2017 MAZDA MODEL CX-3 warning light

3–3
Before Driving
Keys

A code number is stamped on the plate
attached to the key set; detach this plate
and store it in a safe place (not in the
vehicle) for use if you need to make a
replacement key (auxiliary key).
Also write down the code number and
keep it in a separate safe and convenient
place, but not in the vehicle.

If your key (auxiliary key) is lost, consult
your Authorised Mazda Repairer and have
your code number ready.
NOTE
The driver must carry the key to ensure
the system functions properly.

Auxiliary key Transmitter
Key code number plate

To use the auxiliary key, pull out the
auxiliary key from the transmitter while
pressing the knob.

Knob

Keyless Entry System
This system uses the key buttons to
remotely lock and unlock the doors and
the liftgate.
The system can start the engine without
having to take the key out of your purse or
pocket.
Operating the theft-deterrent system is
also possible on theft-deterrent system-
equipped vehicles.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
 


 KEY Warning Light (Red)
 Refer to Warning/Indicator Lights on
page 4-36 .
 


 Ignition Not Switched Off (STOP)
Warning Beep
  Refer to Ignition Not Switched Off
(STOP) Warning Beep on page 7-65 .
 


 Key Removed from Vehicle Warning
Beep
  Refer to Key Removed from Vehicle
Warning Beep on page 7-66 .

If you have a problem with the key,
consult an expert repairer, we recommend
an Authorised Mazda Repairer.

If your key is lost or stolen, consult an
Authorised Mazda Repairer as soon as
possible for a replacement and to make the
lost or stolen key inoperative.

3–4
Before Driving
Keys
CAUTION
Changes or modi¿ cations not expressly
approved by the party responsible
for compliance could void the user's
authority to operate the equipment.
NOTE
  The keyless entry system operation
may vary due to local conditions.
  The keyless entry system is fully
operational (door/liftgate lock/
unlock) when the ignition is switched
off. The system does not operate
if the ignition is switched to any
position other than off.
  If the key does not operate when
pressing a button or the operational
range becomes too small, the
battery may be weak. To install a
new battery, refer to Key Battery
Replacement (page 6-37 ).

 Battery life is about one year.
Replace the battery with a new one
if the KEY indicator light (green)
À ashes in the instrument cluster.
Replacing the battery about once
a year is recommended because
the KEY warning light/indicator
light may not illuminate or À ash
depending on the rate of battery
depletion.
  Additional keys can be obtained at
an Authorised Mazda Repairer. Up to
6 keys can be used with the keyless
functions per vehicle. Bring all keys
to an Authorised Mazda Repairer
when additional keys are required.

3–5
Before Driving
Keys
Transmitter

Operation buttons Operation indicator light

NOTE
  (European models)  The headlights turn on/off by
operating the transmitter. Refer
to Leaving Home Light on page
4-65 .
  (With theft-deterrent system)  The hazard warning lights À ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on
page 3-46 .
  (With the advanced keyless
function (European models))
 The setting can be changed so that a
beep sound is heard for con¿ rmation
when the doors and the liftgate are
locked/unlocked using the key.
 (With the advanced keyless
function (Except European
models))
 A beep sound can be heard for
con¿ rmation when the doors and the
liftgate are locked/unlocked using the
key. If you prefer, the beep sound can
be turned off.
 The volume of the beep sound can
also be changed.
 Refer to Personalisation Features on
page 9-13 .
NOTE

Use the following procedure to change
the setting.

1. Switch the ignition off and close
all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.
All of the doors and the liftgate
lock and the beep sound activates
at the currently set volume.
The setting changes each time
the LOCK button on the key
is pressed and the beep sound
activates at the set volume. (If the
beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed
by doing any one of the following:
 


 Switching the ignition to ACC
or ON.
 


 Closing the driver's door.



 Opening the liftgate.



 Not operating the key for 10
seconds.
 


 Pressing any button except the
LOCK button on the key.
 


 Pressing a request switch.
The operation indicator light À ashes when
the buttons are pressed.

3–6
Before Driving
Keys
Lock button
To lock the doors and the liftgate, press the
lock button and the hazard warning lights
will À ash once.
(With the advanced keyless function
(Except European models))
A beep sound will be heard once.


NOTE
  (European models)  The doors and the liftgate cannot be
locked by pressing the lock button
while any other door is open. The
hazard warning lights will also not
À ash.
 (Except European models)  The doors and the liftgate cannot be
locked by pressing the lock button
while any other door or the liftgate is
open. The hazard warning lights will
also not À ash.

 (With the i-stop function
(European models))
 Removing the key from the vehicle,
closing all the doors and pressing the
LOCK button on the key while the
i-stop function is operating (engine
is stopped) will switch the ignition
OFF and lock all the doors (Steering
wheel also locks).
 Refer to i-stop on page 4-13 .   Make sure all doors and the liftgate
are locked after pressing the button.
  (With double locking system)  Pressing the lock button twice within
3 seconds will activate the double
locking system.
 Refer to Double Locking System on
page 3-13 .
  (With theft-deterrent system)  When the doors are locked by
pressing the lock button on the key
while the theft-deterrent system is
armed, the hazard warning lights will
À ash once to indicate that the system
is armed.

3–7
Before Driving
Keys
*Some models.
Unlock button
To unlock the doors and the liftgate, press
the unlock button and the hazard warning
lights will À ash twice.
(With the advanced keyless function
(Except European models))
A beep sound will be heard twice.


NOTE
  (Auto re-lock function)  After unlocking with the key,
all doors and the liftgate will
automatically lock if any of the
following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights
will À ash for con¿ rmation.
 The time required for the doors to
lock automatically can be changed.
 Refer to Personalisation Features on
page 9-13 .
 


 A door or the liftgate is opened.



 The ignition is switched to any
position other than off.


 (With theft-deterrent system)  When the doors are unlocked by
pressing the unlock button on the key
while the theft-deterrent system is
turned off, the hazard warning lights
will À ash twice to indicate that the
system is turned off.
Intrusion sensor cancel button *
To cancel the intrusion sensor (part of
the theft-deterrent system), press the
intrusion sensor cancel button within 20
seconds after pressing the lock button and
the hazard warning lights will À ash three
times.
Refer to Theft-Deterrent System on page
3-46 .


Operational Range
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Starting the Engine
NOTE
  Starting the engine may be possible
even if the key is outside of the
vehicle and extremely close to a door
and window, however, always start
the engine from the driver's seat.
 If the vehicle is started and the key
is not in the vehicle, the vehicle will
not restart after it is shut off and the
ignition is switched to off.
  The luggage compartment is out
of the assured operational range,
however, if the key (transmitter) is
operable the engine will start.

3–9
Before Driving
Advanced Keyless Entry System
*Some models.
Advanced Keyless Entry
System
*
WARNING
Radio waves from the key may affect
medical devices such as pacemakers:
Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will affect
the device.
The advanced keyless function allows you
to lock/unlock the door and the liftgate, or
open the liftgate while carrying the key.

System malfunctions or warnings are
indicated by the following warning lights
or beeps.
 






 Request switch Inoperable Warning
Beep
  Refer to Request Switch Inoperable
Warning Beep (With the advanced
keyless function) on page 7-66 .
 


 Key Left-in-luggage Compartment
Warning Beep
  Refer to Key Left-in-luggage
Compartment Warning Beep (With the
advanced keyless function) on page
7-66 .
 


 Key Left-in-vehicle Warning Beep
 Refer to Key Left-in-vehicle Warning
Beep (With the advanced keyless
function) on page 7-66 .

NOTE
The advanced keyless entry system
functions can be deactivated to prevent
any possible adverse effect on a user
wearing a pacemaker or other medical
device. If the system is deactivated,
you will be unable to start the engine
by carrying the key. Consult an expert
repairer, we recommend an Authorised
Mazda Repairer for details. If the
advanced keyless entry system has been
deactivated, you can start the engine by
following the procedure indicated when
the key battery goes dead.
Refer to Engine Start Function When
Key Battery is Dead on page 4-9 .

3–14
Before Driving
Doors and Locks
NOTE
  You can also activate the system
by pressing the lock button on the
transmitter twice within 3 seconds.
  (With the advanced keyless
function)
 You can also activate the system by
pressing the request switch twice
within 3 seconds.
5. The indicator light illuminates for
about 3 seconds to indicate that the
system has been activated.



NOTE
The system cannot be activated when
any door or the liftgate is open.
How to Deactivate the System
Unlock the driver's door or switch the
ignition ON.
NOTE
If the power supply is interrupted (fuse
blows or the battery is disconnected),
the system can only be deactivated by
unlocking a door with the auxiliary key.
Locking, Unlocking with Request
Switch (With the advanced keyless
function)
All doors and the liftgate can be locked/
unlocked by pressing the request switch
on the front doors while the key is being
carried.

The request switch on the liftgate can only
be used to lock all doors and the liftgate.
Front doors

Request switch

Liftgate (Lock only)

Request switch

To lock
To lock the doors and the liftgate, press
the request switch and the hazard warning
lights will À ash once.
(Except European models)
A beep sound will be heard once.

3–15
Before Driving
Doors and Locks
To unlock
To unlock the doors and the liftgate, press
the request switch on a front door and the
hazard warning lights will À ash twice.
(Except European models)
A beep sound will be heard twice.
NOTE
  Con¿ rm that all doors and the liftgate
are securely locked.
 For the liftgate, move it without
pressing the electric liftgate opener
to verify that the liftgate has not been
left ajar.
  (European models)  All doors and the liftgate cannot be
locked when any door is open.
 (Except European models)  All doors and the liftgate cannot be
locked when any door or the liftgate
is open.
  It may require a few seconds for
the doors to unlock after the request
switch is pressed.
  (European models)  The setting can be changed so that a
beep sound is heard for con¿ rmation
when the doors and the liftgate are
locked/unlocked using a request
switch.
 (Except European models)  A beep sound is heard for
con¿ rmation when the doors and the
liftgate are locked/unlocked using
the request switch. If you prefer, the
beep sound can be turned off.
 The volume of the beep sound
can also be changed. Refer to
Personalisation Features on page
9-13 .
NOTE
 Use the following procedure to
change the setting.

1. Switch the ignition off and close
all of the doors and the liftgate.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.
All of the doors and the liftgate
lock and the beep sound activates
at the currently set volume.
The setting changes each time
the LOCK button on the key
is pressed and the beep sound
activates at the set volume. (If the
beep sound has been set to not
activate, it will not activate.)
4. The setting change is completed
by doing any one of the following:
 


 Switching the ignition to ACC
or ON.
 


 Closing the driver's door.



 Opening the liftgate.



 Not operating the key for 10
seconds.
 


 Pressing any button except the
LOCK button on the key.
 


 Pressing a request switch. 



 (With theft-deterrent system)  The hazard warning lights À ash when
the theft-deterrent system is armed or
turned off.
 Refer to Theft-Deterrent System on
page 3-46 .
  (With double locking system)  The double locking system can
be activated/deactivated using the
request switch.
 Refer to Double Locking System on
page 3-13 .