the engine running.
Switching
on/off Press button.
Air conditioning is switched on or off.
Depending on the weather, the windshield may
fog up briefly when the engine is started.
The cooling function is switched on automati~ cally with the AUTO program.
When using the automatic climate control, con~
densation water, refer to page 176, develops
and drains underneath the vehicle. This is nor~
mal.Maximum
cooling
Concept
The system is set to the lowest temperature,
maximum air flow and recirculated-air mode.
General
information
The function is available with external tempera~
tures beyond approx. 32 

Intensity
With the AUTO program activated, the auto~
matic intensity control can be changed.
Turn the ring to set the desired
intensity from soft to intensive.
The set intensity is displayed via the position of the illuminated LED segment.
Convertible
program
When the convertible top is open, the converti~
ble program is activated as well. In the conver~
tible program, the automatic climate control is
optimized for driving with the convertible top
open. In addition, the air flow is increased as
the vehicle speed increases.
The efficiency of the convertible program can
be greatly enhanced by installing the wind de~
flector.
Recirculated-air
mode
Concept
You may react to unpleasant odors or pollu~
tants in the immediate environment by tempo~
rarily suspending the supply of outside air. The
system then recirculates the air flow within the
vehicle.
Operation Press button repeatedly to select an
operating mode:'

'

Parked-car
ventilation
The
concept
The parked-car ventilation ventilates the vehi~ cle interior and lowers its temperature, ifneeded.
The system can be switched on and off at any external temperature, either directly or by us~ ing two preset activation times. It remainsswitched on for 30 minutes.
Open the vents to allow air to flow out.
Switching
on/off
directly Via the onboard monitor:1. "Settings"2."Climate"3."Activate comf. ventilation"
The symbol on the automatic climate con~
trol flashes if the system is switched on.
Preselecting
the
activation
time
Via the onboard monitor:
1. "Settings"2."Climate"3."Timer 1:" or "Timer 2:"4.Set the desired time.
Activating
the
activation
time Via the onboard monitor:
1. "Settings"2."Climate"3."Activate timer 1" or "Activate timer 2"
The symbol on the automatic climate con~
trol lights up when the switch-on time is acti~
vated.
The symbol on the automatic climate con~
trol flashes when the system has been switched
on.
The system will only be switched on within the next 24 hours. After that, it needs to be reacti~
vated.Seite 156CONTROLSClimate
control156
Online Edition for Part no. 01 40 2 915 102 - X/16

Interior
equipmentVehicle
features
and
op

proximately 20 seconds until the LED on
the interior mirror flashes. This erases all
programming of the buttons on the interior mirror.3.Hold the hand-held transmitter for the sys~
tem to be controlled approx. 1 to 3 in~
ches/2.5 to 8 cm away from the buttons of
the interior mirror. The required distance depends on the hand-held transmitter.4.Simultaneously press and hold the button
of the desired function on the hand-held
transmitter and the button to be program~
med on the interior mirror. The LED on the
interior mirror will begin flashing slowly.5.Release both buttons as soon as the LED
flashes more rapidly. The LED flashing
faster indicates that the button on the inte~
rior mirror has been programmed.
If the LED does not flash faster after at least 60 seconds, change the distance betweenthe interior mirror and the hand-held trans~
mitter and repeat the step. Several more
attempts at different distances may be nec~
essary. Wait at least 15 seconds between
attempts.
Canada: if programming with the hand- held transmitter was interrupted, hold
down the interior mirror button and repeat~
edly press and release the hand-held trans~
mitter button for 2 seconds.6.To program other functions on other but~
tons, repeat steps 3 to 5.
The systems can be controlled using the interior mirror buttons.
Special
feature
of
the
rolling
code
wireless
system
If you are unable to operate the system after repeated programming, please check if the sys~
tem to be controlled features a rolling code ra~
dio system.
Read the system's owner's manual, or press the
programmed button on the interior mirror lon~
ger. If the LED on the interior mirror starts
flashing rapidly and then stays lit constantly for
2 seconds, the system features a rolling code
radio system. Flashing and continuous illumina~
tion of the LED will repeat for approximately
20 seconds.
For systems with a rolling code radio system,
the Universal Integrated Remote Control and
the system also have to be synchronized.
Please read the owner's manual to find out
how to synchronize the system.
Synchronizing is easier with the aid of a second
person.
Synchronizing the universal remote control
with the system:1.Park the vehicle within range of the re~
mote-controlled system.2.Program the relevant button on the interior mirror as described.3.Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.4.Hold down the programmed button on the interior mirror for approximately 3 secondsand then release it. If necessary, repeat this
step up to three times in order to finish syn~
chronization. Once synchronization is com~
plete, the programmed function will be car~
ried out.
Reprogramming
individual
buttons
1.Switch on the ignition.2.Press and hold the interior mirror button to
be programmed.3.As soon as the interior mirror LED starts
flashing slowly, hold the hand-held trans~
mitter for the system to be controlled ap~
prox. 1 to 3 inches/2.5 to 8 cm away from
the buttons of the interior mirror. The re~ quired distance depends on the hand-held
transmitter.Seite 158CONTROLSInterior
equipment158
Online Edition for Part no. 01 40 2 915 102 - X/16

4.Likewise, press and hold the button of the
desired function on the hand-held trans~ mitter.5.Release both buttons as soon as the interior
mirror LED flashes more rapidly. The LED
flashing faster indicates that the button on the interior mirror has been programmed.
The system can then be controlled by the
button on the interior mirror.
If the LED does not flash faster after at most 60 seconds, change the distance and re~
peat the programming starting with step 4.
Several more attempts at different distan~
ces may be necessary. Wait at least 15 sec~
onds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior mirror button and repeat~
edly press and release the hand-held trans~
mitter button for 2 seconds.
Operation
WARNING
Body parts can be jammed when operat~
ing remote-controlled systems, e.g., the garage
door, using the integrated universal remote
control. There is a risk of injury or risk of prop~
erty damage. Make sure that the area of move~ ment of the respective system is clear during
programming and operation. Also follow the
safety instructions of the hand-held transmit~
ter. '

Setting
the
compass
zonesSets the particular compass zones on the vehi~
cle so that the compass operates correctly; re~
fer to World map with compass zones.
World
map
with
magnetic
zones
Procedure1.Press and hold the control button for ap~
prox. 3 to 4 seconds. The number of the set
compass zone appears in the mirror.2.To change the zone setting, press the con~
trol button quickly and repeatedly until the
number of the compass zone that corre~
sponds with your location appears in the
mirror.
The set zone is stored automatically. The com~
pass is ready for use again after approximately 10 seconds.
Calibrating
the
digital
compass The digital compass must be calibrated in theevent of the following:
'