2017 MAZDA MODEL CX-5 steering

Steering Wheel
WA R N I N G
Never adjust the steering wheel while the
vehicle is moving:
Adjusting the steering wheel while the
vehicle is moving is dangerous. Moving it
can very easily cause the driver to abruptly
turn to the left or right. This can lead to loss
of control or an accident.
▼Steering Wheel Adjustment
To change the angle or length of the
steering wheel:
1. Stop the vehicle, and then pull down
the lock release lever under the
steering column.

Lock release lever
2. Tilt the steering wheel and/or adjustthe steering column length to the
desired positions, then push the lever
up to lock the column.
3. Attempt to push th e steering wheel up
and down to make sure it's locked
before driving.
▼ Heated Steering Wheel*
The grips on the left and right of the
steering wheel can be warmed up.
Heated steering
wheel switch
Heating area
The ignition must be switched ON.

Press the switch to turn on the heated
steering wheel. The heated steering wheel
operates for about 30 minutes and then
turns off automatically.
The indicator light illuminates when the
heater is operating.

To turn off the heated steering wheel
before the 30 minutes has elapsed, press
the switch again.
CAUTION
The following types of persons should be
careful not to touch the steering wheel.
Otherwise, it could cause a
low-temperature burn.
 Infants, small children, elderly people,
and physically challenged people
 People with delicate skin
 People who are excessively fatigued
 People who are intoxicated
 People who have taken sleep-inducing
medicine such as sleeping pills or cold
medicine
Before Driving
Steering Wheel
*Some models.3-35
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Running-In
No special running-in is necessary, but a
few precautions in the first 1,000 km (600
miles) may add to the performance,
economy, and life of the vehicle.
•Do not race the engine.
•Do not maintain one constant speed,
either slow or fast, for a long period of
time.
•Do not drive constantly at full-throttle or
high engine rpm for extended periods of
time.
•Avoid unnecessary hard stops.
•Avoid full-throttle starts.
•Do not tow a trailer.
Saving Fuel and Protection of the Environment
How you operate your Mazda determines
how far it will travel on a tank of fuel. Use
these suggestions to help save fuel and
reduce CO
2.
•Avoid long warm-ups. Once the engine
runs smoothly, begin driving.
•Avoid fast starts.
•Drive at lower speeds.
•Anticipate when to apply the brakes
(avoid sudden braking).
•Follow the maintenance schedule (page
6-3) and have an expert repairer, we
recommend an Authorised Mazda
Repairer perform inspections and
servicing.
•Use the air conditioner only when
necessary.
•Slow down on rough roads.
•Keep the tyres properly inflated.
•Do not carry unnecessary weight.
•Do not rest your foot on the brake pedal
while driving.
•Keep the wheels in correct alignment.
•Keep windows closed at high speeds.
•Slow down when driving in crosswinds
and headwinds.
WA R N I N G
Never stop the engine when going down a
hill:
Stopping the engine when going down a
hill is dangerous. This causes the loss of
power steering and power brake control,
and may cause damage to the drivetrain.
Any loss of steering or braking control
could cause an accident.
Before Driving
Driving Tips
3-53
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Fuel Economy Monitor................... 4-96Fuel Economy Monitor
*............. 4-96
Drive Selection............................... 4-101 Drive Selection
*....................... 4-101
i-ACTIV AWD............................... 4-103 i-ACTIV AWD Operation
*...... 4-103
Power Steering...............................4-104 Power Steering......................... 4-104
i-ACTIVSENSE............................. 4-105 i-ACTIVSENSE....................... 4-105
Adaptive Front Lighting System
(AFS)
*...................................... 4-108
High Beam Control System
(HBC)
*......................................4-109
Adaptive LED Headlights
(ALH)
*...................................... 4-112
Blind Spot Monitoring (BSM)
*.........
.................................................. 4-115
Traffic Sign Recognition System
(TSR)
*...................................... 4-120
Distance Recognition Support
System (DRSS)
*....................... 4-127
Driver Attenti on Alert (DAA)
*..........
.................................................. 4-131
Rear Cross Traffic Alert (RCTA)
*.....
.................................................. 4-133
Mazda Radar Cruise Control
(MRCC) (Manual Transaxle and
Ta i w a n )
*................................... 4-137
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) (Automatic
Transaxle except Taiwan)
*....... 4-149
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS)
*.................................. 4-163
Adjustable Speed Limiter (ASL)
*......
.................................................. 4-174
Advanced Smart City Brake Support
(Advanced SCBS) (Except Indonesia
and Taiwan)
*............................ 4-181
Smart City Brake Support [Forward]
(SCBS F) (Indonesia and
Ta i w a n )
*................................... 4-185
Smart City Brake Support [Reverse]
(SCBS R)
*................................ 4-189
Smart Brake Support (SBS)
*.... 4-193
Forward Sensing Camera (FSC)
*......
.................................................. 4-196
Radar Sensor (Front)
*.............. 4-201
Radar Sensors (Rear)
*.............. 4-204
Ultrasonic Sensor (Rear)
*.........4-206
Cruise Control............................... 4-207 Cruise Control
*.........................4-207
Tyre Pressure Monitoring
System.............................................4-212 Tyre Pressure Monitoring
System
*..................................... 4-212
Diesel Particulate Filter................ 4-216 Diesel Particulate Filter
(SKYACTIV-D 2.2)..................4-216
Rear View Monitor....................... 4-217 Rear View Monitor
*................. 4-217
4-2*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Ignition Switch
▼Push Button Start Positions
The system operates only when the key is
within operational range.
Each time the push button start is pressed,
the ignition switches
in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Push button start
NOTE
•The engine starts by pressing the push
button start while depressing the clutch
pedal (manual transaxle) or the brake
pedal (automatic transaxle). To switch
the ignition position, press the push
button start without depressing the
pedal.
•Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the ignition is left in ACC (For
automatic transaxle, the selector lever is
in the P position, and the ignition is in
ACC), the ignition switches off
automatically after about 25 minutes.
Off
The power supply to electrical devices
turns off and the push button start
indicator light (amber) also turns off.
In this position the steering wheel is
locked.
WA R N I N G
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the selector lever is in
P (automatic transaxle) or in 1st gear or R
(manual transaxle):
Leaving the driver's seat without switching
the ignition off, setting the parking brake,
and shifting the selector lever to P
(automatic transaxle) or to 1st gear or R
(manual transaxle) is dangerous.
Unexpected vehicle movement could occur
which could result in an accident.
In addition, if your intention is to leave the
vehicle for even a short period, it is
important to switch the ignition off, as
leaving it in another position will disable
some of the vehicle's security systems and
run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is flashing and the beep sound is
heard, this indicates that the steering
wheel is not unlocked. To unlock the
steering wheel, press the push button start
while moving the steering wheel left and
right.
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
When Driving
Start/Stop Engine
4-4
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

In this position the steering wheel is
unlocked.
NOTE
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.
ON
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition is
switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-42).
NOTE
(SKYACTIV-G 2.0, SKYACTIV-G 2.5)
When the push button start is pressed to
ON, the sound of the fuel pump motor
operating near the fuel tank can be heard.
This does not indi cate an abnormality.
Starting the Engine
WA R N I N G
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who use
medical devices, ask the medical device
manufacturer or your physician if radio
waves from the key w ill affect the device.
NOTE
•The key must be carried because the key
carries an immobilizer chip that must
communicate with the engine controls at
short range.
•The engine can be started when the push
button start is pressed from off, ACC, or
ON.
•The push button start system functions
(function which can start the engine by
only carrying the key) can be
deactivated to prevent any possible
adverse effect on a user wearing a
pacemaker or other medical device. If
the system is deactivated, you will be
unable to start the engine by carrying
the key. Consult an expert repairer, we
recommend an Authorised Mazda
Repairer for details. If the push button
start system functions have been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9.
•After starting a cold engine, the engine
speed increases and a whining sound
from the engine compartment can be
heard.
When Driving
Start/Stop Engine
4-5
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Operation conditions
When the system is operable
Under the following conditions, engine idling stops and the i-stop indicator light (green)
turns on.
•(SKYACTIV-G 2.0, SKYACTIV-G 2.5)
The engine is warmed up.
•(SKYACTIV-D 2.2)
•The engine is not cold.
•The fuel injection amount learning, which is performed periodic ally and automatically,
is not being performed.
•The engine has been started and the vehicle is driven for a cer tain period.
•The engine is started with the bonnet closed.
•The battery is in good condition.
•All doors, liftgate, and bonnet are closed.
•The driver's seat belt is fastened.
•The air conditioner is not operating with the airflow mode dial in the position.
•(Automatic air-conditioning)
•The temperature setting dial of the air conditioner is in a position other than maximum
heating or maximum cooling (A/C ON) position.
•The vehicle's interior temperature and the set temperature for the air conditioner are
nearly the same.
•The i-stop warning light (ambe r) is not turned on/flashing.
•The keyless entry & push button start system functions are norm al.
•The brake vacuum is sufficiently high.
•The steering wheel is not being operated.
•(Manual transaxle)
•The vehicle speed is 3 km/h (1.8 mph) or less.
•The shift lever is in the neutral position.
•The clutch pedal is not depressed.
•(Automatic transaxle)
•The vehicle is stopped.
•The selector lever is in the D or M position (not in second gea r fixed mode).
•The automatic transaxle fluid has warmed up sufficiently.
•The automatic transaxle fluid temperature is not abnormally hig h.
•The steering wheel is almost in the straight-ahead position (idling may not stop even
with the steering wheel in the st raight-ahead position if force is applied to the steering
wheel. Release t he force applied to the steering wheel to stop engine idling).
•The vehicle is stopped by depressing the brake pedal.
When Driving
Start/Stop Engine
4-14
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•Emergency braking is not applied.
•When the vehicle is stopped by the Mazda Radar Cruise Control with Stop & Go
function (MRCC with Stop & Go function) stop hold control (vehi cles with Mazda
Radar Cruise Control with Stop & Go function (MRC C with Stop & Go function).
When the system is not operable
Engine idling does not stop in the following conditions:
•The vehicle is stopped but t he engine is kept idling.
•The air conditioner is operating with the airflow mode dial in the position.
•(Automatic air-conditioning)
•The temperature setting dial of the air conditioner is in the m aximum heating or
maximum cooling (A/C ON) position.
•There is a large difference between the cabin temperature and the set temperature of the
air conditioner.
•The ambient temperature is extremely high or low.
•The atmospheric pressure is low (when driving at high altitudes ).
•(Automatic transaxle)
•The vehicle is stopped on a steep incline.
•The steering wheel is not in the straight-ahead position while the vehicle is stopped.
•(SKYACTIV-D 2.2)
•The particulate matter (PM) is being removed by the diesel particulate filter (DPF).
•The fuel injection amount learning is being performed. (The i-stop indicator light
(green) turns off when the vehicle speed before stopping is app rox. 10 km/h (6.2 mph)
or less and fuel injection amount learning is performed while t he vehicle is stopped.)
NOTE
Under the following conditions, a period of time is required to stop engine idling
•The battery power is depleted for some reasons such as the vehicle has not been driven
for a long period.
•The ambient temperature is high or low.
•After the battery terminals are disconnected for some reasons such as for battery
replacement.
•(SKYACTIV-D 2.2)
After PM removal is performed by the diesel particulate filter (DPF).
Engine does not restart
If the following operations are performed while th e idling is stopped, the engine will not
restart for safety reasons. In such cases, start the engine using the normal method.
When Driving
Start/Stop Engine
4-15
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•(European model)
•The bonnet is opened.
•The driver's seat belt is unfastened and the driver's door is opened.
Engine-stop period is short or time until next engine idle stop is long
•The ambient temperature is high or low.
•The battery power is depleted.
•Power consumption by the vehicle's electrical parts is high.
Engine restarts automatically while engine idling is stopped
Under the following conditions, th e engine restarts automatically.
•The i-stop OFF switch is pressed until the beep sounds.
•The air conditioner is operated with the airflow mode dial in the position.
•(Automatic air-conditioning)
•The temperature setting dial of the air conditioner is in the maximum heating or
maximum cooling (A /C ON) position.
•The cabin temperature is largely different from the set temperature of the air
conditioner.
•The brakes are released slightly on a slope and the vehicle begins to move.
•Two minutes have elapsed since the idling was stopped.
•The battery power is depleted.
•(Automatic transaxle)
•The accelerator pedal is depressed with the selector lever in the D or M (not in second
gear fixed mode) position.
•The selector lever is shifted to the R position.
•The selector lever is shifted from N or P position to D or M (not in second gear fixed
mode) position.
•The steering wheel is operated with the selector lever in the D or M (not in second gear
fixed mode) position.
•The selector lever is in the M position and the second gear fixed mode is selected.
•(Except European model)
•(Manual transaxle)
With the shift lever in the neutral position, the driver's se at belt is unfastened, the
driver's door is opened, or the bonnet is opened.
•(Automatic transaxle)
With the selector lever in the P or N position, or the D/M range, the driver's seat belt is
unfastened, the driver's door is opened, or the bonnet is opened.
When Driving
Start/Stop Engine
4-16
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2