2017 MAZDA MODEL CX-5 change time

3–19
Before Driving
Doors and Locks
Settings can be changed using the
following procedure.

1. Safely park the vehicle. All doors must remain closed.
2. Switch the ignition ON.
3. Press and hold the lock side of the driver's door-lock switch within
20 seconds of switching the ignition
ON, and make sure a beep sound is
heard about eight seconds afterwards.
4. Refer to the auto lock/unlock function setting table, determine the function
number for the desired setting. Press
the unlock side of the driver's door-lock
switch the same number of times as the
selected function number (Ex. If you
select function 2, press the unlock side
of the switch only 2 times).
5. Three seconds after the function setting has been changed, a beep sound will
beep in the amount of the selected
function number. (Ex. Function number
3 = 3 beep sounds)

(Manual transaxle vehicles)

Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Function Number 3 Press 4 times
Press unlock side of
lock switch once
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
Wait for 3 second
(Automatic transaxle vehicles)


Press unlock side of
lock switch once
Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Press 4 times
Function Number 3
Press 5 times
Function Number 4
Press 7 times
Function Number 5
Press 6 times
Function Number 6
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
Wait for 3 second

NOTE
   The doors cannot be locked or unlocked
while the setting function is being
performed.
  The procedure can be cancelled by
pressing the lock side of the driver's
door-lock switch.

CX-5_8FN1-EA-16L_Edition1.indb 192016/12/12 10:05:31

3–27
Before Driving
Doors and Locks
Operation from outside (To open)
Press the electric liftgate opener on the
liftgate and raise the liftgate. The hazard
warning lights fl ash twice and the liftgate
opens automatically after the beep sound
is heard.
(With the advanced keyless function)
A locked liftgate can also be opened while
the key is being carried.

Electric liftgate
opener

Operation from outside (To close)
Press the power liftgate close switch while
the liftgate is fully opened. The hazard
warning lights fl ash twice and the liftgate
closes automatically after the beep sound
is heard.

Power liftgate
close switch

NOTE
If the power liftgate switch/power liftgate
close switch is pressed or the electric
liftgate opener is operated while the
liftgate is opening/closing electrically, the
beep sound is heard and the liftgate stops.
Then, it reverses when any of the switches
are pressed again.

Changing the power liftgate fully open
position
The power liftgate fully-open position can
be changed according to the height of a
garage.
When changing the position
1. Stop the liftgate at the desired position.
2. Press the power liftgate close switch for about three seconds.
A beep sound is activated two times to indicate that the position change has
been completed.

NOTE
Set the desired fully-open position of the
liftgate at the position where it is open
more than halfway. The position where it
is less than halfway open cannot be set.

To reset
1. Open the liftgate.
2. Press the power liftgate close switch for about seven seconds.
A beep sound is activated three times to indicated that the reset has been
completed.

CX-5_8FN1-EA-16L_Edition1.indb 272016/12/12 10:05:33

3–28
Before Driving
Doors and Locks
NOTE
After about 3 seconds have elapsed since
the switch was pressed, a beep sound
is activated 2 times to indicate that the
liftgate fully-open position has changed.
Continuously press the switch for about
7 seconds to complete the reset.

Jam-safe equipment
While the power liftgate is opening/
closing electrically and the system detects
a person or an object in the liftgate's
path, the liftgate will move in the reverse
direction automatically and stops.
WARNING
Always check the area around the
power liftgate before opening/closing it: Not checking for occupants and
objects around the power liftgate
before opening/closing it is dangerous.
The jam-safe equipment is designed
to prevent jamming in the event an
obstruction is in the liftgate's path. The
system may not detect certain objects
obstructing the liftgate depending
on the way they are positioned and
their shape. However, if the jam-safe
function detects an obstruction and
moves the liftgate in the reverse
direction, an occupant in the liftgate's
path could be seriously injured.

CAUTION
Sensors are installed on both ends of
the power liftgate. Be careful not to
allow the sensors to be scratched or
damaged by sharp objects, otherwise
the liftgate may no longer open/close
automatically. In addition, if the sensor
is damaged while the liftgate is closing
automatically, the system will stop.

Sensor

NOTE
The jam-safe equipment does not activate
during easy closure operation when the
power liftgate is between the near-shut
position and fully closed position.

When the power liftgate is moving in the
open/close direction and an obstruction is
detected, the beep sound will be heard and
the liftgate moves in the reverse direction
and stops.
CX-5_8FN1-EA-16L_Edition1.indb 282016/12/12 10:05:33

3–61
Before Driving
Towing
Trailer Towing Tips
  Verify that your Mazda maintains a near-normal attitude when a loaded or unloaded trailer
is connected. Do not drive if it has an abnormal front-up or front-down \
position. Inspect
for incorrect tongue load, worn suspension parts, and trailer overloadin\
g.
   Make sure the trailer is properly loaded and the cargo is secure to prevent it from shifting.  Make sure the mirrors conform to all government regulations. If they do \
not, install
required rear view mirrors appropriate for towing purposes.

The three main causes of vehicle-trailer accidents are driver error, excessive speed, and
improper trailer loading.
Before driving
   Have your cooling and braking system checked by an Authorized Mazda Dealer.  Before starting out, inspect the operation of all vehicle and trailer li\
ghts and all vehicle-
to-trailer connections. Stop and re-inspect all lights and connections a\
fter driving a short
distance.

Driving
   Your Mazda will handle differently with a trailer in tow, so practice turning, backing, and
stopping in a traf fi c-free area.
   Take time to get accustomed to the extra weight and length.  Allow more room between your vehicle and the one in front because brakin\
g distance
increases with a trailer. For each 16 km/h (10 mph) of speed, allow at least one vehicle
and trailer length between your Mazda and the vehicle ahead.
   Avoid jerky starts or sudden acceleration.  Avoid sudden braking. It may cause loss of control and result in jackkni fi ng, especially so
on wet or slippery roads.
   Shift the shift lever to the D position when towing a trailer in hilly t\
errain or when heavily
loaded.

The D position will allow operating the vehicle without frequent shiftin\
g.
Lane changes and turning
Avoid quick lane changes, sudden turns, and tight turns. Slow down before\
turning to avoid
the need of sudden braking.
A turning trailer will make a tighter arc than the tow vehicle. Compensat\
e with turns that are
larger than normal.
CX-5_8FN1-EA-16L_Edition1.indb 612016/12/12 10:05:39

4–17
When Driving
Instrument Cluster and Display
NOTE
  (With Multi-information Display)  The illumination dimmer can be
canceled by pressing the dashboard
illumination knob.
  When the illumination dimmer is
canceled, the instrument cluster cannot
be dimmed even if the position lights are
turned on.
  When the illumination dimmer is
canceled, the screen in the center
display switches to constant display of
the daytime screen.

Outside Temperature Display (Without Multi-information
Display)
When the ignition is switched ON, the
outside temperature is displayed.



NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and vehicle
conditions:
  Signifi cantly cold or hot temperatures.  Sudden changes in outside temperature.  The vehicle is parked.  The vehicle is driven at low speeds.

Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and Fahrenheit.
Settings can be changed by operating the
center display screen.
Refer to Personalization Features on page
9-11 .
NOTE
When the temperature unit indicated in the
outside temperature display is changed,
the temperature unit indicated in the
engine coolant gauge display changes in
conjunction with it.

Cruise Control Set Vehicle Speed
Display (Without Multi-
information Display)
The vehicle speed preset using the cruise
control is displayed.



Trip Computer and INFO Switch (Without Multi-information
Display)
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
   Distance-to-empty mode  Average fuel economy mode  Current fuel economy mode  Compass mode
If you have any problems with your trip
computer, consult an Authorized Mazda
Dealer.
CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:05:43

4–21
When Driving
Instrument Cluster and Display
The screen content changes each time the INFO switch is pressed.
Press the INFO switch Press the INFO switch
Press the INFO switch Press the INFO switch
Press the INFO switch Press the INFO switch
Current Fuel Economy,
Trip Meter A, Average
Fuel Economy, Outside
Temperature,
Odometer,
Distance-to-empty,
Fuel Gauge
Current Fuel Economy,
Trip Meter B, Average
Fuel Economy, Outside
Temperature,
Odometer,
Distance-to-empty,
Fuel Gauge
Engine Coolant
Temperature Gauge,
Maintenance
Monitor, Outside
Temperature,
Odometer,
Distance-to-empty,
Fuel Gauge i-ACTIVSENSE display,
Outside Temperature,
Odometer,
Distance-to-empty, Fuel
Gauge Compass, Outside
Temperature,
Odometer,
Distance-to-empty,
Fuel Gauge Warning message,
Outside Temperature,
Odometer,
Distance-to-empty,
Fuel Gauge
*1
*2
*1:Displayed only when a warning occurs.
*2:Displayed only while vehicle is being driven.

CX-5_8FN1-EA-16L_Edition1.indb 212016/12/12 10:05:44

4–23
When Driving
Instrument Cluster and Display
Engine Coolant Temperature Gauge
Displays the engine coolant temperature.
The blue gauge indicates that the engine
coolant temperature is low, and the red
gauge indicates that the engine coolant
temperature is high and overheating.


CAUTION
If the high engine coolant temperature
warning light (red) turns on, there is
a possibility of overheating. Park the
vehicle in a safe place immediately
and take appropriate measures. If the
vehicle continues to be driven, it could
cause damage to the engine.
Refer to Overheating on page 7-18 .

NOTE
  The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with
the temperature unit of the outside
temperature display.
 Refer to Personalization Features on page 9-11 .
  During normal driving, the engine
coolant temperature stabilizes at
100 °C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F).
  If the engine load increases and the
engine coolant temperature exceeds
100 °C (210 °F), the gauge indicates the
engine coolant temperature.

Fuel Gauge
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full.


Full
1/4 Full
Empty

If the fuel level is low, (
) and ( ) turn an
amber color. Refuel as soon as possible.
Refer to Taking Action on page 7-31 .
NOTE
   After refueling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve since
the fuel moves in the tank.
  The display indicating a quarter or less
remaining fuel has more segments to
show the remaining fuel level in greater
detail.
  The direction of the arrow ( )
indicates that the fuel- fi ller lid is on the
left side of the vehicle.

CX-5_8FN1-EA-16L_Edition1.indb 232016/12/12 10:05:44

4–25
When Driving
Instrument Cluster and Display
Average Fuel Economy
The average fuel economy is calculated
every minute from the total traveled
distance on the trip meter and the total
fuel consumption, and the average fuel
economy for either TRIP A or TRIP B is
displayed.


The average fuel economy and trip
meters can be reset by pressing the INFO
switch for 1.5 s or more while in each
mode. After the data is cleared, the fuel
consumption is recalculated and the
- - - L/100 km (- - - mpg) for the one
minute prior to it being displayed is
indicated.
Current Fuel Economy
This displays the current fuel economy
by calculating the amount of fuel
consumption and the distance traveled.



Maintenance Monitor
The following maintenance period
notifi cations can be displayed by turning
the Maintenance Monitor on.
   Scheduled Maintenance  Tire Rotation  Oil Change
For the setting method and indications
for the maintenance monitor, refer to the
Maintenance Monitor.
Refer to Maintenance Monitor on page
6-16 .
The maintenance monitor displays the
information when the ignition is switched
ON.
NOTE
This function is inoperable while the
vehicle is being driven.

Message display
When the remaining time or the distance
approaches 0, a message is displayed each
time the ignition is switched ON.


CX-5_8FN1-EA-16L_Edition1.indb 252016/12/12 10:05:45