2017 MAZDA MODEL CX-3 parking brake

4–201
When Driving
Tyre Pressure Monitoring System
Tyre Pressure Monitoring System
Initialization
In the following cases, system
initialization must be performed so that the
system operates normally.
 


 A tyre pressure is adjusted.



 Tyre rotation is performed.



 A tyre or wheel is replaced.



 The battery is replaced or completely
drained.
 


 The tyre pressure monitoring system
warning light is illuminated.


Initialization method

1. Park the car in a safe place and ¿ rmly
apply the parking brake.
2. Let the tyres cool, then adjust the tyre
pressure of all four (4) tyres to the
speci¿ ed pressure indicated on the tyre
pressure label located on the driver's
door frame (door open).
Refer to Tyres on page 9-9 .
3. Switch the ignition ON.
4. Press and hold the tyre pressure
monitoring system set switch and
verify that the tyre pressure monitoring
system warning light in the instrument
cluster À ashes twice and a beep sound
is heard once.


CAUTION
If the system initialization is performed
without adjusting the tyre pressure, the
system cannot detect the normal tyre
pressure and it may not illuminate the
tyre pressure monitoring system warning
light even if a tyre pressure is low, or
it may illuminate the light even if the
pressures are normal.
Adjust the tyre pressure on all four
tyres and initialize the system when
the warning light is turned on. If the
warning light turns on for a reason other
than a À at tyre, the tyre pressure of all
four tyres may have decreased naturally.
The system initialization will not be
performed if the switch is pressed while
the vehicle is being driven.

4–213
When Driving
Parking Sensor System
NOTE
  Do not install any accessories within the detection ranges of the sensors. It may affect
the system operation.
  Depending on the type of obstruction and the surrounding conditions, the detection
range of a sensor may narrow, or the sensors may not be able to detect obstructions.
  The system may not operate normally under the following conditions: 



 Mud, ice, or snow is adhering to the sensor area (Returns to normal operation when
removed).
 


 The sensor area is frozen (Returns to normal operation when the ice is thawed).



 The sensor is covered by a hand.



 The sensor is excessively shocked.



 The vehicle is excessively tilted.



 Under extremely hot or cold weather conditions.



 The vehicle is driven on bumps, inclines, gravel, or grass covered roads.



 Anything which generates ultrasound is near the vehicle, such as another vehicle's
horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle,
or another vehicle's sensors.
 


 The vehicle is driven in heavy rain or in road conditions causing water-splash.



 A commercially-available wing pole or an aerial for a radio transmitter is installed to
the vehicle.
 


 The vehicle is moving towards a tall or square curbstone.



 An obstruction is too close to the sensor. 

 Obstructions under the bumper may not be detected. Obstructions that are lower than
the bumper or thin which may have been initially detected but are no longer detected
as the vehicle approaches more closely.
  The following types of obstructions may not be detected: 



 Thin objects such as wire or rope



 Things which absorb sonic waves easily such as cotton or snow



 Angular shaped objects



 Very tall objects, and those which are wide at the top



 Small, short objects 

 Always have the system inspected at an expert repairer, we recommend an Authorised
Mazda Repairer if any shock is applied to the bumpers, even in a minor accident. If the
sensors are deviated, they cannot detect obstructions.
  The beeper which indicates a system malfunction may not be heard if the ambient
temperature is extremely cold, or mud, ice, or snow adheres to the sensor area.
Remove any foreign material from the sensor area.
  When installing a trailer hitch, consult an expert repairer, we recommend an
Authorised Mazda Repairer.

5–22
Interior Features
Before Using the Audio System
Type B (Without CD player)


USB port Auxiliary jack

Type B (With CD player)


USB port Auxiliary jack

Connecting a device
1. If there is a cover on the AUX jack or
USB port, remove the cover.
2. Connect the connector on the device to
the USB port.

Connecting with a connector lead
1. If there is a cover on the AUX jack or
USB port, remove the cover.
2. Connect the device plug/connector lead
to the auxiliary jack/USB port.

WARNING
Do not allow the connection plug cord
to get tangled with the parking brake
or the shift lever (manual transaxle)/
selector lever (automatic transaxle):
Allowing the plug cord to become
tangled with the parking brake or
the shift lever (manual transaxle)/
selector lever (automatic transaxle) is
dangerous as it could interfere with
driving, resulting in an accident.
CAUTION
Do not place objects or apply force to
the auxiliary jack/USB port with the
plug connected.
NOTE
  Insert the plug into the auxiliary jack/
USB port securely.
  Insert or pull out the plug with the
plug perpendicular to the auxiliary
jack/USB port hole.
  Insert or remove the plug by holding
its base.

6–3
Maintenance and Care
Scheduled Maintenance
S c h e d u l e d M a i n t e n a n c e
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
Emission control and related systems
The ignition and fuel systems are highly important to the emission control system and to
ef¿ cient engine operation. Do not tamper with them.
All inspections and adjustments must be made by an expert repairer, we recommend an
Authorised Mazda Repairer.
Europe
The maintenance monitor alerts regarding the next maintenance due. However, at least every
20,000 km or 12 months after the respective last maintenance the next maintenance is due.
Maintenance 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 12th

SKYACTIV-G 2.0
Spark plugs *1 Replace every 120,000 km (75,000 miles).
Air ¿ lter
*2 R R R R
Evaporative system (if installed) I I I I
SKYACTIV-D 1.5
Fuel ¿ lter D D R D D R D D R D D R
Fuel injection system
*3 I I I I
Air ¿ lter
*2 C C R C C R C C R C C R
SKYACTIV-G 2.0 AND SKYACTIV-D 1.5
Drive belts
*4 I I I I
Engine oil & ¿ lter
*5*6*7 R R R R R R R R R R R R
Cooling system I I I I I I
Engine coolant
*8 Replace at ¿ rst 200,000 km (125,000 miles) or 10 years; after that,
every 100,000 km (62,500 miles) or 5 years.
Fuel lines and hoses I I I I I I
Battery
*9 I I I I I I I I I I I I
Brake lines, hoses and connections I I I I I I I I I I I I
Brake À uid
*10 R R R R R R
Parking brake I I I I I I I I I I I I
Disc brakes I I I I I I I I I I I I
Steering operation and linkages I I I I I I
Manual transaxle oil Replace every 180,000 km (112,500 miles).

6–6
Maintenance and Care
Scheduled Maintenance
Except Europe
I s r a e l
Maintenance Interval Number of months or kilometres, whichever comes ¿ rst
Months 12 24 36 48 60 72 84 96 108 120 132 144
×1000 km 15 30 45 60 75 90 105 120 135 150 165 180
Spark plugs Replace every 120,000 km or 6 years.
Fuel ¿ lter Replace every 135,000 km.
Evaporative system (if installed) I I I
Fuel lines and hoses I I I I I I
Drive belts
*1 I I I I I I I I I I I I
Engine oil & oil ¿ lter *2 R R R R R R R R R R R R
Air ¿ lter *3 C C C R C C C R C C C R
Cooling system I I I I I I
Engine coolant
*4 Replace at ¿ rst 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Battery
*5 I I I I I I I I I I I I
Brake lines, hoses and connections I I I I I I I I I I I I
Brake À uid
*6 I R I R I R I R I R I R
Parking brake I I I I I I I I I I I I
Power brake unit (Brake booster) and hoses I I I I I I I I I I I I
Disc brakes I I I I I I I I I I I I
Steering operation and linkages I I I I I I
Rear differential oil
*7*8
Transfer oil *8
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I I I I I I I
Driveshaft dust boots I I I I
Exhaust system and heat shields Inspect every 75,000 km.
Bolts and nuts on chassis and body T T T T T T T T T T T T
Body condition (for rust, corrosion and
perforation) Inspect annually.
Cabin air ¿ lter (if installed) R R R R R R
Tyres (including spare tyre) (with inÀ ation
pressure adjustment)
*9 I I I I I I I I I I I I
Emergency À at tyre repair kit (if installed) *10 Inspect annually.

6–8
Maintenance and Care
Scheduled Maintenance
Russia/Belarus/Azerbaijan/Kazakhstan
Maintenance Interval Number of months or kilometres, whichever comes ¿ rst.
Months 12 24 36 48 60 72 84 96 108 120 132 144
×1000 km 15 30 45 60 75 90 105 120 135 150 165 180
Drive belts *1 I I I I I I I I I I I I
Engine oil Russia/
Belarus/
Kazakhstan
*2 R R R R R R R R R R R R
Azerbaijan *3 Replace every 5,000 km or 6 months.
Engine oil ¿ lter Russia/
Belarus/
Kazakhstan
*2 R R R R R R R R R R R R
Azerbaijan *4 Replace every 10,000 km or 12 months.
Cooling system I I I I I I
Engine coolant
*5 Replace at ¿ rst 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Air ¿ lter
*6 Russia/
Belarus/
Kazakhstan C C R C C R C C R C C R
Azerbaijan C R C R C R C R C R C R
Fuel ¿ lter Russia/
Belarus/
Kazakhstan Replace every 120,000 km.
Azerbaijan Replace every 60,000 km.
Fuel lines and hoses I I I I I I
Spark plugs I I I I I I I R I I I I
Evaporative system (if installed) I I I
Battery
*7 I I I I I I I I I I I I
Brake lines, hoses and connections I I I I I I I I I I I I
Brake À uid
*8 R R R R R R
Parking brake I I I I I I I I I I I I
Disc brakes I I I I I I I I I I I I
Steering operation and linkages I I I I I I I I I I I I
Manual transaxle oil R R
Rear differential oil
*9*10
Transfer oil *10
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I I I I I I I
Driveshaft dust boots I I I I I I I I I I I I
Exhaust system and heat shields I I I I I I I I I I I I
Bolts and nuts on chassis and body T T T T T T T T T T T T
Hinges and catches L L L L L L L L L L L L

6–11
Maintenance and Care
Scheduled Maintenance
Maintenance
Interval Number of months or kilometres (miles), whichever comes ¿ rst.
Months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96
×1000 km 10 20 30 40 50 60 70 80 90
100 110 120 130 140 150 160
×1000 miles 6.25 12.5 18.75 25 31.25 37.5 43.75 50 56.25 62.5 68.75 75 81.25 87.5 93.75 100
Engine oil *4*5 Except
below
countries R R R R R R R R R R R R R R R R
Georgia/
Armenia/
Cambodia/
Gabon/
Ghana/
Cameroon/
Burundi/
Mozambique
Replace every 5,000 km (3,125 miles) or 6 months.
Tanzania Replace every 3,000 km (1,875 miles) or 3 months.
Engine oil ¿ lter
*4 Except
below
countries R R R R R R R R R R R R R R R R
Georgia/
Armenia/
Cambodia Replace every 10,000 km (6,250 miles) or 1 year. Gabon/
Ghana/
Cameroon/
Burundi/
Mozambique
Replace every 5,000 km (3,125 miles) or 6 months.
Tanzania Replace every 3,000 km (1,875 miles) or 3 months.
Cooling system I I I I I I I I
Engine coolant
*6 Replace at ¿ rst 200,000 km (125,000 miles) or 10 years; after that, every
100,000 km (62,500 miles) or 5 years.
Air ¿ lter
*7 Except
below
countries C C R C C R C C
Georgia/
Armenia C R C R C R C R
Fuel lines and hoses I I I I I I I I
Battery
*8 I I I I I I I I
Brake lines, hoses and connections I I I I I I I I
Brake À uid
*9 I I I R I I I R I I I R I I I R
Parking brake I I I I I I I I I I I I I I I I
Power brake unit (Brake booster)
and hoses I I I I I I I I
Disc brakes I I I I I I I I I I I I I I I I
Steering operation and linkages I I I I I I I I
Manual transaxle oil R

7–13
If Trouble Arises
Mazda ERA-GLONASS (Russia)
Method to start test mode
Switch the ignition ON while the parking brake is applied, and wait two minutes with the
vehicle stopped.
After that, perform the following procedure.

Move the signal lever up to right
turn
Move the signal lever up to right
turnMove the signal lever down
to left turn
Move the signal lever down
to left turn Return the signal lever to offReturn the signal lever to off
Return the signal lever to off
Return the signal lever to off Return the signal lever to off Move the signal lever up to right
turnWithin five seconds
Within one second Within one second Within one second Within one second
Within one second
Within one second
Within one second
Within one second Within five seconds
Within five second
Within one second Turn on the hazard warning
lights.
Turn off the hazard warning
lights.
Both red and green Mazda
ERA-GLONASS switch
indicator lights turn on.
Press the Mazda
ERA-GLONASS switch for
one second or longer and
release it.