2017 MAZDA MODEL 2 maintenance and care

6–55
Maintenance and Care
Owner Maintenance
5. Disconnect the bulb from the socket.
Rear direction indicator lights



Brake lights/Tail lights
(LED type)
The LED bulb cannot be replaced as a
single unit because it is an integrated
unit.
The LED bulb has to be replaced with
the unit. We recommend an Authorised
Mazda Repairer when the replacement
is necessary.
(Bulb type)



6. Install the new bulb in the reverse order
of the removal procedure.

Reverse lights
S a l o o n
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.


Removal
Installation

4. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your ¿ nger and pulling
the connector.



5. Turn the socket and bulb assembly
anticlockwise and remove it.

6–56
Maintenance and Care
Owner Maintenance
6. Disconnect the bulb from the socket.



7. Install the new bulb in the reverse order
of the removal procedure.

Hatchback
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Remove the cover on the interior
surface of the liftgate.


Removal
Installation
4. Disconnect the connector from the
socket.



5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.



7. Install the new bulb in the reverse order
of the removal procedure.

6–57
Maintenance and Care
Owner Maintenance
*Some models.
Rear fog light *
S a l o o n
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
anticlockwise and remove it.
3. Disconnect the bulb from the socket.



4. Install the new bulb in the reverse order
of the removal procedure.

Hatchback
1. Make sure the ignition is switched off
and the headlight switch is off.
2. Turn the screw anticlockwise and
remove it, and then partially peel back
the mudguard.



3. Turn the socket and bulb assembly
anticlockwise and remove it.
4. Disconnect the bulb from the socket.



5. Install the new bulb in the reverse order
of the removal procedure.

6–58
Maintenance and Care
Owner Maintenance
Number plate lights
S a l o o n
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
3. Peel back the boot lid trim.


Removal
Installation

4. Turn the socket and bulb assembly
anticlockwise and remove it.
5. Disconnect the bulb from the socket.



6. Install the new bulb in the reverse order
of the removal procedure.

Hatchback
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Wrap a À athead screwdriver with a soft
cloth to prevent damage to the light
unit.
3. Insert a À athead screwdriver into the
position shown in the ¿ gure and pull
the light unit outward.



4. Disconnect the electrical connector
from the bulb by pressing the tab on the
connector with your ¿ nger and pulling
the connector.



5. Turn the socket and bulb assembly
anticlockwise and remove it.

6–59
Maintenance and Care
Owner Maintenance
*Some models.
6. Disconnect the bulb from the socket.



7. Install the new bulb in the reverse order
of the removal procedure.

Replacing Interior Light Bulbs
Overhead lights/Map lights * , Overhead
lights (Front) * , Overhead lights (Rear) *
1. Wrap a small À athead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the À athead screwdriver.
2. Disconnect the bulb by pulling it out.
Overhead lights/Map lights
*

6–60
Maintenance and Care
Owner Maintenance
*Some models.
Overhead lights (Front) *



Edge

Overhead lights (Rear) *



Edge

3. Install the new bulb in the reverse order
of the removal procedure.

Boot light (Saloon)
1. Press both sides of the lens cap to
remove it.
2. Disconnect the bulb by pulling it out.



3. Install the new bulb in the reverse order
of the removal procedure.

Luggage compartment light
(Hatchback)
1. Wrap a small À athead screwdriver with
a soft cloth to prevent damage to the
lens and remove the lens by carefully
prying on the edge of the lens with the
À athead screwdriver.
2. Disconnect the bulb by pulling it out.



3. Install the new bulb in the reverse order
of the removal procedure.

6–61
Maintenance and Care
Owner Maintenance
Fuses
Your vehicle's electrical system is
protected by fuses.

If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.

If the same fuse blows again, avoid using
that system and consult an expert repairer,
we recommend an Authorised Mazda
Repairer as soon as possible.
Fuse Replacement
Replacing the fuses on the vehicle's left
side
If the electrical system does not work, ¿ rst
inspect the fuses on the vehicle's left side.


1. Make sure the ignition is switched off,
and other switches are off.
2. Open the fuse panel cover.

3. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.


4. Inspect the fuse and replace it if it is
blown.

NormalBlown

5. Insert a new fuse of the same amperage
rating, and make sure it ¿ ts tightly. If
it does not ¿ t tightly, have an expert
install it. We recommend an Authorised
Mazda Repairer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the AUDIO or OUTLET circuit.
CAUTION
Always replace a fuse with a genuine
Mazda fuse or equivalent of the same
rating. Otherwise you may damage the
electric system.
6. Reinstall the cover and make sure that
it is securely installed.

6–62
Maintenance and Care
Owner Maintenance
Replacing the fuses under the bonnet
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block under the bonnet. If a fuse is blown,
it must be replaced. Follow these steps:


1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.


3. If any fuse but the MAIN fuse is
blown, replace it with a new one of the
same amperage rating .

Normal
Blown

WARNING
Do not replace the main fuse and
multiplex slow blow fuse by yourself.
Have an Authorised Mazda Repairer
perform the replacement:
Replacing these fuses by yourself
is dangerous because they are high
current fuses. Incorrect replacement
could cause an electrical shock or a
short circuit resulting in a ¿ re.
4. Reinstall the cover and make sure that
it is securely installed.