2017 MAZDA MODEL CX-5 engine oil

(Europe)
(Except Europe)
GradeTe m
perature Range SAE Viscosity Numbers
ACEA C3
–30 –20 –10 0 1020 30
40
–200
20 40
60 80100
–40
–40
SKYACTIV-D 2.2
Te m perature Range SAE Viscosity Numbers
Grade
Mazda Original Oil Ultra DPF 5W -30
Mazda Original Oil Supra DPF 0W
-30
Alternati ve Oil Quality
Recommended oils
–30 –20 –10 0
1020 30
40
–200
20 40
60 80100
–40
–40
ACEA C3 5W-30
0W
-30
Engine oil viscosity, or thickness, has an effect on fuel econo my and cold-weather operation
(starting and oil flow).
Low-viscosity engine oils can pr ovide improved fuel economy and cold-weather
performance.

When choosing an oil, consider the temperature range your vehic le will operate in before
the next oil change.
Then select the recommended viscosity from the chart.
CAUTION
 Using oils of viscosity besides those recom mended for specific temperature ranges could
result in engine damage.
Maintenance and Care
Owner Maintenance
6-26
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

(SKYACTIV-D 2.2)
SKYACTIV-D 2.2 uses specified oil. Please confirm the specification in owner's manual. If
engine oil other than the specified oil is used, the Diesel Particulate Filter
effective period of
use will be shortened or the Diesel Particulate Filter may be damaged.
NOTE
(SKYACTIV-G 2.0 and SKYACTIV-G 2.5)
•It is normal for all engines to consume engine oil under normal driving conditions.
Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This may be as
a result of evaporation, internal ventilation or burning of the lubricating oil in the
working engine. Oil consumption may be high er when the engine is new due to the
running-in process. Oil consumption is also dependant on engine speed and engine load.
Under extreme driving conditions, oil consumption may be higher.
(SKYACTIV-D 2.2)
•Whenever the engine oil is replaced, the vehicles engine control unit needs to be reset as
soon as possible. Otherwise the wrench indi cator light or engine oil warning light may
turn on. To reset the engine control unit, consult an expert repairer, we recommend an
Authorised Mazda Repairer or refer to the vehicle engine control unit reset procedure on
page 6-27.
•Inspect the engine oil level periodically. When inspecting the engine oil, if the engine oil
level is exceeds the “X” mark on the dipstick, replace the engine oil. This should be done
by an expert repairer, we recommend an Authorised Mazda Repairer. When replacing the
engine oil, inspect the oil level using the oil dipstick and refill so that the engine oil level
is within the range between MIN and MAX as shown in the figure.

X Mark
MAX
MIN
▼ Vehicle Engine Control Unit Reset Procedure
NOTE
This procedure is intended for vehicles
with SKYACTIV-D 2.2 and vehicles with
SKYACTIV-G 2.0 or SKYACTIV-G 2.5 which the engine oil flexible maintenance setting is
selected.
After replacing the engine oil, have a repair shop such as an A uthorised Mazda Repairer
perform the initialization (engine oil data resetting) of the r ecorded value. If the value
recorded by the computer is not initialized, the wrench indicat or light may not turn off or it
may turn on earlie r than normal.
Maintenance and Care
Owner Maintenance
6-27
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the instrument panel illumination knob pressed, and press and hold the instrument panel illumination knob for about 5 seconds until the master
warning light
flashes.

Instrument panel illumination knob
3. After the master warning light flashes for several seconds, the initialization is
completed.
▼ Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal operating temperature.
3. Turn it off and wait at least 5 minutes for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
SKYACTIV-G 2.0 and
SKYACTIV-G 2.5

MAX
OK
MIN
Maintenance and Care
Owner Maintenance
6-28
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SKYACTIV-D 2.2

MINOK
MAX
X Mark
NOTE
(SKYACTIV-D 2.2)
When inspecting the engine oil level,
pull out the dipstick straight without
twisting. In addition, when inserting
the dipstick, always insert it without
twisting so that the “X” mark faces the
front of the vehicle.
5. Pull it out again and examine the level.
The level is normal if it is between the
MIN and MAX marks.
If it is near or below MIN, add enough
oil to bring the level to MAX.
CAUTION
Do not overfill the engine oil. This may
cause engine damage.
6. Make sure the O-ring on the dipstick is positioned properly before reinserting
the dipstick.
7. Reinsert the dipstick fully.
Engine Coolant
▼ Inspecting Coolant Level
WA R N I N G
Do not use a match or live flame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS HOT:
A hot engine is dangerous. If the engine has
been running, parts of the engine
compartment can become very hot. You
could be burned. Carefully inspect the
engine coolant in the coolant reservoir, but
do not open it.
Pull over to a safe location, then switch
the ignition off and make sure the fan is
not running before attempting to work
near the cooling fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running indefinitely even if the
engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either cooling
system cap when the engine and radiator
are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot out
under pressure and cause serious injury.
Maintenance and Care
Owner Maintenance
6-29
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Window and HeadlightWasher Fluid
▼Inspecting Washer Fluid Level
WA R N I N G
Use only windscreen washer fluid or plain
water in the reservoir:
Using radiator antifreeze as washer
fluid is
dangerous. If sprayed on the windscreen, it
will dirty the windscreen, affect your
visibility, and could result in an accident.
Inspect fluid level in the washer fluid
reservoir; add fluid if necessary.

L F
The top of the float should be between F
and L.

Use plain water if washer fluid is
unavailable.
But use only washer fluid in cold weather
to prevent it from freezing.
NOTE
Front and rear washer fluid is supplied
from the same reservoir.
Body Lubrication
All moving points of the body, such as
door and bonnet hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.

Make sure the bonnet's secondary latch
keeps the bonnet from opening when the
primary latch is released.
Maintenance and Care
Owner Maintenance
6-32
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•(19-inch wheel vehicle)
If your aluminium wheels lose lustre,
apply wax which contains no polishing
powder.
▼Plastic Part Maintenance
•When cleaning the plastic lenses of the
lights, do not use petrol, paraffin,
rectified spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a significant loss in
functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
•If plastic parts s
uch as the bumpers
become inadvertently exposed to
chemical agents or fluids such as petrol,
oil, engine coolant, or battery fluid, it
could cause discolouration, staining, or
paint peeling. Wipe off any such
chemical agents or fluids using a soft
cloth immediately.
•High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could defo rm plastic parts or
damage the paint.
•Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
•In addition, do not u se an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result in
deformation of plastic parts or paint
damage.
Interior Care
WA R N I N G
Do not spray water into the vehicle cabin:
Spraying water into the vehicle cabin is
dangerous as electrical devices such as the
audio and switches could get wet resulting
in a malfunction or vehicle fire.
NOTE
•Do not wipe the interior using alcohol,
chlorine bleach, or organic solvents
such as thinner, benzene, and petrol.
Otherwise, it may cause discolouration
or stains.
•Rubbing hard with a stiff brush or cloth
may cause damage.
If the vehicle interior becomes soiled by
any of the following, wipe it off
immediately using a soft cloth.
Leaving it uncleaned could cause
discolouration, stains, cracks, or peeling of
the coating, and it will make it hard to
wipe off later.
•Beverage or fragrance
•Grease or oil
•Soiling
Maintenance and Care
Appearance Care
6-66
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning
Electronic Brake Force
Distribution System Wa r n i n g If the electronic brake force di
stribution control unit determines that some compo-
nents are operating incorrectly , the control unit may illuminate the brake system
warning light and the ABS warni ng light simultaneously. The problem is likely to be
the electronic brake force distribution system.
WARNING
Do not drive with both the ABS warning light and brake warning light illuminated.
Have the vehicle towed to an expert repairer, we recommend an Authorised Mazda Re‐
pairer to have the brakes inspected as soon as possible:
Driving when the brake system warning li ght and ABS warning light are illuminated
simultaneously is dangerous.
When both lights are illuminate d, the rear wheels could lock more quickly in an emer‐
gency stop than under normal circumstances.
Charging System Warn- ing Indication/Warning Light If the warning light illuminates while driving, it indicates a
malfunction of the alter-
nator or of the charging system.
Drive to the side of the road and park off the right-of-way. Co nsult an expert repairer,
we recommend an Author ised Mazda Repairer.
CAUTION
Do not continue driving when the charging system warning light is illuminated be‐
cause the engine could stop unexpectedly.
Engine Oil Warning Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is
low. Otherwise, it could result in extensive
engine damage.
If the light illuminates or the w arning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way o n level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain b ack into the sump.
3. Inspect the engine oil level. (page 6-28) If it's low, add th e appropriate amount of
engine oil while being careful not to overfill.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.

If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-44
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Electrical System
Item Classification
SKYACTIV-G 2.0, SKYACTIV-G 2.5 SKYACTIV-D 2.2
Battery Q-85
*1T- 1 1 0*112V-55Ah/20HR*2 or 12V-65Ah/20HR*2
Spark-plug numberExcept Thailand
Mazda Genuine
spark plug*3
PE5R-18-110 or
PE5S-18-110 ―
Thailand PEHW-18–110
*1 Q-85 or T-110 is designed for i-stop system (FOR STOP & START)/i-ELOOP system. O nly Q-85 or T-110
should be used to ensure correct operation of i-stop system (FOR STOP & START)/i-ELOOP system. Consult
an expert repairer, we recommend an Authorised Mazda Repairer f or details.
*2 Not for i-stop system/i-ELOOP system.*3 The spark plugs provide the SKYACTIV-G its optimum performance. Consult an expert repairer, we
recommend an Authorised Mazd a Repairer for details.
CAUTION
When cleaning the iridium plugs, do not use a wire brush. The
fine particulate coating on the
iridium alloy and platinum tips could be damaged.
▼ Lubricant Quality
Engine oil*1Europe
Except Europe
SKYACTIV-G 2.0,
SKYACTIV-G 2.5 Recommended Oils
*2Oil Quality
Mazda Original Oil Supra 0W-20
API SL/SM/SN or
ILSAC GF-III/GF-IV/GF-V
Mazda Original Oil Ultra 5W-30
Alternative Oil Quality
*3
API SN*4 or ACEA A5/B5 0W-20
5W-30
SKYACTIV-D 2.2 Recommended Oils
*2Oil Quality
Mazda Original Oil Supra DPF 0W-30
ACEA C3
0W-30/5W-30
Mazda Original Oil Ultra DPF 5W-30
Alternative Oil Quality
*3
ACEA C3 0W-30
5W-30
*1 Refer to Recommended Oil on page 6-25.*2 Mazda Original Oils are special
ly designed/tested for the respective engine. For optimum performance we
recommend to use Mazda Ori ginal Oils at all times.
*3 If you are unable to find a Ma zda Original Oil, alternative oils meeting the listed sp ecification may also be
used.
*4 Use API SM/SN in Kazakhstan.
Specifications
Specifications
9-6
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2