2017 LEXUS LS600H tire pressure

5777-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
CAUTION
■After using the tools and jack
Before driving, make sure all the tools and jack are securely in place in their stor-
age location to reduce the possibility of personal injury during a collision or sudden
braking.
NOTICE
■When replacing the tires (vehicles with the tire pressure warning system)
When removing or fitting the wheels, tires or the tire pressure warning valve and
transmitter, contact any authorized Lexus dealer or repairer, or another duly quali-
fied and equipped professional as the tire pressure warning valve and transmitter
may be damaged if not handled correctly.
■To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants, the tire pressure warning valve and
transmitter may not operate properly. If a liquid sealant is used, contact any autho-
rized Lexus dealer or repairer, or another duly qualified and equipped professional
or other qualified service shop as soon as possible. Make sure to replace the tire
pressure warning valve and transmitter when replacing the tire. ( P. 508)

5807-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
■A flat tire that cannot be repaired with the emergency tire puncture repair kit
In the following cases, the tire cannot be repaired with the emergency tire puncture
repair kit. Contact any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional.
●When the tire is damaged due to driving without sufficient air pressure
●When the tire lost air pressure due to a crack or damage in the tire sidewall
●When the tire is visibly separated from the wheel
●When the cut or damage to the tread is 4 mm (0.16 in.) long or more
●When the wheel is damaged
●When 2 or more sharp objects, such as nails or screws, have passed through the
tread on a single tire
●When there is more than one hole or cut in the damaged tire
●When the sealant has expired

5827-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
■Bottle
■Compressor
Emergency tire puncture repair kit components
Hose
Air release cap
Stickers
1
2
3
Compressor switch
Air pressure gauge
Power plug
1
2
3

5877-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
Attach the 2 stickers as shown.
Remove any dirt and moisture from
the wheel before attaching the label. If
it is impossible to attach the label,
make sure to tell any authorized Lexus
dealer or repairer, or another duly
qualified and equipped professional
when you have them repair and
replace the tire that sealant is injected.
Check the specified tire inflation
pressure.
Tire inflation pressure is specified on
the label as shown. ( P. 630)
Start the hybrid system. (P. 247)
To inject the sealant and inflate
the tire, turn the compressor
switch on.
9
10
11
12

5887-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
Inflate the tire until the recom-
mended pressure is reached.
The sealant will be injected and
the pressure will spike to 300
kPa (3.0 kgf/cm2 or bar, 44
psi) or 400 kPa (4.0 kgf/cm2
or bar, 58 psi), then gradually
decrease.
The air pressure gauge will dis-
play the actual tire inflation
pressure about 1 minute (15
minutes at low temperature)
after the switch is turned on.
• Turn the compressor switch off
and then check the tire inflation
pressure. Being careful not to
over inflate, check and repeat
the inflation procedure until the
recommended tire inflation
pressure is reached.
• If the tire inflation pressure is still
lower than the recommended
level after inflation for 10 min-
utes (35 minutes at low tem-
perature) with the switch on, the
tire is too damaged to be
repaired. Turn the compressor
switch off and contact any
authorized Lexus dealer or
repairer, or anot her duly quali-
fied and equipped professional.
• If the tire inflation pressure
exceeds the recommended
level, let out some air to adjust
the tire inflation pressure.
( P. 592, 630)
13
1
2

5907-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
Turn the compressor switch on
and wait for several seconds, then
turn it off. Check the tire inflation
pressure.
If the tire inflation pressure is
below 130 kPa (1.3 kgf/cm
2 or
bar, 19 psi): The puncture can-
not be repaired. Contact any
authorized Lexus dealer or
repairer, or another duly quali-
fied and equipped profes-
sional.
If the tire inflation pressure is
between 130 kPa (1.3 kgf/cm
2
or bar, 19 psi) and a point
below the recommended level:
The tire can be repaired. Pro-
ceed to step .
If the tire inflation pressure is at
the recommended level: Pro-
ceed to step .
Turn the compressor switch on to inflate the tire until the recommended
tire inflation pressure is reached. Drive for about 5 km (3 miles) and
then perform step .
Attach the air release cap to the
end of the hose.
If the air release cap is not attached,
the sealant may leak and the vehicle
may get dirty.
20
1
2
21
3
22
21
19
22

5917-2. Steps to take in an emergency
7
When trouble arises
LS600h/LS600hL_EE(OM50G20E)
Store the bottle in the trunk while it is connected to the compressor.
Taking precautions to avoid sudden braking, sudden acceleration and
sharp turns, drive carefully at under 80 km/h (50 mph) to any autho-
rized Lexus dealer or repairer, or another duly qualified and equipped
professional that is less than 100 km (62 miles) away for tire repair or
replacement.
■Emergency tire puncture repair kit
●The sealant has a limited lifespan. The expiry date is marked on the bottle. The seal-
ant should be replaced before the expiry date. Contact any authorized Lexus
dealer or repairer, or another duly qualified and equipped professional for replace-
ment.
●The sealant stored in the emergency tire puncture repair kit can be used only once
to temporarily repair a single tire. If the sealant has been used and needs to be pur-
chased, contact any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional. The compressor is reusable.
●The sealant can be used when the outside temperature is from -40 C (-40F) to
60 C (140F).
●The kit is exclusively designed for size and type of tires originally installed on your
vehicle. Do not use it for tires that a different size than the original ones, or for any
other purposes.
●If the sealant gets on your clothes, it may stain.
●If the sealant adheres to a wheel or the surface of the vehicle body, the stain may
not be removable if it is not cleaned at once. Immediately wipe away the sealant
with a wet cloth.
●During operation of the kit, a loud operation noise is produced. This does not indi-
cate a malfunction.
●Do not use the emergency tire puncture repair kit to check or to adjust the tire
pressure.
23
24

5927-2. Steps to take in an emergency
LS600h/LS600hL_EE(OM50G20E)
■If the tire is inflated to more than the recommended level
Disconnect the hose from the valve.
Disconnect the hose from the valve, remove the air release cap from the hose and
then reconnect the hose.
Turn the compressor switch on and wait for several seconds, then turn it off. Check
that the air pressure indicator shows the recommended level. ( P. 630)
If the air pressure is lower than the recommended level, turn the compressor
switch on again and repeat the inflation procedure until the recommended pres-
sure is reached.
■After a tire is repaired with the emergency tire puncture repair kit
●The tire pressure warning valve and transmitter should be replaced.
●Even if the tire inflation pressure is at the recommended level, the tire pressure
warning light may come on/flash.
■Note for checking the emergency tire puncture repair kit
Check the sealant expiry date occasionally.
The expiry date is shown on the bottle. Do not use sealant whose expiry date has
already passed. Otherwise, repairs conducted using the emergency tire puncture
repair kit may not be performed properly.
Install the air release cap to the end of the
hose and push the protrusion on the air
release cap into the valve to let some air
out.
1
2
3
4