2017 MAZDA MODEL CX-5 display

4–77
When Driving
Brake
CAUTION
If you stop operating the accelerator pedal before the vehicle starts moving, the force
holding the vehicle in the stopped position may weaken. Firmly depress the brake pedal
or depress the accelerator pedal to accelerate the vehicle.

NOTE
  Under the following conditions, a problem with the AUTOHOLD is occurring. Have your
vehicle inspected at an Authorized Mazda Dealer as soon as possible.
  The brake pedal operation request warning light (red) in the instrument cluster fl ashes
and the warning sound is activated for about fi ve seconds while the AUTOHOLD is
operating or when you press the AUTOHOLD switch.
   A message is indicated on the multi-information display and a warning sou\
nd is
activated for about fi ve seconds while the AUTOHOLD is operating or when your
press the AUTOHOLD switch.
   If the ignition is switched OFF while the AUTOHOLD is still operating, the electric
parking brake (EPB) is applied automatically shift lever is shifted to\
R.
  (Automatic transaxle vehicle)  The AUTOHOLD is canceled when the shift lever is shifted to R while the vehicle\
is on
level ground, or facing up a hill or grade (as shown below).

Level ground
: Driving in reverse (selector lever in R)
Vehicle tilts forward Vehicle tilts rearward
AUTOHOLD :
Operates AUTOHOLD :
Does not operate,
canceled
AUTOHOLD :
Does not operate,
canceled

CX-5_8FN1-EA-16L_Edition1.indb 772016/12/12 10:06:01

4–80
When Driving
Brake
AUTOHOLD System is Turned Off
The vehicle is driven
Press the AUTOHOLD switch to turn off
the AUTOHOLD ( AUTOHOLD standby
indicator light turns off).
Brakes are held
Depress the brake pedal and press the
AUTOHOLD switch to turn off the
AUTOHOLD (AUTOHOLD standby
indicator light and AUTOHOLD active
indicator light in instrument cluster turn
off).

AUTOHOLD standby
indicator light

NOTE
  (Without multi-information display)  If the AUTOHOLD switch is pressed
without depressing the brake pedal
while the AUTOHOLD is operating
(AUTOHOLD active indicator light is
turned on), the brake pedal operation
request indicator light (green) in the
instrument cluster turns on to notify the
driver that it is necessary to depress the
brake pedal.

(Green)  (With multi-information display)  If the AUTOHOLD switch is pressed
without depressing the brake pedal
while AUTOHOLD is operating
(AUTOHOLD active indicator light
in instrument cluster is turned on),
the message Depress Brake Pedal to
Release Parking Brake is indicated on
the multi-information display to notify
the driver to depress the brake pedal.
  If any of the following conditions
occurs while the AUTOHOLD function
is operating (AUTOHOLD active
indicator light is turned on), the
electric parking brake (EPB) is applied
automatically and the AUTOHOLD
function turns off. For the electric
parking brake (EPB) operation, refer
to the electric parking brake (EPB) on
page 4-71 .
  The ignition is switched OFF.  There is a problem with the
AUTOHOLD function.


CX-5_8FN1-EA-16L_Edition1.indb 802016/12/12 10:06:01

4–86
When Driving
Fuel Economy Monitor
*Some models.
Fuel Economy Monitor *
For vehicles with type B audio, the Fuel Consumption are switched and di\
splayed by
operating each icon in the display.
In addition, after completing a trip, the total energy effi ciency to date is displayed in the
ending display when the ending display is turned on.

1. Select the icon on the home screen to display the applications screen.
2. Select the “Fuel Economy Monitor”.
3. Operate the commander switch or touch the screen and display the menu.
NOTE
When the menu is displayed by touching the screen, the display is hidden automatically after
6 seconds.

4. Select the icon in the menu and perform the operation. Each icon operate\
s as follows:

Indication on display Control status


Hides the menu display.

Displays the application screen.

Switches the Fuel Economy Monitor in the order of Fuel Consumption.

Resets the fuel economy data.

Displays the following setting screen.  Ending display on/off switching
 On/off switching for function which synchronizes
reset fuel economy data to trip meter (Trip A)
(Type B instrument cluster only)

NOTE
The fuel economy monitor screen after the ignition is switched from ON to OFF is changed
to the original fuel economy monitor screen when the ignition is switched ON the next time.

CX-5_8FN1-EA-16L_Edition1.indb 862016/12/12 10:06:02

4–87
When Driving
Fuel Economy Monitor
Fuel Consumption Display
Information regarding the fuel economy is displayed.

Indication on display Control status


Displays the fuel economy for the past 60 minutes.  Displays the fuel economy every minute for the
past 1 to 10 minutes.

 Displays the fuel economy every 10 minutes for the
past 10 to 60 minutes.

Displays the average fuel economy over the past 5 resets and after the current reset.

Calculates the average fuel economy every minute after vehicle travel begins, and displays it.

NOTE
   The fuel economy data can be reset by doing the following operation:   Press the reset switch from the menu screen.  When the function which synchronizes the fuel economy monitor and the trip meter is
on, reset trip A of the trip meter.
  Delete the average fuel economy information displayed in the trip comput\
er.   After resetting the fuel economy data, “-- -” is displayed while the aver\
age fuel economy
is calculated.

Ending Screen Display
If the ending display on the fuel economy monitor is on when the ignitio\
n is switched from
ON to OFF, the information regarding the fuel economy is displayed.
CX-5_8FN1-EA-16L_Edition1.indb 872016/12/12 10:06:03

4–99
When Driving
i-ACTIVSENSE
*Some models.
Blind Spot Monitoring (BSM) *
The Blind Spot Monitoring (BSM) is designed to assist the driver in ch\
ecking the area to the
rear of the vehicle on both sides during lane changes by notifying the d\
river of the presence
of vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) detects vehicles approaching from the \
rear while
traveling in the forward direction at a speed of 10 km/h (6.3 mph) or \
faster and notifi es
the driver by turning on the Blind Spot Monitoring (BSM) warning indic\
ator light and
displaying the vehicle detection screen (vehicles with multi-informatio\
n display and active
driving display).
If the turn signal lever is operated to signal a turn in the direction i\
n which the Blind Spot
Monitoring (BSM) warning indicator light is illuminated while the appr\
oaching vehicle is
detected, the Blind Spot Monitoring (BSM) noti fi es the driver of possible danger by turning
on the Blind Spot Monitoring (BSM) warning indicator light, and by act\
ivating the warning
sound and the warning screen indicator display (vehicles with multi-inf\
ormation display and
active driving display).
The detection area on this system covers the driving lanes on both sides\
of the vehicle and
from the rear part of the front doors to about 50 m (164 ft) behind th\
e vehicle.

Detection areas
Your vehicle

WARNING
Always check the surrounding area visuall
y before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning indicator light, the warning sound and the warning
screen indicator display may not activate or they might be delayed even though a vehicle
is in an adjacent driving lane. Always make it your responsibility as a driver to check the
rear.

CX-5_8FN1-EA-16L_Edition1.indb 992016/12/12 10:06:05

4–101
When Driving
i-ACTIVSENSE
  In the following case, the fl ashing of the Blind Spot Monitoring (BSM) warning indicator
light, and the activation of the warning sound and the warning screen indicator display
may not occur or they may be delayed.
   A vehicle makes a lane change from a driving lane two lanes over to an adjacent lane.  Driving on steep slopes.  Crossing the summit of a hill or mountain pass.  When there is a difference in the height between your driving lane and the adjacent
lane.
  Directly after the Blind Spot Monitoring (BSM) system becomes operable by\
changing
the setting.
  If the road width is extremely narrow, vehicles two lanes over may be detected.
The detection area of the radar sensors (rear) is set according to the road width of
expressways.
  The Blind Spot Monitoring (BSM) warning indicator light may turn on an\
d the vehicle
detection screen may be displayed in the display in reaction to stationary objects
(guardrails, tunnels, sidewalls, and parked vehicles) on the road or the roadside.

Objects such as guardrails and concrete walls
running alongside the vehicle. Places where the width between guardrails or
walls on each side of the vehicle narrows.


The walls at the entrance and exits of tunnels
and turnouts.
   A Blind Spot Monitoring (BSM) warning indicator light may fl ash or the warning beep
may be activated several times when making a turn at a city intersection\
.
   Turn off the Blind Spot Monitoring (BSM) while pulling a trailer or whi\
le an accessory
such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the radar’s
radio waves will be blocked causing the system to not operate normally.
  In the following cases, it may be dif fi cult to view the illumination/ fl ashing of the Blind
Spot Monitoring (BSM) warning indicator lights equipped on the door mi\
rrors.
   Snow or ice is adhering to the door mirrors.  The front door glass is fogged or covered in snow, frost or dirt.
CX-5_8FN1-EA-16L_Edition1.indb 1012016/12/12 10:06:05

4–102
When Driving
i-ACTIVSENSE
  If a vehicle with the Blind Spot Monitoring (BSM) system is driven in \
a country other than
the U.S.A., Canada, or Mexico, the system has to be turned off by changi\
ng the setting on
the center display.
  The system switches to the Rear Cross Traffi c Alert function when the selector lever is
shifted to the reverse (R) position.
 Refer to Rear Cross Traffi c Alert (RCTA) on page 4-117 .
Blind Spot Monitoring (BSM) Warning Indicator Light/Display Indicator/
Blind Spot Monitoring (BSM) Warning Beep
The Blind Spot Monitoring (BSM)or Rear Cross Traf fi c Alert (RCTA) system noti fi es the
driver of the presence of vehicles in adjacent lanes or at the rear of t\
he vehicle using the
Blind Spot Monitoring (BSM) warning indicator light, the warning sound\
and the display
indicator (vehicles with multi-information display and active driving d\
isplay) while the
systems are operational.
Blind Spot Monitoring (BSM) warning indicator lights
The Blind Spot Monitoring (BSM) warning indicator lights are equipped \
on the left and
right door mirrors. The warning indicator lights turn on when a vehicle approaching from
the rear in an adjacent lane is detected.


When the ignition is switched ON, the warning indicator light turns on m\
omentarily and
then turns off after a few seconds.
Forward driving (Blind Spot Monitoring (BSM) operation)
The Blind Spot Monitoring (BSM) detects vehicles approaching from the \
rear and turns on
the Blind Spot Monitoring (BSM) warning indicator lights equipped on t\
he door mirrors
according to the conditions. Additionally, while a Blind Spot Monitoring (BSM) warning
indicator light is illuminated, if the turn signal lever is operated to \
signal a turn in the
direction in which the Blind Spot Monitoring (BSM) warning indicator l\
ight is illuminated,
the Blind Spot Monitoring (BSM) warning indicator light fl ashes.
CX-5_8FN1-EA-16L_Edition1.indb 1022016/12/12 10:06:05

4–103
When Driving
i-ACTIVSENSE
Reverse driving (Rear Cross Traffi c Alert (RCTA) system operation)
The Rear Cross Traf fi c Alert (RCTA) system detects vehicles approaching from the left and
right of your vehicle and fl ashes the Blind Spot Monitoring (BSM) warning indicator lights.
Function for cancelling illumination dimmer
If the Blind Spot Monitoring (BSM) warning indicator lights turn on when the parking lights
are turned on, the brightness of the Blind Spot Monitoring (BSM) warni\
ng indicator lights is
dimmed.
If the Blind Spot Monitoring (BSM) warning indicator lights are dif fi cult to see due to
glare from surrounding brightness when traveling on snow-covered roads o\
r under foggy
conditions, press the dimmer cancellation button to cancel the dimmer an\
d increase the
brightness of Blind Spot Monitoring (BSM) warning indicator lights whe\
n they turn on.
Refer to Dashboard Illumination on page 4-16 .
Display indicator (Vehicles with multi-information display and active driving display)
The detected approaching vehicle and warning are displayed in the multi-\
information
display and active driving display when the vehicle is moving forward (\
Blind Spot
Monitoring (BSM) operational).

Multi-information Display Active Driving Display
Detection and warning indicator Detection and warning indicator

The detected direction is displayed with a detection indicator (white)\
when an approaching
vehicle is detected. In addition, if the turn signal lever is operated t\
o signal a lane change
while the vehicle is detected, the display changes the color (amber) o\
f the warning indicator.
Blind Spot Monitoring (BSM) warning beep
The Blind Spot Monitoring (BSM) warning beep is activated simultaneous\
ly with the
fl ashing of a Blind Spot Monitoring (BSM) warning indicator light.
CX-5_8FN1-EA-16L_Edition1.indb 1032016/12/12 10:06:06