2017 MERCEDES-BENZ S-Class MAYBACH fold seats

Door controlpanel
FunctionPage
:s Seat ventilation113
;c Seat heatin g112
=w Adjust sth efront-
passenger seat from th e
driver’s seat
10 3
?r 45=
Stores settings for the seat,
exterior mirrors and steering
column
120
AAdjusts the seats electrically101
B7Zª\
Adjusts and folds the exterior
mirrors in/out electrically
117
CW Opens/closes the right
side window90
FunctionPage
DW Opens/closes the rear
right side window90
Ep Opens/closes the
trunk lid89
Fn Override feature for the
controls in the rear compart-
ment
65
GOpens the door83
H%&Unlocks/locks
the vehicle83
IW Opens/closes the rear
left side window90
JW Opens/closes the left
side window90
40Door control panel
At a glance

before installing the LATCH-type (ISOFIX)
child restraint system.
XVehicles without rear reclining seat:fold
upholstered lining :upwards.
XVehicles with a rear reclining seat: remove
upholstered lining :.
XVehicles without a rear reclining seat: turn
the support on the rear side of upholstered
lining :by 90°.
Upholstered lining :remains folded
upwards.
XInstall the LATCH-type (ISOFIX) child restraint
system on both LATCH-type (ISOFIX) securing
rings ;.
XVehicles with a rear reclining seat: move
the rear reclining seat backrest to an upright
position. The rear reclining seat backrest
must rest against the child restraint system.
GWARNING
Vehicles with electrically adjustable rear
bench seats:
If you adjust the seat after installing a child
restraint system:
Rthe seat belt could slacken or become too
tight
Rthe child restraint system could become
loose, incorrectly positioned or damaged
As a result, the child restraint system may not
be able to provide the intended level of pro-
tection. This poses an increased risk of injury
or even fatal injury.
Never adjust the seat after installing the child
restraint system.
Vehicles without rear reclining seat: after
you have removed the LATCH-type (ISOFIX)
child restraint system, you must turn the sup-
port on the rear side of upholstered lining :by
90° again. Then fold upholstery lining :down.
ISOFIX is a standardized securing system for
specially designed child restraint systems on
the rear seats. LATCH-type (ISOFIX) securing
rings ;for two LATCH-type (ISOFIX) child
restraint systems are installed on the left and
right rear seats.
Vehicles with rear seat armrest: adjust the
rear seat armrest so that LATCH-type (ISOFIX)
securing rings ;for the LATCH-type (ISOFIX)
child restraint system are accessible. Non-LATCH-type (ISOFIX) child seats may also
be used and can be installed using the vehicle's
seat belt system. Install the child seat according to the manufacturer's instructions.
Top Tether
Introduction
Top Tether provides an additional connection
between the child restraint system secured with
a LATCH-type (ISOFIX) system and the vehicle.
This helps reduce the risk of injury even further.
If the child restraint system is equipped with a
Top Tether belt, this should always be used.
Important safety notes
GWARNING
If the rear seat backrests are not locked, they
could fold forwards in the event of an acci-
dent, heavy braking or sudden changes of
direction. As a result, child restraint systems
cannot perform their intended protective
function. Rear seat backrests that are not
locked can also cause additional injuries, e.g.
in the event of an accident. This poses an
increased risk of injury or even fatal injury.
Always lock rear seat backrests after instal-
ling a Top Tether belt. Observe the lock veri-
fication indicator. Adjust the rear seat backr-
ests so that they are in an upright position.
GWARNING
Vehicles with electrically adjustable rear
bench seats:
If you adjust the seat after installing a child
restraint system:
Rthe seat belt could slacken or become too
tight
Rthe child restraint system could become
loose, incorrectly positioned or damaged
As a result, the child restraint system may not
be able to provide the intended level of pro-
tection. This poses an increased risk of injury
or even fatal injury.
62Children in the vehicle
Safety

Never adjust the seat after installing the child
restraint system.
If the rear seat backrest is not engaged and
locked, this will be shown in the multifunction
display in the instrument cluster. A warning tone
also sounds.
Top Tether anchorages
The Top Tether anchorage points are installed in
the rear compartment behind the head
restraints on the parcel shelf.
XMove the head restraint up (Ypage 111).
XFold up cover :of the Top Tether anchorage.
XInstall the LATCH-type (ISOFIX) child restraint
system with Top Tether. Always comply with
the child restraint system manufacturer's
installation instructions when doing so.
XRoute Top Tether belt ?under the head
restraint between the two head restraint bars.
XHook Top Tether hook =of Top Tether
belt ?into Top Tether anchorage ;.
Make sure that Top Tether belt ?is not twis-
ted.
XTension Top Tether belt ?. Always comply
with the child restraint system manufactur-
er's installation instructions when doing so.
XFold down cover :of the Top Tether anchor-
age.
XIf necessary, move the head restraint back
down again slightly (Ypage 111). Make sure
that you do not interfere with the correct rout-
ing of Top Tether belt ?.
Child restraint system on the front-
passenger seat
General notes
Accident statistics show that children secured
in the rear seats are safer than children secured
in the front-passenger seat. For this reason,
Mercedes-Benz strongly advises that you install
the child restraint system on a rear seat.
If it is absolutely necessary to install a child
restraint system on the front-passenger seat,
always observe the instructions and safety
notes on the "Occupant Classification System
(OCS)" (
Ypage 51).
You can thus avoid the risks that could arise as a result of:
Ran incorrectly categorized person in the front-
passenger seat
Rthe unintentional deactivation of the front-
passenger front air bag
Rthe unsuitable positioning of the child
restraint system, e.g. too close to the dash-
board
Rearward-facing child restraint system
If it is absolutely necessary to install a rearward-
facing child restraint system on the front-
passenger seat, always make sure that the
front-passenger front air bag is deactivated.
Only if the PASSENGER AIR BAG OFF indicator
lamp is permanently lit (
Ypage 43) is the front-
passenger front air bag deactivated.
Always observe the child restraint system man-
ufacturer's installation and operating instruc-
tions.
Forward-facing child restraint system
If it is absolutely necessary to install a forward-
facing child restraint system on the front-
passenger seat, always move the front-
passenger seat as far back as possible. Fully
retract the seat cushion length. The entire base
Children in the vehicle63
Safety
Z

ACombined seat cushion angleand length
BLegrest ang le
CLegrest length
The rear rec lining seat isonly availab le inlong
wheelbase veh iclesequipp edwith "executive
seats". On veh icleswit hout a rear rec lining seat,
the button for setting the ang leand length of the
legrest has no function.
Vehicle swit h a long wheelbase: dependin g on
the veh icleequipment, the rear rec lining seat is
either only on the front-passenger sideor also
on the driver's side.
Mercedes-Maybach veh icles: the rear rec lining
seats are on the driver's and the front-
passenger side.
Vehicle swit h a long wheelbase and equipped
wit h a "Rear compartment chauffeur/memory
package" also have a footrest. This islocated on
the lower part of the front-passenger seat back-
rest (
Ypage 104).
The legrest folds down ifoverloaded. Ifth is is the
case fold up the legrest and engage it.
Setting the reclined position
This function isonly availab lefor long wheelbase
veh icles.
You can use the overr idebutton to disable this
function (
Ypage 65).
The power supplyor the ignition must be
swit ched on so that the rear seat can bemoved
to the rec lined position (
Ypage 146).
XPress and hold button :untilthe seat has
reached the rec lined position.
The rear seat moves into the rec lined posi-
tion, the front-passenger seat moves into the
chauffeur position (
Ypage 106) and the foot-
rest moves out from under the front-
passenger seat. You can exit the reclined position and adjust
the seat position by:
Rpressing button
:
Rcalling up a stored position using memory
button1or 2(Ypage 121)
Rmanually adjusting the seat to the desired
position (Ypage 101)
iThe steps for setting the reclined position
are not always carried out simultaneously.
The legrest folds down if overloaded. Ifthis is the
case fold up the legrest and engage it.
Adjusting the front-passenger seat
from the driver’s seat
Important safety notes
GWARNING
When you adjust a seat, you or other vehicle
occupants could become trapped, e.g. on the seat guide rail. There isa risk of injury.
Make sure when adjusting a seat that no one
has any body parts in the sweep of the seat.
Observe the safety notes on "Air bags"
(
Ypage 48) and "Children inthe Vehicle"
(Ypage 59).
GWARNING
The front-air bags for could also injure the
vehicle occupants in the front If the front
seats are positioned too close to the dash-
board or steering wheel. This poses an
increased risk of injury or even fatal injury.
Always adjust the front seats so that they are
as far from the front air bags as possible. Also
observe the notes on the correct adjustment
of the seats.
GWARNING
Childr en could become trapped if they adjust
the seats, particularly when unattende d.
There isa risk of injury.
When leaving the vehicle, always take the
Sm artKey with you and lock the vehicle. Never
leave children unsupervised in the vehicle.
Seats103
Seats, steering wheel and mirrors
Z

BSeat height
CFootrest
The power supply or the ignition must be
switched on so that the front-passenger seat
can be selected (
Ypage 146).
XTo select the front-passenger seat: press
button :repeatedly until the indicator lamp
in the button lights up.
The front-passenger seat is selected if the
indicator lamp in the button lights up.
XAdjust the front-passenger seat with but-
tons ;toC.
The footrest can only be adjusted if:
Rthe front-passenger seat is moved fully
forward
Rthe front-passenger seat is in the position for
chauffeur mode (Ypage 106).
iThe front-passenger seat in the Mercedes-
Maybach must not be positioned fully for-
wards when adjusting the footrest. The front-
passenger seat must be moved forwards from
the rear to the middle adjustment range.
Chauffeur mode
Important safety notes
GWARNING
If the head restraints are not installed or not
adjusted correctly, they cannot provide pro-
tection as intended. There is an increased risk
of injury in the head and neck area, e.g. in the event of an accident or when braking.
Always drive with the head restraints instal-
led. Before driving off, make sure for every
vehicle occupant that the center of the head
restraint supports the back of the head at
about eye level.
Using the fore-and-aft adjustment, adjust the
head restraint so that it is as close as possible to
your head.
GWARNING
If the front-passenger seat is in chauffeur
mode and the front-passenger head restraint
is folded down, the view of the passenger-side
exterior mirror can be impaired. There is a risk of an accident.
To have a free view of the exterior mirror,
remove the front-passenger head restraint.
!Make sure that there are no objects in the
footwell under or behind the seats when mov-
ing the seats back. There is a risk that the
seats and/or the objects could be damaged.
General notes
In chauffeur mode:
Rthe front-passenger seat is moved forwards
Rthe backrest is tilted forwards
Rthe head restraint is folded forwards
The front-passenger seat automatically moves
from the chauffeur position back into the normal
position if:
Rthe front-passenger seat is adjusted using the
seat adjustment switch on the front-
passenger door
Rthe front-passenger seat belt is fastened
Ran occupant is detected on the front-
passenger seat
Rthe front-passenger seat head restraint is
inserted and the ignition is switched on
Rthe front-passenger seat backrest is moved
backwards or the seat is moved in a longitu-
dinal direction out of the chauffeur area
(
Ypage 108)
Positioning the front-passenger seat for
chauffeur mode
General notes
Pay attention to the important safety notes
(Ypage 106). Adjust the seat for chauffeur
mode before the journey. Do not remove the
front-passenger seat head restraint during the
journey.
106Seats
Seats, steering wheel and mirrors

Adjusting from the rear compar tment
You can use th eoverride butto nto disable this
function (Ypage 65).
In order for th efront-passenger seat to be posi -
tione din chauffeur mode:
Rth epower suppl yor th eignition must be
switched on (Ypage 146)
Rthefront-passenger seat may no tbe occupied
Rth efront-passenger seat belt must no tbe
inserted int oth ebuckle
XTo select th e front-passenger seat :press
butto n: repeatedly until th eindicator lamp
in th ebutto nlights up.
The front-passenger seat is selected if th e
indicator lamp in th ebutto nlights up.
XPress butto n; forwards and hold it in this
position.
The seat moves forward.
The seat stops at th ethreshold of th earea for
chauffeur mode.
XReleas ebutto n;.
XPress and hold butto n; again until th efront-
passenger seat is in positio nfor chauffeur
mode.
The head restraint on th efront-passenger
seat folds forward. The seat moves forward.
The To vie wthe ext .mirror ,adjust
front-passenger sea tor remove thehea drestraint .message appear sin th e
multifunction display (Ypage 256).
iIf thefront-passenger seat is already at th e
threshold to th earea for th echauffeur mode,
th epositio nfor th echauffeur mod eis set
immediately.
iThe positio nfor chauffeur mod ecan be
saved or set usin gth ememory function of th e
rear seat (
Ypage 121). Fo rthis th eindicator
lamp on butto n: must be lit .
Adjusting fr om the driver's seat
In order for th efront-passenger seat to be posi -
tione din chauffeur mode:
Rth epower suppl yor th eignition must be
switched on (Ypage 146)
Rthefront-passenger seat may no tbe occupied
Rth efront-passenger seat belt must no tbe
inserted int oth ebuckle
XTo select th e front-passenger seat :press
butto n: repeatedly until th eindicator lamp
in th ebutto nlights up.
The front-passenger seat is selected if th e
indicator lamp in th ebutto nlights up.
XPress butto n; forwards and hold it in this
position.
The seat moves forward.
The seat stops at th ethreshold of th earea for
chauffeur mode.
XReleas ebutto n;.
XPress and hold butto n; again until th efront-
passenger seat is in positio nfor chauffeur
mode.
The head restraint on th efront-passenger
seat folds forward. The seat moves forward.
The To vie wthe ext .mirror ,adjust
front-passenger sea tor remove thehea drestraint .message appear sin th e
multifunction display (Ypage 256).
iIf thefront-passenger seat is already at th e
threshold to th earea for th echauffeur mode,
th epositio nfor th echauffeur mod eis set
immediately.
iThe positio nfor chauffeur mod ecanno tbe
store dor set wit hth edriver' sseat memory
function .
Seats107
Seats, steering wheel and mirrors
Z

Installing/removing the head restraint
Removing
XMoveth eseat int oth eposition for chauffeur
mode, until th ehead restrain tfolds forward
completely (
Ypage 106).
XFold head restrain tbar cover s; backwards.
XPull adjuster lever ?backwards and hold it in
this position .Hold head restrain t: while
doin gso.
XRemove head restrain t:.
XReleas eadjuster lever ?.
Red pin =protrudes from th eadjuster lever.
XPress down red pin =.
XFold covers; forwards and close them.
Installing
XFold cover s; backwards.
XPull handle ?backwards.
Red pin =protrudes from th eadjuster lever.
XInser thead restrain t: intoth ebrackets .
The head restrain tmust engage on bot h
sides.
XPress down red pin =.
If th epin can be presse ddown and is then no
longer visible, th ehead restrain thas engage d
correctly.
XFold cover s; forwards and close them.
The head restrain tfolds int oposition auto -
matically.
Moving the front-passenger seat into
the normal position
Adjusting fr om the rear compar tment
You can use th eoverride butto nto disable this
function (Ypage 65).
The head restrain tmust be installed, in order for
th efront-passenger seat to be moved int oth e
normal position (
Ypage 108).
The power suppl yor th eignition must be
switched on so that th efront-passenger seat
can be selected (
Ypage 146).
XTo select thefront-passenger seat: press
butto n: repeatedly until th eindicator lamp
in th ebutto nlights up.
The front-passenger seat is selected if th e
indicator lamp in th ebutto nlights up.
XPress butto n= backwards and hold it in this
position .
The front-passenger seat moves int oth enor-
mal adjustmen trange at th ethreshold of th e
area for chauffeur mode. The head restrain t
folds int oposition .
If you continue to hold down butto n=, the
seat continue sto mov ebackwards.
or
XBriefly press butto n; backwards.
The front-passenger seat moves int oth enor-
mal adjustmen trange at th ethreshold to th e
area for chauffeur mode. The head restrain t
folds int oposition .
108Seats
Seats, steering wheel and mirrors

iFurther settings are available via the mem-
ory function buttons, if:
Ra position in the normal setting has already been saved
Rthe front-passenger seat has been selected
with button :
Adjusting from the driver's seat
The head restraint must be installed, in order for
the front-passenger seat to be moved into the
normal position (
Ypage 108).
The power supply or the ignition must be
switched on so that the front-passenger seat
can be selected (
Ypage 146).
XTo select the front-passenger seat: press
button :repeatedly until the indicator lamp
in the button lights up.
The front-passenger seat is selected if the
indicator lamp in the button lights up.
XPress button =backwards and hold it in this
position.
The front-passenger seat moves into the nor-
mal adjustment range at the threshold of the
area for chauffeur mode. The head restraint
folds into position.
If you continue to hold down button =, the
seat continues to move backwards.
or
XBriefly press button ;backwards.
The front-passenger seat moves into the nor-
mal adjustment range at the threshold to the
area for chauffeur mode. The head restraint
folds into position.
iFurther settings are available via the mem-
ory function buttons if the front-passenger
seat has been selected via button :.
Adjusting from the front-passenger seat
XPress any seat adjustment button.
The front-passenger seat moves into the nor-
mal adjustment range at the threshold of the
area for chauffeur mode. The head restraint
folds into position.
Fully reclined position of the front-
passenger seat
Setting
This function is only available on vehicles with
electrically adjustable rear seats.
You can move the front-passenger seat into a
fully reclined position. The rear seat and front-
passenger seat then provide a continuous sur-
face. The rear-seat passenger can use the front-
passenger seat backrest as a legrest.
To do so:
Rmove the seat cushion of the rear seat as far
back as possible in a longitudinal direction
(
Ypage 102)
Rmove the front-passenger seat into position
for chauffeur mode (Ypage 106)
Rremove the front-passenger head restraint
(Ypage 108)
Rmove the front-passenger seat so that the
backrest is in a fully reclined position
(
Ypage 101)
Exiting
To exit the fully reclined position:
Rfold the backrest upright to a suitable position
Rinstall the front-passenger head restraint
(Ypage 108)
Adjusting the head restraints
Important safety notes
GWARNING
You could lose control of your vehicle if you do the following while driving:
Radjust the driver's seat, head restraint,
steering wheel or mirrors
Rfasten the seat belt
There is a risk of an accident.
Seats109
Seats, steering wheel and mirrors
Z