2017 LEXUS RX200T lights

6457-3. Do-it-yourself maintenance
7
Maintenance and care
RX350/RX200t_EE_OM48F32E
■Rear
Back-up light
Rear turn signal light (vehicles with single-beam headlights)
1
2

6467-3. Do-it-yourself maintenance
RX350/RX200t_EE_OM48F32E
■Front turn signal lights (vehicles with single-beam headlights)
To ensure enough space to per-
form work, turn the steering
wheel to rotate the front wheel
away from the bulb to be
replaced.
Remove the 3 fender liner clips.
Turn the steering wheel to the left when replacing the right side lightbulb, and turn the steering wheel to
the right when replacing the left side light bulb.
When removing a fender liner clip,
use a flathead screwdriver to pry the center portion out and then removethe whole clip.
Pull back the fender liner until the
connector is visible.
Partially remove the fender liner
and turn the bulb base
counterclockwise and remove it.
Replacing light bulbs
1
82
3

6477-3. Do-it-yourself maintenance
7
Maintenance and care
RX350/RX200t_EE_OM48F32E
Remove the light bulb.
Install a new light bulb and then
install the bulb base to the light
unit by inserting it and turning it
clockwise.
After installing the bulb base, wiggle it lightly to make sure it is securelyinstalled and turn on the turn signal
lights to visually check that there is no light leaking from between the bulbbase and light unit.
Reinstall the fender liner and
install the 3 fender liner clips.
4
5
6

6487-3. Do-it-yourself maintenance
RX350/RX200t_EE_OM48F32E
■Rear turn signal lights (vehicles with single-beam headlights)
Open the back door and apply
protective tape to the vehicle
body around the taillight.
Use masking tape, etc. Do not use duct tape, as it may leave residue or
damage the paint when removed.
Using a flathead screwdriver,
remove the cover.
To prevent scratching the vehicle, wrap the tip of the flathead screw-driver with a cloth, etc.
Remove the 2 screws.
1
2
3

6507-3. Do-it-yourself maintenance
RX350/RX200t_EE_OM48F32E
Install a new light bulb and then
install the bulb base to the light
unit by inserting it and turning it
clockwise.
After installing the bulb base, wiggle it lightly to make sure it is securelyinstalled and turn on the rear turn sig-
nal lights to visually check that there is no light leaking from between thebulb base and light unit.
Install the light unit.
Align the tabs and push the light unittoward the front of the vehicle toinstall it.
Install the 2 screws.
Install the cover.
Remove the protective tape.
47
8
9
10
11

6517-3. Do-it-yourself maintenance
7
Maintenance and care
RX350/RX200t_EE_OM48F32E
■Back-up lights
Open the back door and remove
the cover.
Using a flathead sc rewdriver, remove the cover.
To prevent scratching to the vehicle,
wrap the tip of the flathead screw- driver with a cloth, etc.
Turn the bulb base
counterclockwise and remove it.
Remove the light bulb.
Install a new light bulb and then
install the bulb base to the light
unit by inserting it and turning it
clockwise.
After installing the bulb base, wiggle
it lightly to make sure it is securely installed and turn on the back-uplights to visually check that there is no
light leaking from between the bulb base and light unit.
1
2
3
4

6527-3. Do-it-yourself maintenance
RX350/RX200t_EE_OM48F32E
Install the cover.
Align the tabs of the cover with the
grooves and install the cover.
■Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by any autho-
rized Lexus dealer or repairer, or another duly qualified and equipped profes-
sional.
●Headlight low beams
●Headlight high beams
●Front turn signal lights (vehicles with triple-beam headlights)
●Front position lights and daytime running lights
●Front fog lights
●Cornering lights (if equipped)
●Rear fog lights
●Rear turn signal light (vehicles with triple-beam headlights)
●Side turn signal lights
●Stop/tail lights
●Rear side marker lights
●High mounted stoplight
●License plate lights
●Outer foot lights
5

6537-3. Do-it-yourself maintenance
7
Maintenance and care
RX350/RX200t_EE_OM48F32E
■LED lights
The headlight low beams, headlight high beams, front turn signal lights (vehicles with tri- ple-beam headlights), front position lights and daytime running lights, front fog lights, cornering lights (if equipped), rear fog lights, rear turn signal light (vehicles with triple-
beam headlights), side turn signal lights, st op/tail lights, rear side marker lights, high mounted stoplight, license plate lights, and outer foot lights consist of a number of LEDs.If any of the LEDs has burned out, take your vehicle to any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional to have the light replaced.
■Condensation build-up on the inside of a lens
Temporary condensation build-up on the inside of the headlight lens does not indicate a
malfunction. Contact any authorized Lexus dealer or repairer, or another duly qualified and equipped professional for more info rmation in the following situations:
●Large drops of water have built up on the inside of a lens.
●Water has built up inside a headlight.
■When replacing light bulbs
 P. 642
WARNING
■To prevent injury
Before performing any light bulb replacement procedure, be sure to turn the engine switch off. Failure to do so may result in burns from hot components or a part of your body may get caught on an operating co mponent, possibly causing serious injury.
■Replacing light bulbs
●Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. When it is unavoid- able to hold the glass portion, use and hold with a clean dry cloth to avoid getting
moisture and oils on the bulb. Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result
in heat damage, fire, or wate r entering the headlight unit. This may damage the head- lights or cause condensation to build up on the lens.
●Do not attempt to repair or disassemble the light bulbs, connectors, electric circuits
or component parts. Doing so may result in death or serious injury due to electric shock.
■To prevent damage or fire
●Make sure bulbs are fully seated and locked.
●Check the wattage of the bulb before installing to prevent heat damage.