2017 MAZDA MODEL CX-5 steering wheel

6–45
Maintenance and Care
Owner Maintenance
*Some models.
CAUTION
When removing the lens or lamp unit
using a fl athead screwdriver, make
sure that the fl athead screwdriver does
not contact the interior terminal. If
the fl athead screwdriver contacts the
terminal, a short circuit may occur.

NOTE
  To replace the bulb, contact an
Authorized Mazda Dealer.
  Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.

Replacing Exterior Light Bulbs
Headlights/Daytime running lights,
Daytime running lights/Parking lights
(Type A), Front side-marker lights
(Type A), Fog lights
* , Brake lights (Type
A), Taillights (Type A), Reverse lights,
High-mount brake light, Side turn
signal lights, Rear side-marker lights
(Type A)
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary.
Front turn signal lights/Parking lights
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood.
Refer to Hood on page 6-20 .
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.


5. Install the new bulb in the reverse order of the removal procedure.

Front side-marker lights (Type B)
1. Make sure the ignition is switched off, and the headlight switch is off.
2. If you are changing the right bulb, start the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right.
3. Pull the center of each plastic retainer using a fl athead screwdriver and
remove the retainers, and then partially
peel back the over fender.

Removal
Installation

CX-5_8FN1-EA-16L_Edition1.indb 452016/12/12 10:07:13

6–53
Maintenance and Care
Owner Maintenance
*Some models.
DESCRIPTION FUSE
RATING PROTECTED COMPONENT
14 FAN GE 30 A Cooling fan
15 ENG.MAIN 40 A Engine control system
16 ABS/DSC M 50 A ABS, Dynamic stability control system
17 FAN DE 40 A —
18 WIPER 20 A Front window wiper and washer
19 HEATER 40 A Air conditioner
20 ADD FAN GE 30 A Cooling fan
21 ENGINE.IG1 7.5 A Engine control system
22 C/U IG1 15 A For protection of various circuits
23 AUDIO2 7.5 A Audio system
24 METER2 7.5 A —
25 ENGINE3 15 A Engine control system
26 ENGINE2 15 A Engine control system
27 ENGINE1 15 A Engine control system
28 AT 15 A Transaxle control system
* , Ignition switch
29 H/CLEAN 20 A —
30 A/C 7.5 A Air conditioner
31 AT PUMP 15 A Transaxle control system
*
32 HORN 15 A Horn
33 R.WIPER 15 A Rear window wiper
34 H/L HI 20 A Headlight high beam
35 ST.HEATER 15 A Heated steering wheel
*
36 FOG 15 A Fog lights *
37
7.5 A Engine control system
38 H/L LOW L 15 A Headlight low beam (LH)
39 ENGINE4 15 A —
40 — — —
41 METER1 10 A Instrument cluster
42 SRS1 7.5 A Air bag
43 BOSE 25 A Bose
® Sound System-equipped model *
44 AUDIO1 15 A Audio system
45 ABS/DSC S 30 A ABS, Dynamic stability control system
46 FUEL PUMP 15 A Fuel system
47 FUEL WARM 25 A —
48 TAIL 15 A Taillights, License plate lights
49 SCR2
FUEL PUMP2 25 A
—
50 HAZARD 25 A Hazard warning
fl ashers, Turn signal lights/Front side-marker
lights, Parking lights
CX-5_8FN1-EA-16L_Edition1.indb 532016/12/12 10:07:16

7–25
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning


(Red)
High Engine Coolant
Temperature Warning Indication/Warning Light
The light fl ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can fi nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a saf\
e place
immediately and stop the engine.
Refer to Overheating 7-18 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.


Power Steering
Malfunction Indication
* The message is displayed if the electric power steering has a malfunctio\
n.
If the message is displayed, stop the vehicle in a safe place and do not\
operate the
steering wheel. There is no problem if the message in the display turns off after a while.
Contact an Authorized Mazda Dealer if the message is displayed continuously.
NOTE

If the message is displayed, the power steering will not operate normall\
y. In this
case, the steering wheel can still be operated, however, the operation may feel heavy
compared to normal, or the steering wheel could vibrate when turning.
 Repeatedly jerking the steering wheel left and right while the vehicle i\
s stopped or
moving extremely slowly will cause the power steering system to go into protective
mode which will make the steering feel heavy, but this does not indicate a problem. If
this occurs, park the vehicle safely and wait several minutes for the sy\
stem to return
to normal.


Power Steering
Malfunction Indicator Light
* The light illuminates/
fl ashes if the electric power steering has a malfunction.
If the light illuminates/ fl ashes, stop the vehicle in a safe place and do not operate the
steering wheel. There is no problem if the light turns off after a while. Contact an
Authorized Mazda Dealer if the light illuminates/ fl ashes continuously.
NOTE

If the indicator light illuminates/ fl ashes, the power steering will not operate normally.
If this happens, the steering wheel can still be operated, however, the operation may
feel heavy compared to normal, or the steering wheel could vibrate when turning.
 Repeatedly jerking the steering wheel left and right while the vehicle i\
s stopped or
moving extremely slowly will cause the power steering system to go into protective
mode which will make the steering feel heavy, but this does not indicate a problem. If
this occurs, park the vehicle safely and wait several minutes for the sy\
stem to return
to normal.

CX-5_8FN1-EA-16L_Edition1.indb 252016/12/12 10:07:24

7–35
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Message Indicated in Multi-information Display *
If there is a notifi cation from the vehicle, a message is displayed in the multi-information\

display. Check the information and take the necessary action.


(Display example)

If the warning light turns on/ fl ashes simultaneously or a symbol is indicated in the display,
check the information regarding the warning light or symbol. (page 4-32 )

Display Content Action to be taken

Indicated when the push button start is
pressed while the shift lever is not in the
P position.
Shift the shift lever to the P position.

Indicated when the push button start is
pressed without depressing the brake
pedal.
Depress the brake pedal and press the
push button start.

Indicated while the steering wheel is
locked.
Release the steering lock.

Indicates when the Electric Parking
Brake (EPB) switch is operated without
depressing the brake pedal.
Operate the Electric Parking Brake
(EPB) switch while depressing the brake
pedal.
CX-5_8FN1-EA-16L_Edition1.indb 352016/12/12 10:07:27

7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Key Removed from Vehicle Warning Beep
Vehicles with advanced keyless function
If the key is taken out of the vehicle while
the ignition is not switched OFF and
all the doors are closed, the beep which
sounds outside of the vehicle will be heard
6 times, the beep which sounds inside
the vehicle will be heard 6 times, and the
KEY warning light (red) in the instrument
cluster fl ashes continuously to notify
the driver that the ignition has not been
switched OFF.
Vehicles without advanced keyless
function
If the key is taken out of the vehicle while
the ignition is not switched OFF and all
the doors are closed, a beep will be heard
in the cabin 6 times and the KEY warning
light (red) in the instrument cluster turns
on continuously to notify the driver that
the ignition has not been switched OFF.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key is
carried together with a metal object or it
is placed in a poor signal reception area.

Request Switch Inoperable Warning Beep (With the advanced
keyless function)
If the request switch is pressed with the
door open or ajar, or the ignition is not
switched OFF with a key being carried, a
beep will be heard outside for about
2 seconds to notify the driver that the door
or liftgate cannot be locked.
Key Left-in-luggage Compartment Warning Beep (With the advanced
keyless function)
If the key is left in the luggage
compartment with all the doors locked and
the liftgate closed, a beep will be heard
outside for about 10 seconds to notify
the driver that the key is in the luggage
compartment. In this case, take out the
key by pressing the electric liftgate opener
and opening the liftgate. The key taken
out of the luggage compartment may
not operate because its functions have
been temporarily stopped. To restore the
key's functions, perform the applicable
procedure (page 3-9 ).
Key Left-in-vehicle Warning Beep (With the advanced keyless
function)
If all the doors and luggage compartment
are locked using another key while the key
is left in the cabin, the beep which sounds
outside of the vehicle will be heard for
about 10 seconds to notify the driver that
the key is in the cabin. In this case, take
out the key by opening the door. A key
taken out of the vehicle using this method
may not operate because its functions have
been temporarily stopped. To restore the
key's functions, perform the applicable
procedure (page 3-9 ).
Electronic Steering Lock Warning Beep *
The warning beep operates if the steering
wheel is not unlocked after the push button
start is pressed. (page 4-4 )
CX-5_8FN1-EA-16L_Edition1.indb 412016/12/12 10:07:29

7–42
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Power Liftgate Warning Beep *
If system operation precautions are
necessary, the driver is notifi ed by the
warning sound.

Cautions What to check
The beep sounds 3 times The conditions required
for the power liftgate
to operate have not
been met, such as an
object being stuck in the
liftgate.
The beep sound
continues The vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.

Electric Parking Brake (EPB)
Warning Beep
The warning buzzer is activated under the
following conditions:
   The vehicle is driven with the electric
parking brake (EPB) applied.
   The electric parking brake (EPB) switch
is pulled while the vehicle is driven.

AUTOHOLD Warning Beep
Warning light fl ashes/message is
displayed and beep sound is activated
simultaneously for about fi ve seconds
when using AUTOHOLD function or
when AUTOHOLD switch is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.

If the warning light fl ashes/message is
displayed and the beep sound is activated
simultaneously, have your vehicle
inspected at an Authorized Mazda Dealer.
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or fl ashes and
the buzzer operates at the same time.
Refer to Warning Indication/Warning
Lights on page 4-33 .
Tire Infl ation Pressure Warning
Beep *
The warning beep sound will be heard
for about 3 seconds if the tire pressures
decrease.
If the tire pressure decreases extremely,
a beep sound will be heard for
approximately 30 seconds.
Refer to Tire Pressure Monitoring System
on page 4-172 .
Blind Spot Monitoring (BSM) Warning Beep *
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the Blind Spot Monitoring (BSM) warning
light is illuminated.
NOTE
A personalized function is available to
change the Blind Spot Monitoring (BSM)
warning beep sound volume.
Refer to Personalization Features on page
9-11 .

Reversing
If a moving object such as a vehicle or
two-wheeled vehicle approaches on the
left or right from behind your vehicle, the
Blind Spot Monitoring (BSM) warning
sound is activated.
CX-5_8FN1-EA-16L_Edition1.indb 422016/12/12 10:07:29

9–12
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings
Change
Method


Lane-keep Assist
System (LAS) &
Lane Departure
Warning System
(LDWS) (page
4-135 ) The system can be changed so that the
steering wheel assist does not operate.
On On/Off A —


When the steering wheel
operation assistance is
turned on The cancel
sensitivity of
the steering
assistance for the
Lane-keep Assist
System (LAS) &
Lane Departure
Warning System
(LDWS) can be
changed.
High High/Low A —


The system can
be changed so
that the Lane
Departure
Warning does not
activate. On On/Off A —


When the steering wheel
operation assistance is
turned off The warning
timing in which
the Lane-keep
Assist System
(LAS) & Lane
Departure
Warning System
(LDWS) system
determines that
the vehicle may
be deviating
from its lane can
be changed.
At At/Before A —


The sensitivity
of the warning
for the Lane-
keep Assist
System (LAS) &
Lane Departure
Warning System
(LDWS) can be
changed. Often Often/Rare A —


The type of Lane-keep Assist System (LAS)
& Lane Departure Warning System (LDWS)
warning can be changed. Vibration
Vibration/Beep/
Rumble A —


The warning intensity/
volume of the Lane-keep
Assist System (LAS) &
Lane Departure Warning
System (LDWS) system
can be changed. Vibration
Low High/Low A —


Rumble Low High/Mid/Low A —


Beep Low High/Low A —


CX-5_8FN1-EA-16L_Edition1.indb 122016/12/12 10:07:39

10–4
Index
E
Electric Parking Brake (EPB) Warning
Beep .................................................... 7-42
Electric parking brake (EPB) .............. 4-71
Electronic steering lock warning beep ... 7-41
Emergency Starting
Push-starting .................................. 7-17
Starting a fl ooded engine ............... 7-17
Emergency Towing Tiedown hooks .............................. 7-21
Towing description ........................ 7-20
Emission Control System .................... 3-31
Ending Screen Display ........................ 4-87
Engine Coolant .......................................... 6-25
Engine compartment overview ..... 6-22
Exhaust gas.................................... 3-32
Hood release .................................. 6-20
Oil .................................................. 6-23
Starting ............................................ 4-5
Engine Coolant Temperature
Gauge ......................................... 4-15, 4-23
Essential Information ............................ 6-2
Event Data Recorder ........................... 8-21
Exhaust Gas ........................................ 3-32
Exterior Care ....................................... 6-56 Aluminum wheel maintenance ...... 6-61
Bright-metal maintenance ............. 6-60
Maintaining the fi nish ................... 6-58
Plastic part maintenance ................ 6-62
F
Flasher Hazard warning ............................. 4-65
Headlights ..................................... 4-51
Flat Tire ................................................. 7-3 Mounting the spare tire ................. 7-11
Removing a fl at tire ......................... 7-7
Floor Mat ............................................ 3-51 Fluid
Brake/Clutch ................................. 6-27
Washer ........................................... 6-27
Fluids Classifi cation ................................... 9-5
Fog Lights ........................................... 4-57
Foot Brake ........................................... 4-70
Forward Sensing Camera (FSC) ....... 4-156
Front Seat .............................................. 2-5
Fuel Filler lid and cap............................ 3-33
Gauge ................................... 4-15, 4-23
Requirements................................. 3-30
Tank capacity .................................. 9-5
Fuel Consumption Display ................. 4-87
Fuel Economy Monitor ....................... 4-86 Ending screen display ................... 4-87
Fuel consumption display ............. 4-87
Fuses ................................................... 6-50 Panel description ........................... 6-52
Replacement .................................. 6-50
G
Gauges ................................................. 4-12
Glove Compartment .......................... 5-145
H
Hazard Warning Flasher ...................... 4-65
Hazardous Driving .............................. 3-50
Head Restraint ..................................... 2-17
Headlights Coming home light ........................ 4-55
Control........................................... 4-51
Headlight fl ashing ......................... 4-54
High-low beam .............................. 4-54
Leaving home light ....................... 4-55
Leveling......................................... 4-56
High Beam Control System (HBC) .... 4-96 High Beam Control System (HBC)
indicator light (green) .................... 4-98
Hill Launch Assist (HLA) ................... 4-81
CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:07:42