2017 MAZDA MODEL CX-5 height

•Cruise Control Operation Conditions
Refer to Cruise Control on page 4-207.
•Navigation Guidance (vehicles with navigation system)
•Speed limit indicator (vehicles with navigation system)
•Vehicle Speed
Each setting/adjustment for the active driving display can be p erformed on the centre
display.
1. Select the
icon on the home screen and display the Settings screen.
2. Select the AD-Disp tab.
3. Select the desired item and perform the setting/adjustment.
•Method for adjusting screen brightness (automatically/manually)
•Screen brightness initial settings (automatic adjustment is sel ected)
•Screen brightness adjustment (manual adjustment is selected)
•Display position of active driving display (display height)
•Active driving display angle adjustment (display angle correcti on) (With windscreen
type)
•Active driving display ON/OFF (indication)
•Navigation guidance ON/OFF
•Reset settings (reset)
NOTE
•The desired driving position (display position, brightness level, display information) can
be called up after programming the position.
Refer to Driving Position Memory on page 2-7.
When Driving
Instrument Cluster and Display
4-41
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•When there is a difference in the height between your driving lane and the adjacent
lane.
•Directly after the BSM system becomes operable by changing the setting.
•If the road width is extremely narrow, vehicles two lanes over may be detected. The
detection area of the radar sensors (rear) is set according to the road width of
expressways.
•The BSM warning indicator light may turn on and the vehicle detection screen may be
displayed in the display in reaction to stationary objects (guardrails, tunnels, sidewalls,
and parked vehicles) on the road or the roadside.
Objects such as guardrails and concrete walls
running alongside the vehicle. Places where the width between guardrails or
walls on each side of the vehicle narrows.
The walls at the entrance and exits of tunnels,
turnouts.
•A BSM warning indicator light may flash or the warning beep and the warning screen
indicator display may be activated several times when making a turn at a city
intersection.
•Turn off the BSM while pulling a trailer or wh
ile an accessory such as a bicycle carrier is
installed to the rear of the vehicle. Otherwise, the radar’s radio waves will be blocked
causing the system to not operate normally.
•In the following cases, it may be difficult to view the illumination/flashing of the BSM
warning indicator lights equipped on the door mirrors.
•Snow or ice is adhering to the door mirrors.
•The front door glass is fogged or covered in snow, frost or dirt.
•The system switches to the Rear Cross Traffi c Alert function when the shift lever (manual
transaxle) or the selector lever (automatic transaxle) is shifted to the reverse (R) position.
Refer to Rear Cross Traffic Alert (RCTA) on page 4-133.
When Driving
i-ACTIVSENSE
4-117
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Smart City Brake Support [Reverse] (SCBS R)*
The SCBS R is a system which is designed to reduce damage in the event of a collision by
operating the brake control (SCB S brake) when the system’s ultrasonic sensors detect an
obstruction at the rear of the vehicle while driving at a speed of about 2 to 8 km/h (2 to 4
mph) and the system determines that a collision is unavoidable.
Reverse Ultrasonic sensor (rear)
WA R N I N G
Do not rely completely on the SCBS R system:

The SCBS R system is only designed to red uce damage in the event of a collision. Over
reliance on the system leading to the accele rator pedal or brake pedal being mistakenly
operated could result in an accident.
 To assure the correct operation of the SCBS R, heed the following cautions.
 Do not apply a sticker to an ultrasonic sens or (rear) (including transparent stickers).
Otherwise, the ultrasonic sensor (rear) may no t be able to detect vehicles or obstructions
which could result in an accident.
 Do not disassemble an ultrasonic sensor (rear).
 If cracks or damage caused by flying gravel or debris is visible around an ultrasonic
sensor (rear), stop using the SCBS R system immediately and have your vehicle inspected
by an expert repairer, we recommend an Au thorised Mazda Repairer. If the vehicle
continues to be driven with cracks or scratch marks left around an ultrasonic sensor, the
system may operate unnecessarily an d cause an unexpected accident.
Refer to Stopping the Smart City Brake Supp ort [Reverse] (SCBS R) System Operation on
page 4-192.
 Consult an expert repairer, we recommend an Authorised Mazda Repairer for rear
bumper replacement.
Do not modify the suspension:
If the vehicle height or inclination is changed, the SCBS R system may not operate correctly
because it cannot detect obstructions correctly.
When Driving
i-ACTIVSENSE
*Some models.4-189
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Do not apply a strong force to an ultrasonic sensor (rear):
When washing the vehicle, do not spray highly pressurised water against an ultrasonic sensor
(rear), or rub it strongly. In addition, do not hit the rear bumper forcefully when loading and
unloading cargo Otherwise, the sensors may no t detect obstructions correctly which could
cause the SCBS R system to not operate no rmally, or it could operate unnecessarily.
CAUTION
When driving
off-road in areas where there is grass or foliage, it is recommended that the
SCBS R system be turned off.
 Always use tyres of the specified size and th e same manufacturer, brand, and tread pattern
on all 4 wheels. In addition, do not use tyres wi th significantly different wear patterns on the
same vehicle. Otherwise, the SCBS R system may not operate normally.
 If ice or snow is stuck on the ultrasonic sensors (rear) they may not be able to detect
obstructions correctly depending on the conditions. In such cases, the system may not be
able to perform controls correctly. Always dr ive carefully and pay attention to the rear of
the vehicle.
NOTE
•The vehicle posture changes depending on the accelerator pedal, brake pedal and
steering wheel operations, which could make it difficult for the system to recognise an
obstruction, or it could facilitate unnecessary detection. In such cases, the SCBS R may or
may not operate.
•The SCBS R system will operate under the following conditions.
•The engine is running.
•The change lever (manual transaxle vehicle) or the selector lever (automatic transaxle
vehicle) is in the R (reverse) position.
•“Reverse Smart City Brake Support Malfunction” is not displayed in the
multi-information display.
•The vehicle speed is between about 2 to 8 km/h (2 to 4 mph).
•The SCBS R is not turned off.
•The DSC is not malfunctioning.
•The SCBS R operates using ultrasonic sensors (rear) which detect obstructions at the rear
by emitting ultrasonic waves and then receiving the returning waves reflected off the
obstructions.
•In the following cases, the ultrasonic sensors (rear) cannot detect obstructions and the
SCBS R may not operate.
•The height of the obstruction is low such as low walls or trucks with low loading
platforms.
When Driving
i-ACTIVSENSE
4-190
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•The height of the obstruction is high such as trucks with high loading platforms.
•The obstruction is small.
•The obstruction is thin such as a signpost.
•The obstruction is positioned away from the centre of the vehicle.
•The surface of the obstruction is not pointed vertically relative to the vehicle.
•The obstruction is soft such as a hanging curtain or snow stuck to a vehicle.
•The obstruction is shaped irregularly.
•The obstruction is extremely close.
•In the following cases, the ultrasonic sensors (rear) cannot detect obstructions correctly
and the SCBS R may not operate.
•Something is stuck on the bumper near an ultrasonic sensor (rear).
•The steering wheel is turned sharply, or the brake or accelerator pedal is operated.
•There is another obstruction near one obstruction.
•During inclement weather such as rain, fog and snow.
•High or low humidity.
•High or low temperatures
•Strong winds.
•The path of travel is not flat.
•Heavy luggage is loaded in the luggage compartment or on the rear seat.
•Objects such as a wireless aerial, fog light , or illuminated number plate is installed
near an ultrasonic sensor (rear).
•The orientation of an ultrasonic sensor (rear) has deviated for reasons such as a
collision.
•The vehicle is affected by other sound waves such as the horn, engine noise, ultrasonic
sensor of another vehicle.
•In the following cases, an ultrasonic sensor (rear) may detect something as a target
obstruction which could cause the SCBS R system to operate.
•Driving on a steep slope.
•Wheel blocks.
•Hanging curtains, gate poles such as at toll gates and railroad crossing.
•When travelling near objects such as foliage, barriers, vehicles, walls, and fences along
a road.
•When driving off-road in areas where there is grass and forage.
•When passing through low gates, narrow gates, car washing machines, and tunnels.
•A towing bar is installed or a trailer is connected.
•(Manual transaxle)
If the vehicle is stopped by the Smart City Brake Support (SCBS) operation and the clutch
pedal is not depressed, the engine stops.
•When the system operates, the user is no tified by the multi-information display.
When Driving
i-ACTIVSENSE
4-191
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Forward Sensing Camera (FSC)*
Your vehicle is equipped with a Forward Sensing Camera (FSC). The Forward Sensing
Camera (FSC) is positioned near t he rearview mirror and used by the following systems.
•High Beam Control System (HBC)
•Adaptive LED Headlights (ALH)
•Driver Attention Alert (DAA)
•Lane-keep Assist System (LAS) & Lane Departure Warning System ( LDWS)
•Traffic Sign Recognition System (TSR)
•Advanced Smart City Brake Support (Advanced SCBS)
•Smart City Brake Support [Forward] (SCBS F)
•Mazda Radar Cruise Control with S top & Go function (MRCC with Stop & Go function)
•Smart Brake Support (SBS)
Forward Sensing Camera (FSC)
The Forward Sensing Camera (FSC) determines the conditions ahea d of the vehicle while
travelling at night and detects traffic lanes. The distance in which the Forward Sensing
Camera (FSC) can detect objects v aries depending on the surrounding conditions.
WA R N I N G
Do not modify the suspension:
If the vehicle height or inclination is changed, the system will not be able to correctly detect
vehicles ahead. This will result in the system not operating normally or mistakenly operating,
which could cause a serious accident.
CAUTION
 Do not apply accessories, stickers or film to the windscreen near the Forward Sensing
Camera (FSC).
When Driving
i-ACTIVSENSE
4-196*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Smart Brake Support (SBS)
 The direction in which the Forward Sensing Camera (FSC) is pointed has been finely
adjusted. Do not change the installation posi tion of the Forward Sensing Camera (FSC) or
remove it. Otherwise, it could result in damage or malfunction.
 Always use tyres for all wheels that are of the
specified size, and the same manufacturer,
brand, and tread pattern. In addition, do no t use tyres with significantly different wear
patterns on the same vehicle as the system may not operate normally.
 The Forward Sensing Camera (FSC) includes a function for detecting a soiled windscreen
and informing the driver, however, depending on the conditions, it may not detect plastic
shopping bags, ice or snow on the windscreen . In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive carefully
and pay attention to the road ahead.
NOTE
•In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
•The height of the vehicle ahead is low.
•You drive your vehicle at the same speed as the vehicle ahead.
•Headlights are not turned on during the night or when going through a tunnel.
•In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
•Under bad weather condition, such as rain, fog and snow.
•The window washer is being used or the windscreen wipers are not used when it's
raining.
•Ice, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on the
windscreen.
•Trucks with low loading plat forms and vehicles with an extremely low or high profile.
•When driving next to walls with no patterning (including fences and longitudinally
striped walls).
•The tail lights of the vehicle ahead are turned off.
•A vehicle is outside the illumi nation range of the headlights.
•The vehicle is making a sharp turn, or ascending or descending a steep slope.
•Entering or exiting a tunnel.
•Heavy luggage is loaded causing the vehicle to tilt.
•Strong light is shone at the front of the vehicle (back light or high-beam light from
on-coming vehicles).
•There are many light emitters on the vehicle ahead.
•When the vehicle ahead is not equipped with tail lights or the tail lights are turned off at
nighttime.
When Driving
i-ACTIVSENSE
4-198
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

•Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
•Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) warning indication
•Smart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
•If the Forward Sensing Camera (FSC) detects that the windscreen is dirty or foggy, the
system functions related to the Forward Sensing Camera (FSC) are temporarily stopped
and the following warning lights turn on. Ho wever, this does not indicate a problem.
Remove the dirt from the windscreen or press the defroster switch and defog the
windscreen.
•High Beam Control System (HBC) warning light (amber)
•Adaptive LED Headlights (ALH) warning light (amber)
•Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
•Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) warning indication
•Smart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
•If there are recognizable cracks or damage caused by flying gravel or debris on the
windscreen, always have the windscreen replaced. Consult an Authorised Mazda Repairer
for replacement.
•(With Advanced Smar t City Brake Support (Advanced SCBS))
•The Forward Sensing Camera (FSC) recognises pedestrians when all of the following
conditions are met:
•The height of a pedestrian is about 1 to 2 meters.
•An outline such as the head, both shoulders, or the legs can be determined.
•In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly:
•Multiple pedestrians are walking, or there are groups of people.
•A pedestrian is close to a separate object.
•A pedestrian is crouching, lying, or slouching.
•A pedestrian suddenly jumps into the road right in front of the vehicle.
•A pedestrian opens an umbrella, or is carrying large baggage or articles.
•A pedestrian is in a dark location such as during the night, or blends into the
background by wearing clothes matching the background colour.
When Driving
i-ACTIVSENSE
4-200
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2